Specifies the application that the LogicalLines of this Port will provide.
NONPRI indicates that all of the LogicalLines will have a permanent Cct
number and will not be used to dial to varying destinations. PRI
indicates that some or all of the ds0s of this port will be used for switched
Ccts using ISDN. MIXED indicates that some of the ds0s are being used for
switched Ccts using ISDN and some are being used for non PRI permanent
connections for other applications such as leased lines or Frame Relay.
Parsed from file ds1e1.mib.txt
Company: None
Module: Wellfleet-DS1E1-MIB
Specifies the application that the LogicalLines of this Port will provide.
NONPRI indicates that all of the LogicalLines will have a permanent Cct
number and will not be used to dial to varying destinations. PRI
indicates that some or all of the ds0s of this port will be used for switched
Ccts using ISDN. MIXED indicates that some of the ds0s are being used for
switched Ccts using ISDN and some are being used for non PRI permanent
connections for other applications such as leased lines or Frame Relay.
Parsed from file Wellfleet-DS1E1-MIB.mib
Module: Wellfleet-DS1E1-MIB
Vendor: Wellfleet
Module: Wellfleet-DS1E1-MIB
[Automatically extracted from oidview.com]
wfDs1E1PortLineApplication OBJECT-TYPE SYNTAX INTEGER { nonpri(1), pri(2), mixed(3), frswpri(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the application that the LogicalLines of this Port will provide. NONPRI indicates that all of the LogicalLines will have a permanent Cct number and will not be used to dial to varying destinations. PRI indicates that some or all of the ds0s of this port will be used for switched Ccts using ISDN. MIXED indicates that some of the ds0s are being used for switched Ccts using ISDN and some are being used for non PRI permanent connections for other applications such as leased lines or Frame Relay." DEFVAL { nonpri } ::= { wfDs1E1PortEntry 16 }
wfDs1E1PortLineApplication OBJECT-TYPE SYNTAX INTEGER { nonpri(1), pri(2), mixed(3), frswpri(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the application that the LogicalLines of this Port will provide. NONPRI indicates that all of the LogicalLines will have a permanent Cct number and will not be used to dial to varying destinations. PRI indicates that some or all of the ds0s of this port will be used for switched Ccts using ISDN. MIXED indicates that some of the ds0s are being used for switched Ccts using ISDN and some are being used for non PRI permanent connections for other applications such as leased lines or Frame Relay." DEFVAL { nonpri } ::= { wfDs1E1PortEntry 16 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.4.9.3.1.1 | wfDs1E1PortDelete | 0 | 0 | Create/Delete parameter |
| 1.3.6.1.4.1.18.3.4.9.3.1.2 | wfDs1E1PortDisable | 0 | 0 | Enable/Disable parameter |
| 1.3.6.1.4.1.18.3.4.9.3.1.3 | wfDs1E1PortState | 0 | 0 | Line Driver state variable |
| 1.3.6.1.4.1.18.3.4.9.3.1.4 | wfDs1E1PortLineNumber | 0 | 0 | LineNumber for this port. This value is assigned at configuration time and uniquely identifies this interface. This LineNumber … |
| 1.3.6.1.4.1.18.3.4.9.3.1.5 | wfDs1E1PortMtu | 0 | 0 | MTU parameter. Obsoleted, it is no longer referenced. |
| 1.3.6.1.4.1.18.3.4.9.3.1.6 | wfDs1E1PortSignalLevel | 0 | 0 | Specifies T1 transmit power level, in terms of DB. They translate into cable length as follows: 0.0dB -> 0-133 ft 0.5dB -> 133-2… |
| 1.3.6.1.4.1.18.3.4.9.3.1.7 | wfDs1E1PortSetupAlarmThreshold | 0 | 0 | Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the ti… |
