This is the recovery threshold expressed as a percentage of the
theoretical maximum line throughput. The actual throughput must fall
below this percentage in order for the BOD circuit to
revert back to the primary line only. This value should be
set to less than one half the value of wfSyncBODFullThreshold
to avoid toggling the secondary.
Parsed from file sync.mib.txt
Company: None
Module: Wellfleet-SYNC-MIB
This is the recovery threshold expressed as a percentage of the
theoretical maximum line throughput. The actual throughput must fall
below this percentage in order for the BOD circuit to
revert back to the primary line only. This value should be
set to less than one half the value of wfSyncBODFullThreshold
to avoid toggling the secondary.
Parsed from file Wellfleet-SYNC-MIB.mib
Module: Wellfleet-SYNC-MIB
Vendor: Wellfleet
Module: Wellfleet-SYNC-MIB
[Automatically extracted from oidview.com]
wfSyncBODRecoverThreshold OBJECT-TYPE SYNTAX INTEGER(10..100) ACCESS read-write STATUS mandatory DESCRIPTION "This is the recovery threshold expressed as a percentage of the theoretical maximum line throughput. The actual throughput must fall below this percentage in order for the BOD circuit to revert back to the primary line only. This value should be set to less than one half the value of wfSyncBODFullThreshold to avoid toggling the secondary." DEFVAL { 20 } ::= { wfSyncEntry 65 }
wfSyncBODRecoverThreshold OBJECT-TYPE SYNTAX INTEGER(10..100) ACCESS read-write STATUS mandatory DESCRIPTION "This is the recovery threshold expressed as a percentage of the theoretical maximum line throughput. The actual throughput must fall below this percentage in order for the BOD circuit to revert back to the primary line only. This value should be set to less than one half the value of wfSyncBODFullThreshold to avoid toggling the secondary." DEFVAL { 20 } ::= { wfSyncEntry 65 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.18.3.4.5.1.15 | wfSyncSignalMode | 0 | 0 | The signal mode parameter indicates the line paramter balanced or unbalanced. |
| 1.3.6.1.4.1.18.3.4.5.1.16 | wfSyncRtsEnable | 0 | 0 | Note: In KG84 support, RTS has a different meaning |
| 1.3.6.1.4.1.18.3.4.5.1.17 | wfSyncBurstCount | 0 | 0 | Allows control over the DMA burst cycle duration on MK5025 based products. This attribute is ignored for AN and ASN products. T… |
| 1.3.6.1.4.1.18.3.4.5.1.18 | wfSyncService | 0 | 0 | Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. … |
| 1.3.6.1.4.1.18.3.4.5.1.19 | wfSyncRetryCount | 0 | 0 | The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determi… |
| 1.3.6.1.4.1.18.3.4.5.1.20 | wfSyncLinkIdleTimer | 0 | 0 | The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disco… |
| 1.3.6.1.4.1.18.3.4.5.1.21 | wfSyncRetryTimer | 0 | 0 | The Retry Timer parameter indicates the timeout in tenths of seconds for a response to be heard form the link. Link control fra… |
| 1.3.6.1.4.1.18.3.4.5.1.22 | wfSyncExtendedAddress | 0 | 0 | This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address … |
| 1.3.6.1.4.1.18.3.4.5.1.23 | wfSyncExtendedAddressForce | 0 | 0 | When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first … |
| 1.3.6.1.4.1.18.3.4.5.1.24 | wfSyncExtendedControl | 0 | 0 | This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I … |
| 1.3.6.1.4.1.18.3.4.5.1.25 | wfSyncExtendedControlForce | 0 | 0 | This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the co… |
| 1.3.6.1.4.1.18.3.4.5.1.26 | wfSyncConnectAttempts | 0 | 0 | This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is… |
| 1.3.6.1.4.1.18.3.4.5.1.27 | wfSyncWindowSizeTx | 0 | 0 | The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode. |
| 1.3.6.1.4.1.18.3.4.5.1.28 | wfSyncWindowSizeTxExtc | 0 | 0 | The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode. |
