DEBUG parameter - This is the SBOD history buffer.
Parsed from file sync.mib.txt
Company: None
Module: Wellfleet-SYNC-MIB
DEBUG parameter - This is the SBOD history buffer.
Parsed from file Wellfleet-SYNC-MIB.mib
Module: Wellfleet-SYNC-MIB
Vendor: Wellfleet
Module: Wellfleet-SYNC-MIB
[Automatically extracted from oidview.com]
wfSyncBODHistory OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "DEBUG parameter - This is the SBOD history buffer." ::= { wfSyncEntry 105 }
wfSyncBODHistory OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "DEBUG parameter - This is the SBOD history buffer." ::= { wfSyncEntry 105 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.18.3.4.5.1.55 | wfSyncCfgTxQueueLength | 0 | 0 | Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special me… |
| 1.3.6.1.4.1.18.3.4.5.1.56 | wfSyncCfgRxQueueLength | 0 | 0 | Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special mea… |
| 1.3.6.1.4.1.18.3.4.5.1.57 | wfSyncTxQueueLength | 0 | 0 | Current Transmit Queue Length. |
| 1.3.6.1.4.1.18.3.4.5.1.58 | wfSyncRxQueueLength | 0 | 0 | Current Receive Queue Length. |
| 1.3.6.1.4.1.18.3.4.5.1.59 | wfSyncRxReplenMisses | 0 | 0 | Number of packet buffer misses while attempting to replenish driver receive ring. |
| 1.3.6.1.4.1.18.3.4.5.1.60 | wfSyncStartUpMode | 0 | 0 | Initiation of link level for LLC2 running LAPB |
| 1.3.6.1.4.1.18.3.4.5.1.61 | wfSyncIdleRRFrames | 0 | 0 | Transmit Link level RR's (Reciever Readys) during idle time. Every wfSyncLinkIdleTimer expiration an RR will be sent. |
| 1.3.6.1.4.1.18.3.4.5.1.62 | wfSyncMultilineMode | 0 | 0 | This indicates the roll the sync line plays in a Bandwidth on Demand multiline circuit. If this is not BOD, the mode is standard. |
| 1.3.6.1.4.1.18.3.4.5.1.63 | wfSyncBODExamPeriod | 0 | 0 | This indicates the interval that the line should be polled for possible congestion. This value is in tenths of a second |
| 1.3.6.1.4.1.18.3.4.5.1.64 | wfSyncBODFullThreshold | 0 | 0 | This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered … |
| 1.3.6.1.4.1.18.3.4.5.1.65 | wfSyncBODRecoverThreshold | 0 | 0 | This is the recovery threshold expressed as a percentage of the theoretical maximum line throughput. The actual throughput must… |
| 1.3.6.1.4.1.18.3.4.5.1.66 | wfSyncBODPeriodsToFail | 0 | 0 | This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the lin… |
| 1.3.6.1.4.1.18.3.4.5.1.67 | wfSyncKG84ACycle | 0 | 0 | Monitor sample time in milliseconds |
| 1.3.6.1.4.1.18.3.4.5.1.68 | wfSyncKG84ASyncLossInterval | 0 | 0 | timer starts when FCS error detected; if no good frame received during this time, declare loss of synchronization |
| 1.3.6.1.4.1.18.3.4.5.1.69 | wfSyncKG84ARemoteResyncWait | 0 | 0 | when loss of synchronization is detected, and CTS is low, start timer; if CTS is not high when timer expires, force sync request |
| 1.3.6.1.4.1.18.3.4.5.1.70 | wfSyncKG84ASyncPulse | 0 | 0 | interval to pulse KG84a SYNC signal, in milliseconds |
| 1.3.6.1.4.1.18.3.4.5.1.71 | wfSyncKG84AResyncs | 0 | 0 | number of KG84 resyncs performed |
| 1.3.6.1.4.1.18.3.4.5.1.72 | wfSyncKG84AResyncsDetected | 0 | 0 | number of KG84 resyncs detected |
| 1.3.6.1.4.1.18.3.4.5.1.73 | wfSyncKG84ABsu | 0 | 0 | value taken from mk5025 sync chip control block |
| 1.3.6.1.4.1.18.3.4.5.1.74 | wfSyncKG84AState | 0 | 0 | state of sync |
| 1.3.6.1.4.1.18.3.4.5.1.75 | wfSyncKG84AOkFrames | 0 | 0 | count of valid frames received. This value taken from normal sync processing, updated by timer routine when FCE error detected |
| 1.3.6.1.4.1.18.3.4.5.1.76 | wfSyncPollingEnable | 0 | 0 | Enable or Disable Sync Polling. When Sync Polling is enabled, the the Sync Driver will be disabled if the DSR lead is dropped. I… |