| 1.3.6.1.4.1.18.3.4.9.3.1.8 | wfDs1E1PortClearAlarmThreshold | 0 | 0 | Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for gr… |
| 1.3.6.1.4.1.18.3.4.9.3.1.9 | wfDs1E1PortFdlTargetHdlcAddress | 0 | 0 | Selects between the two FDL target address modes. This determines whether the near-end FDL will respond to HDLC address AZ or BY … |
| 1.3.6.1.4.1.18.3.4.9.3.1.10 | wfDs1E1PortAcceptLoopbackRequest | 0 | 0 | The DS1E1 link module is capable of detecting loop up and loop down codes received from the far end. This parameter enables and … |
| 1.3.6.1.4.1.18.3.4.9.3.1.11 | wfDs1E1PortLoopbackState | 0 | 0 | Indicates the current loopback state of this interface. The interface can be in one the following states: Payload Loopback Line Lo… |
| 1.3.6.1.4.1.18.3.4.9.3.1.12 | wfDs1E1PortBertMode | 0 | 0 | An option to generate and analyze specific test patterns is provided in BERT mode of operation. Only one port can be in BERT mode… |
| 1.3.6.1.4.1.18.3.4.9.3.1.13 | wfDs1E1PortBertTestPattern | 0 | 0 | When a port is in BERT mode, it is capable of generating a set of known patterns. This paramater selects between those patterns |
| 1.3.6.1.4.1.18.3.4.9.3.1.14 | wfDs1E1PortBertSendAlarm | 0 | 0 | Specifies a Alarm Indication Signal (AIS) (Blue Alarm) or yellow alarm to be transmitted while in BERT mode. |
| 1.3.6.1.4.1.18.3.4.9.3.1.15 | wfDs1E1PortInternationalBit | 0 | 0 | Specifies if the International bit should be set in the E1 frame |
| 1.3.6.1.4.1.18.3.4.9.3.1.17 | wfDs1E1PortLoggingEnableMask | 0 | 0 | Specifies which catagories of extended event log messages are enabled for logging. Current bit definitions are: bit 31 … |
| 1.3.6.1.4.1.18.3.4.9.3.1.18 | wfDs1E1PortSendPrmCrAddressBit | 0 | 0 | Specifies the Performance message as originating from either a Carrier or Customer Installation (CI). As the performance message… |
| 1.3.6.1.4.1.18.3.4.9.3.1.19 | wfDs1E1PortAcceptPrmCrAddressBit | 0 | 0 | Accepts only Performance messages originating from either a Carrier or Customer Installation (CI), as determined below. The PRM O… |
| 1.3.6.1.4.1.18.3.4.9.3.1.20 | wfDs1E1PortLineImpedanceOption | 0 | 0 | Supports user selectible Line Impedance option for ASN MCE1 Net Modules. |
| 1.3.6.1.4.1.18.3.4.9.3.1.21 | wfDs1E1PortFdlLoopInterframeFill | 0 | 0 | Enables the Loop Retention Interframe Time Fill for the FDL after sending Loop Up Code. Also enables the detection of the Loop R… |
| 1.3.6.1.4.1.18.3.4.9.3.1.22 | wfDs1E1PortRelayCtrl | 0 | 0 | The Relay on the QMCT1 will always be placed into loopback for the following conditions: 1. Power Up 2. Reboot 3. Hardware Reset Bu… |
| 1.3.6.1.4.1.18.3.4.9.3.1.23 | wfDs1E1PortRelayStatus | 0 | 0 | This attribute indicates the current state of the Relay on the QMCT1. When set to loop (1), the Relay is currently looping data … |
| 1.3.6.1.4.1.18.3.4.9.3.1.24 | wfDs1E1PortPrimaryClockSource | 0 | 0 | Selects the Primary source of the Tx Clock for the DS1/E1 interface |
| 1.3.6.1.4.1.18.3.4.9.3.1.25 | wfDs1E1PortSecondaryClockSource | 0 | 0 | Selects the Secondary source of the Tx Clock for the DS1/E1 interface |
| 1.3.6.1.4.1.18.3.4.9.3.1.26 | wfDs1E1PortCurrentClock | 0 | 0 | Indicates the clock source currently in use by the DS1 |
| 1.3.6.1.4.1.18.3.4.9.3.1.27 | wfDs1E1PortExtClockOperational | 0 | 0 | Indicates whether the External clock is operational |
| 1.3.6.1.4.1.18.3.4.9.3.1.28 | wfDs1E1PortTransmitWaveform | 0 | 0 | Specifies T1 transmit waveform settings. Legal values are: long haul (LBO 0.0dB) long haul (LBO 7.5dB) long haul (LBO 15.0dB) long… |