| 1.3.6.1.4.1.18.3.4.5.1.29 | wfSyncMinFrameSpace | 0 | 0 | The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames. |
| 1.3.6.1.4.1.18.3.4.5.1.30 | wfSyncLocalAddress | 0 | 0 | The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets i… |
| 1.3.6.1.4.1.18.3.4.5.1.31 | wfSyncRemoteAddress | 0 | 0 | The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets … |
| 1.3.6.1.4.1.18.3.4.5.1.32 | wfSyncPassThruLocalMadr | 0 | 0 | 48 bit MAC address of Local end of Sync Passthru circuit |
| 1.3.6.1.4.1.18.3.4.5.1.33 | wfSyncPassThruRemoteMadr | 0 | 0 | 48 bit MAC address of Remote end of Sync Passthru circuit |
| 1.3.6.1.4.1.18.3.4.5.1.34 | wfSyncWanProtocol | 0 | 0 | WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface. |
| 1.3.6.1.4.1.18.3.4.5.1.35 | wfSyncCrcSize | 0 | 0 | CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC |
| 1.3.6.1.4.1.18.3.4.5.1.36 | wfSyncRxOctets | 0 | 0 | Number of octets received without error |
| 1.3.6.1.4.1.18.3.4.5.1.37 | wfSyncRxFrames | 0 | 0 | Number of frames received without error |
| 1.3.6.1.4.1.18.3.4.5.1.38 | wfSyncTxOctets | 0 | 0 | Number of octets transmitted without error |
| 1.3.6.1.4.1.18.3.4.5.1.39 | wfSyncTxFrames | 0 | 0 | Number of frames transmitted without error |
| 1.3.6.1.4.1.18.3.4.5.1.40 | wfSyncRxErrors | 0 | 0 | Number of receive errors |
| 1.3.6.1.4.1.18.3.4.5.1.41 | wfSyncTxErrors | 0 | 0 | Number of transmission errors |
| 1.3.6.1.4.1.18.3.4.5.1.42 | wfSyncLackRescRx | 0 | 0 | Number of Rx frames dropped due to lack of buffer resources |
| 1.3.6.1.4.1.18.3.4.5.1.43 | wfSyncLackRescTx | 0 | 0 | Number of frames clipped in driver's transmit routine due to transmit congestion. |
| 1.3.6.1.4.1.18.3.4.5.1.44 | wfSyncUnderFlowTx | 0 | 0 | Number of transmission underflows, device FIFO went empty before next DMA request was granted. |
| 1.3.6.1.4.1.18.3.4.5.1.45 | wfSyncRejectsTx | 0 | 0 | For the mk50 driver: Number of reject frames which were transmitted For the quicsync driver: Not used For the quicsync driver in A… |
| 1.3.6.1.4.1.18.3.4.5.1.46 | wfSyncRejectsRx | 0 | 0 | For the mk50 driver: Number of reject frames which were received For the quicsync driver: Number of HDLC frames received with a no… |
| 1.3.6.1.4.1.18.3.4.5.1.47 | wfSyncOverFlowRx | 0 | 0 | Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available. |
| 1.3.6.1.4.1.18.3.4.5.1.48 | wfSyncFramesIncompRx | 0 | 0 | Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors. |
| 1.3.6.1.4.1.18.3.4.5.1.49 | wfSyncBadFramesRx | 0 | 0 | Number of bad receive frames, caused by FCS errors or non octet aligned. |
| 1.3.6.1.4.1.18.3.4.5.1.50 | wfSyncFrameRejectsRx | 0 | 0 | Number of Frame Rejects received |
| 1.3.6.1.4.1.18.3.4.5.1.51 | wfSyncRuntsRx | 0 | 0 | Number of runt frames received or number of frames where the Carrier Detect signal was lost during reception. |
| 1.3.6.1.4.1.18.3.4.5.1.52 | wfSyncT1Timeouts | 0 | 0 | Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T… |
| 1.3.6.1.4.1.18.3.4.5.1.53 | wfSyncMemoryErrors | 0 | 0 | Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us. |
| 1.3.6.1.4.1.18.3.4.5.1.54 | wfSyncMediaType | 0 | 0 | Media type selection is provided via this parameter |
| 1.3.6.1.4.1.18.3.4.5.1.55 | wfSyncCfgTxQueueLength | 0 | 0 | Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special me… |
| 1.3.6.1.4.1.18.3.4.5.1.56 | wfSyncCfgRxQueueLength | 0 | 0 | Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special mea… |
| 1.3.6.1.4.1.18.3.4.5.1.57 | wfSyncTxQueueLength | 0 | 0 | Current Transmit Queue Length. |
| 1.3.6.1.4.1.18.3.4.5.1.58 | wfSyncRxQueueLength | 0 | 0 | Current Receive Queue Length. |
| 1.3.6.1.4.1.18.3.4.5.1.59 | wfSyncRxReplenMisses | 0 | 0 | Number of packet buffer misses while attempting to replenish driver receive ring. |
| 1.3.6.1.4.1.18.3.4.5.1.60 | wfSyncStartUpMode | 0 | 0 | Initiation of link level for LLC2 running LAPB |
