This object indicates the Holdtime interval of intelligent timer for OSPF to
perform the SPF calculation. After an intelligent timer is enabled, the
interval for the SPF calculation is as follows: The initial interval for
the SPF calculation is specified by the parameter start-interval. The
interval for the SPF calculation for the nth (n>2) time is equal to
hold-interval*2(n-1). When the interval specified by hold-interval*2(n-1)
reaches the maximum interval specified by max-interval, OSPF performs the
SPF calculation at the maximum interval for three consecutive times. Then,
OSPF performs the SPF calculation at the initial interval specified by
start-interval. When hwOspfv2SpfSchHoldIntvl is specified, you need also
specify hwOspfv2SpfSchMaxIntvl and hwOspfv2SpfSchStartIntvl, but you cannot
specify hwOspfv2SpfSchIntvlUnit or hwOspfv2SpfSchIntvlNumber. Note that -1
is not a configurable value. Instead, by set the intelligent timer to default
value, it will get back to default configuration.
Parsed from file HUAWEI-OSPFV2-MIB.mib.txt
Company: huawei
Module: HUAWEI-OSPFV2-MIB
hwOspfv2SpfSchHoldIntvl OBJECT-TYPE SYNTAX Integer32 (-1 | 1..5000) UNITS "millionSecond" MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the Holdtime interval of intelligent timer for OSPF to perform the SPF calculation. After an intelligent timer is enabled, the interval for the SPF calculation is as follows: The initial interval for the SPF calculation is specified by the parameter start-interval. The interval for the SPF calculation for the nth (n>2) time is equal to hold-interval*2(n-1). When the interval specified by hold-interval*2(n-1) reaches the maximum interval specified by max-interval, OSPF performs the SPF calculation at the maximum interval for three consecutive times. Then, OSPF performs the SPF calculation at the initial interval specified by start-interval. When hwOspfv2SpfSchHoldIntvl is specified, you need also specify hwOspfv2SpfSchMaxIntvl and hwOspfv2SpfSchStartIntvl, but you cannot specify hwOspfv2SpfSchIntvlUnit or hwOspfv2SpfSchIntvlNumber. Note that -1 is not a configurable value. Instead, by set the intelligent timer to default value, it will get back to default configuration." DEFVAL { 1000 } ::= { hwOspfv2ProcessEntry 28 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.5.25.155.3.1.1 | hwOspfv2ProcessIdIndex | 0 | 0 | The process ID indicates the OSPF process number. The value ranges from 1 to 65535. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.2 | hwOspfv2VpnName | 0 | 0 | The name of VPN instance to which the process belongs. The process instance needs to be specified when the process is created, an… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.3 | hwOspfv2ConfigRouterId | 0 | 0 | A 32-bit integer uniquely identifies the router in the Autonomous System. OSPF private router ID can be configured through this … |
| 1.3.6.1.4.1.2011.5.25.155.3.1.4 | hwOspfv2ActualRouterId | 0 | 0 | This node is used to get actual router ID of process and it is a read-only node. If the node hwOspfv2ConfigRouterId is not set, … |
| 1.3.6.1.4.1.2011.5.25.155.3.1.5 | hwOspfv2BandwidthReference | 0 | 0 | The reference value that is used to calculate the link cost. If there is no explicit link cost, OSPF calculates the cost accordi… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.6 | hwOspfv2Description | 0 | 0 | The description of the OSPF process. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.7 | hwOspfv2LsaArriveIntvl | 0 | 0 | To avoid wasting network resources due to network changes, OSPF defines that the interval for receiving LSAs is 1 second. In a st… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.8 | hwOspfv2LsaArriveMaxIntvl | 0 | 0 | This object indicates the maximum interval of intelligent-timer for receiving OSPF LSAs. When hwOspfv2LsaArriveMaxIntvl is speci… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.9 | hwOspfv2LsaArriveStartIntvl | 0 | 0 | This object indicates the initial interval of intelligent-timer for receiving OSPF LSAs. When hwOspfv2LsaArriveStartIntvl is spe… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.10 | hwOspfv2LsaArriveHoldIntvl | 0 | 0 | This object indicates the Holdtime interval of intelligent-timer for receiving OSPF LSAs. After an intelligent timer is enabled,… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.11 | hwOspfv2LsaOrigIntvl | 0 | 0 | To avoid wasting network source due to network changes, OSPF defines that the interval for updating LSAs is 5 seconds. In a stabl… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.12 | hwOspfv2LsaOrigMaxIntvl | 0 | 0 | This object indicates the maximum interval of intelligent-timer for updating OSPF LSAs. When hwOspfv2LsaOrigMaxIntvl is specifie… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.13 | hwOspfv2LsaOrigStartIntvl | 0 | 0 | This object indicates the initial interval of intelligent-timer for updating OSPF LSAs. When hwOspfv2LsaOrigStartIntvl is specif… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.14 | hwOspfv2LsaOrigHoldIntvl | 0 | 0 | This object indicates the Holdtime interval of intelligent-timer for updating OSPF LSAs. After an intelligent timer is enabled, … |
| 1.3.6.1.4.1.2011.5.25.155.3.1.15 | hwOspfv2LsaOrigIntvlOtherType | 0 | 0 | This object indicates the interval for updating LSAs, excluding OSPF router LSAs and network LSAs. hwOspfv2LsaOrigIntvlOtherType… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.16 | hwOspfv2LsdbOverflowLimit | 0 | 0 | The maximum number of external LSAs in OSPF LSDB. When this node is set to 0, it means that no limits exist. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.17 | hwOspfv2MaxLoadBalaNumber | 0 | 0 | The maximum number of equal-cost routes to a destination in the routing table. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.18 | hwOspfv2AseRouteMaxNumber | 0 | 0 | The maximum number of ASE routes that are supported by OSPF. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.19 | hwOspfv2InterRouteMaxNumber | 0 | 0 | The maximum number of inter-area routes that are supported by OSPF. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.20 | hwOspfv2IntraRouteMaxNumber | 0 | 0 | The maximum number of intra-area routes that are supported by OSPF. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.21 | hwOspfv2RetransLimitMaxNumber | 0 | 0 | The maximum count of retransmission. The value is an integer that ranges from 2 to 255. When the retransmission limit is disable… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.22 | hwOspfv2Rfc1583Compatibility | 0 | 0 | It is used to enable the routing rule for compatible RFC 1583. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.23 | hwOspfv2ShamHello | 0 | 0 | It is used to enable the sham-hello feature of OSPF. After the feature is enabled, OSPF updates the timeout timer of the neighbo… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.24 | hwOspfv2SpfSchIntvlUnit | 0 | 0 | The value of the object identifies the interval unit for OSPF to calculate routes. This object must be specified together with h… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.25 | hwOspfv2SpfSchIntvlNumber | 0 | 0 | The value of the object identifies the interval for OSPF to calculate routes. This object must be specified together with hwOspf… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.26 | hwOspfv2SpfSchMaxIntvl | 0 | 0 | This object indicates the maximum interval of intelligent timer for OSPF to perform the SPF calculation. When hwOspfv2SpfSchMaxI… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.27 | hwOspfv2SpfSchStartIntvl | 0 | 0 | This object indicates the initial interval of intelligent timer for OSPF to perform the SPF calculation. When hwOspfv2SpfSchStar… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.29 | hwOspfv2OpaqueCapability | 0 | 0 | It is used to enable opaque-LSAs capability. When the capability is enabled, then the OSPF process can generate opaque LSAs and … |
| 1.3.6.1.4.1.2011.5.25.155.3.1.30 | hwOspfv2TrafficAdjustment | 0 | 0 | It is used to enable IGP-shortcut feature. The value false means disable. Otherwise, the value true means enable. If you want to… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.31 | hwOspfv2TrafficAdvertise | 0 | 0 | It is used to enable IGP-shortcut and Forwarding Adjacency feature. |
| 1.3.6.1.4.1.2011.5.25.155.3.1.32 | hwOspfv2FlushTimer | 0 | 0 | The value of the flush timer. When configuring or undoing OSPF process, flush self-originated LSAs first. If the timer expires, s… |
| 1.3.6.1.4.1.2011.5.25.155.3.1.33 | hwOspfv2ProcessRowStatus | 0 | 0 | This node is used to create and destroy rows. Because CreateAndWait is not supported, you can set this node to CreatAndGo to crea… |