| 1.3.6.1.4.1.18.3.4.5.1.77 | wfSyncBackupPool | 0 | 0 | Backup pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.78 | wfSyncDemandPool | 0 | 0 | Dial on demand pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.79 | wfSyncLineNumber | 0 | 0 | line number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.80 | wfSyncHoldDownTime | 0 | 0 | Wait this number of seconds before bringing the line up. This prevents line waffling if this is a reactivated primary line in a b… |
| 1.3.6.1.4.1.18.3.4.5.1.81 | wfSyncNetworkType | 0 | 0 | Specific Network Link Level to be executed, LAPB mode only. The types GOSIP and NET2 are used in conjunction with an MK5025 chip … |
| 1.3.6.1.4.1.18.3.4.5.1.82 | wfSyncActiveCct | 0 | 0 | Active CCT number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.83 | wfSyncCableType | 0 | 0 | Type of Cable attached to the sync port - this is needed for V.25bis and Raise DTR to properly communicate with the modem |
| 1.3.6.1.4.1.18.3.4.5.1.84 | wfSyncRxDropPackets | 0 | 0 | Number of Rx packets dropped by driver. |
| 1.3.6.1.4.1.18.3.4.5.1.85 | wfSyncTxDropPackets | 0 | 0 | Number of Tx packets dropped by driver. |
| 1.3.6.1.4.1.18.3.4.5.1.86 | wfSyncModule | 0 | 0 | Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.5.1.87 | wfSyncActualConnector | 0 | 0 | Actual connector number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.5.1.88 | wfSyncLineCoding | 0 | 0 | Line Coding for sync interface. Can be either NRZ or NRZI. |
| 1.3.6.1.4.1.18.3.4.5.1.89 | wfSyncLastChange | 0 | 0 | The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the… |
| 1.3.6.1.4.1.18.3.4.5.1.90 | wfSyncOutQLen | 0 | 0 | The instantaneous current length of the output packet queue (in packets). |
| 1.3.6.1.4.1.18.3.4.5.1.91 | wfSyncRemoteLpbkDetection | 0 | 0 | This attribute enables Remote Loopback Detection. When enabled along with wfSyncBofl, the device driver will detect when it is … |
| 1.3.6.1.4.1.18.3.4.5.1.92 | wfSyncLastState | 0 | 0 | The state which the driver was in prior to the most recent re-initialization. |
| 1.3.6.1.4.1.18.3.4.5.1.93 | wfSyncExternalClkSpeed | 0 | 0 | External Clock Speed. If external clocking is configured, this attribute should be set to the clock speed of the externally supp… |
| 1.3.6.1.4.1.18.3.4.5.1.94 | wfSyncBChannelOverride | 0 | 0 | For ISDN, indicates which B Channel we're using. By default, we'd like the B Channel tied to the connector defined in the instan… |
| 1.3.6.1.4.1.18.3.4.5.1.95 | wfSyncBChannel | 0 | 0 | Indicates which B Channel is running |
| 1.3.6.1.4.1.18.3.4.5.1.96 | wfSyncForceIFTF | 0 | 0 | Specifies the Inter Frame Time Fill (IFTF) pattern which gets transmitted when no data is being transmitted on a particular chan… |
| 1.3.6.1.4.1.18.3.4.5.1.97 | wfSyncPriority | 0 | 0 | Used by dial/switched services to assign priority of lines within the same demand or backup pool |
| 1.3.6.1.4.1.18.3.4.5.1.98 | wfSyncTurboBofl | 0 | 0 | DEBUG parameter - Turbo bofl enabled or disabled |
| 1.3.6.1.4.1.18.3.4.5.1.99 | wfSyncBoflNum | 0 | 0 | DEBUG parameter - Number of breath of life packets per breath of life |
| 1.3.6.1.4.1.18.3.4.5.1.100 | wfSyncBoflLen | 0 | 0 | DEBUG parameter - breath of life packet length |
| 1.3.6.1.4.1.18.3.4.5.1.101 | wfSyncTurboBoflMisses | 0 | 0 | DEBUG parameter - breath of life allocation failures |
| 1.3.6.1.4.1.18.3.4.5.1.102 | wfSyncTurboBoflInvocations | 0 | 0 | DEBUG parameter - breath of life invocations |