| 1.3.6.1.4.1.18.3.4.5.1.61 | wfSyncIdleRRFrames | 0 | 0 | Transmit Link level RR's (Reciever Readys) during idle time. Every wfSyncLinkIdleTimer expiration an RR will be sent. |
| 1.3.6.1.4.1.18.3.4.5.1.62 | wfSyncMultilineMode | 0 | 0 | This indicates the roll the sync line plays in a Bandwidth on Demand multiline circuit. If this is not BOD, the mode is standard. |
| 1.3.6.1.4.1.18.3.4.5.1.63 | wfSyncBODExamPeriod | 0 | 0 | This indicates the interval that the line should be polled for possible congestion. This value is in tenths of a second |
| 1.3.6.1.4.1.18.3.4.5.1.64 | wfSyncBODFullThreshold | 0 | 0 | This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered … |
| 1.3.6.1.4.1.18.3.4.5.1.66 | wfSyncBODPeriodsToFail | 0 | 0 | This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the lin… |
| 1.3.6.1.4.1.18.3.4.5.1.67 | wfSyncKG84ACycle | 0 | 0 | Monitor sample time in milliseconds |
| 1.3.6.1.4.1.18.3.4.5.1.68 | wfSyncKG84ASyncLossInterval | 0 | 0 | timer starts when FCS error detected; if no good frame received during this time, declare loss of synchronization |
| 1.3.6.1.4.1.18.3.4.5.1.69 | wfSyncKG84ARemoteResyncWait | 0 | 0 | when loss of synchronization is detected, and CTS is low, start timer; if CTS is not high when timer expires, force sync request |
| 1.3.6.1.4.1.18.3.4.5.1.70 | wfSyncKG84ASyncPulse | 0 | 0 | interval to pulse KG84a SYNC signal, in milliseconds |
| 1.3.6.1.4.1.18.3.4.5.1.71 | wfSyncKG84AResyncs | 0 | 0 | number of KG84 resyncs performed |
| 1.3.6.1.4.1.18.3.4.5.1.72 | wfSyncKG84AResyncsDetected | 0 | 0 | number of KG84 resyncs detected |
| 1.3.6.1.4.1.18.3.4.5.1.73 | wfSyncKG84ABsu | 0 | 0 | value taken from mk5025 sync chip control block |
| 1.3.6.1.4.1.18.3.4.5.1.74 | wfSyncKG84AState | 0 | 0 | state of sync |
| 1.3.6.1.4.1.18.3.4.5.1.75 | wfSyncKG84AOkFrames | 0 | 0 | count of valid frames received. This value taken from normal sync processing, updated by timer routine when FCE error detected |
| 1.3.6.1.4.1.18.3.4.5.1.76 | wfSyncPollingEnable | 0 | 0 | Enable or Disable Sync Polling. When Sync Polling is enabled, the the Sync Driver will be disabled if the DSR lead is dropped. I… |
| 1.3.6.1.4.1.18.3.4.5.1.77 | wfSyncBackupPool | 0 | 0 | Backup pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.78 | wfSyncDemandPool | 0 | 0 | Dial on demand pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.79 | wfSyncLineNumber | 0 | 0 | line number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.80 | wfSyncHoldDownTime | 0 | 0 | Wait this number of seconds before bringing the line up. This prevents line waffling if this is a reactivated primary line in a b… |
| 1.3.6.1.4.1.18.3.4.5.1.81 | wfSyncNetworkType | 0 | 0 | Specific Network Link Level to be executed, LAPB mode only. The types GOSIP and NET2 are used in conjunction with an MK5025 chip … |
| 1.3.6.1.4.1.18.3.4.5.1.82 | wfSyncActiveCct | 0 | 0 | Active CCT number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.83 | wfSyncCableType | 0 | 0 | Type of Cable attached to the sync port - this is needed for V.25bis and Raise DTR to properly communicate with the modem |
| 1.3.6.1.4.1.18.3.4.5.1.84 | wfSyncRxDropPackets | 0 | 0 | Number of Rx packets dropped by driver. |
| 1.3.6.1.4.1.18.3.4.5.1.85 | wfSyncTxDropPackets | 0 | 0 | Number of Tx packets dropped by driver. |
| 1.3.6.1.4.1.18.3.4.5.1.86 | wfSyncModule | 0 | 0 | Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.5.1.87 | wfSyncActualConnector | 0 | 0 | Actual connector number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.5.1.88 | wfSyncLineCoding | 0 | 0 | Line Coding for sync interface. Can be either NRZ or NRZI. |
| 1.3.6.1.4.1.18.3.4.5.1.89 | wfSyncLastChange | 0 | 0 | The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the… |
| 1.3.6.1.4.1.18.3.4.5.1.90 | wfSyncOutQLen | 0 | 0 | The instantaneous current length of the output packet queue (in packets). |
| 1.3.6.1.4.1.18.3.4.5.1.91 | wfSyncRemoteLpbkDetection | 0 | 0 | This attribute enables Remote Loopback Detection. When enabled along with wfSyncBofl, the device driver will detect when it is … |
| 1.3.6.1.4.1.18.3.4.5.1.92 | wfSyncLastState | 0 | 0 | The state which the driver was in prior to the most recent re-initialization. |
| 1.3.6.1.4.1.18.3.4.5.1.93 | wfSyncExternalClkSpeed | 0 | 0 | External Clock Speed. If external clocking is configured, this attribute should be set to the clock speed of the externally supp… |
| 1.3.6.1.4.1.18.3.4.5.1.94 | wfSyncBChannelOverride | 0 | 0 | For ISDN, indicates which B Channel we're using. By default, we'd like the B Channel tied to the connector defined in the instan… |
| 1.3.6.1.4.1.18.3.4.5.1.95 | wfSyncBChannel | 0 | 0 | Indicates which B Channel is running |
| 1.3.6.1.4.1.18.3.4.5.1.96 | wfSyncForceIFTF | 0 | 0 | Specifies the Inter Frame Time Fill (IFTF) pattern which gets transmitted when no data is being transmitted on a particular chan… |
| 1.3.6.1.4.1.18.3.4.5.1.97 | wfSyncPriority | 0 | 0 | Used by dial/switched services to assign priority of lines within the same demand or backup pool |
| 1.3.6.1.4.1.18.3.4.5.1.98 | wfSyncTurboBofl | 0 | 0 | DEBUG parameter - Turbo bofl enabled or disabled |
| 1.3.6.1.4.1.18.3.4.5.1.99 | wfSyncBoflNum | 0 | 0 | DEBUG parameter - Number of breath of life packets per breath of life |
| 1.3.6.1.4.1.18.3.4.5.1.100 | wfSyncBoflLen | 0 | 0 | DEBUG parameter - breath of life packet length |
| 1.3.6.1.4.1.18.3.4.5.1.101 | wfSyncTurboBoflMisses | 0 | 0 | DEBUG parameter - breath of life allocation failures |
| 1.3.6.1.4.1.18.3.4.5.1.102 | wfSyncTurboBoflInvocations | 0 | 0 | DEBUG parameter - breath of life invocations |
| 1.3.6.1.4.1.18.3.4.5.1.103 | wfSyncBandwidthOnDemandPool | 0 | 0 | Bandwidth pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.104 | wfSyncBODRecoverPeriodsToPass | 0 | 0 | This is the number of consecutive periods where the queue depth is below the congestion threshold required to declare the line co… |
| 1.3.6.1.4.1.18.3.4.5.1.105 | wfSyncBODHistory | 0 | 0 | DEBUG parameter - This is the SBOD history buffer. |
| 1.3.6.1.4.1.18.3.4.5.1.106 | wfSyncBODDebugFlag | 0 | 0 | DEBUG parameter - This is the SBOD Debug flag, used to control debug code for SBOD. |
| 1.3.6.1.4.1.18.3.4.5.1.107 | wfSyncBChRateAdaption | 0 | 0 | This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in l… |
| 1.3.6.1.4.1.18.3.4.5.1.108 | wfSyncBChActualRateAdaption | 0 | 0 | Indicates the current B Channel Rate Adaption in use. This attribute is only relevant when this Synchronous device driver is per… |
| 1.3.6.1.4.1.18.3.4.5.1.109 | wfSyncWanType | 0 | 0 | This attribute indicates whether this port should be configured as a SYNCHRONOUS or UART/ASYNCHRONOUS interface. |
| 1.3.6.1.4.1.18.3.4.5.1.110 | wfSyncAsyncBaudRate | 0 | 0 | Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but… |
| 1.3.6.1.4.1.18.3.4.5.1.111 | wfSyncCfgAsyncCmndMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) between ASYNC frames. Values other than zero over-ride the router selecte… |
| 1.3.6.1.4.1.18.3.4.5.1.112 | wfSyncAsyncCmndMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have not yet connected & entered data state), befor… |
| 1.3.6.1.4.1.18.3.4.5.1.113 | wfSyncCfgAsyncDataMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Data Mode) between ASYNC frames. Values other than zero over-ride the router selected v… |
| 1.3.6.1.4.1.18.3.4.5.1.114 | wfSyncAsyncDataMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have connected & entered data state), before closin… |
| 1.3.6.1.4.1.18.3.4.5.1.115 | wfSyncFramesAbortTx | 0 | 0 | Number of frames where CTS was lost during transmission. |
| ... | ||||