| 1.3.6.1.4.1.18.3.4.5.1.103 | wfSyncBandwidthOnDemandPool | 0 | 0 | Bandwidth pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.104 | wfSyncBODRecoverPeriodsToPass | 0 | 0 | This is the number of consecutive periods where the queue depth is below the congestion threshold required to declare the line co… |
| 1.3.6.1.4.1.18.3.4.5.1.106 | wfSyncBODDebugFlag | 0 | 0 | DEBUG parameter - This is the SBOD Debug flag, used to control debug code for SBOD. |
| 1.3.6.1.4.1.18.3.4.5.1.107 | wfSyncBChRateAdaption | 0 | 0 | This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in l… |
| 1.3.6.1.4.1.18.3.4.5.1.108 | wfSyncBChActualRateAdaption | 0 | 0 | Indicates the current B Channel Rate Adaption in use. This attribute is only relevant when this Synchronous device driver is per… |
| 1.3.6.1.4.1.18.3.4.5.1.109 | wfSyncWanType | 0 | 0 | This attribute indicates whether this port should be configured as a SYNCHRONOUS or UART/ASYNCHRONOUS interface. |
| 1.3.6.1.4.1.18.3.4.5.1.110 | wfSyncAsyncBaudRate | 0 | 0 | Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but… |
| 1.3.6.1.4.1.18.3.4.5.1.111 | wfSyncCfgAsyncCmndMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) between ASYNC frames. Values other than zero over-ride the router selecte… |
| 1.3.6.1.4.1.18.3.4.5.1.112 | wfSyncAsyncCmndMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have not yet connected & entered data state), befor… |
| 1.3.6.1.4.1.18.3.4.5.1.113 | wfSyncCfgAsyncDataMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Data Mode) between ASYNC frames. Values other than zero over-ride the router selected v… |
| 1.3.6.1.4.1.18.3.4.5.1.114 | wfSyncAsyncDataMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have connected & entered data state), before closin… |
| 1.3.6.1.4.1.18.3.4.5.1.115 | wfSyncFramesAbortTx | 0 | 0 | Number of frames where CTS was lost during transmission. |
| 1.3.6.1.4.1.18.3.4.5.1.116 | wfSyncPasyncParityType | 0 | 0 | Type of parity chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.117 | wfSyncPasyncCharacterLength | 0 | 0 | Number of data bits chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.118 | wfSyncPasyncStopLength | 0 | 0 | Number of stop bits chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.119 | wfSyncPasyncBaudRate | 0 | 0 | Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but… |
| 1.3.6.1.4.1.18.3.4.5.1.120 | wfSyncLocalConnectionState | 0 | 0 | The state of the cable at the router end. |
| 1.3.6.1.4.1.18.3.4.5.1.121 | wfSyncRemoteConnectionState | 0 | 0 | The state of the cable at the device end. |
| 1.3.6.1.4.1.18.3.4.5.1.122 | wfSyncTimeSlotAssignment | 0 | 0 | Lists the time-slots which constitute this channel. Read only attribute that contains a list of time-slots from 1 to 24 used by t… |
| 1.3.6.1.4.1.18.3.4.5.1.123 | wfSyncEiaStatus | 0 | 0 | The state of the EIA signals at the router interface. The signals are designated as bits in this entry. If the signal is asserted… |
| 1.3.6.1.4.1.18.3.4.5.1.124 | wfSyncEiaStatusReset | 0 | 0 | Reset The EIA status for the EIA signals in wfSyncEiaStatus. This is particularly useful for clearing the toggle status. |
| 1.3.6.1.4.1.18.3.4.5.1.125 | wfSyncUcastMap | 0 | 0 | Used to map ifEntry.ifInUcastPkts to wfSyncRxFrames and ifEntry.ifOutUcastPkts to wfSyncTxFrames. |
| 1.3.6.1.4.1.18.3.4.5.1.126 | wfSyncAsyncCfgMaxIdleTimer | 0 | 0 | Determines if Async Max Idle Timer should be based on the baudrate or on the time needed to receive three characters. |
| 1.3.6.1.4.1.18.3.4.5.1.127 | wfSyncPasyncMaxIdles | 0 | 0 | Maximum number of idles we'll receive between ASYNC frames. Values other than zero over-ride wfSyncAsyncCfgMaxIdleTimer. This att… |
| ... | ||||