This object provides a Modem Initialization String input which will be
used to initialize a modem to the proper configuration. These are the
minimum amount of parameters required:
Auto answer
number of rings
Baud Rate
Auto Detection method of Baud rate connection string if supported
by the modem is recommended
The default string is the following:
AT&FX1E0Q0V1&C1S0=1S12=5
DURABLE.
Parsed from file Compaq-Mdc100.mib.txt
Company: compaq
Module: NETWORTH-FastEthernet-MDC100-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
mdcModemInitString OBJECT-TYPE SYNTAX DisplayString (SIZE (1..40)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides a Modem Initialization String input which will be used to initialize a modem to the proper configuration. These are the minimum amount of parameters required: Auto answer number of rings Baud Rate Auto Detection method of Baud rate connection string if supported by the modem is recommended The default string is the following: AT&FX1E0Q0V1&C1S0=1S12=5 DURABLE." ::= { mdcModuleInfo 22 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.215.1.1.7.2.22.0 | mdcModemInitString | 0 | 0 | None |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.215.1.1.7.2.1 | mdcThisAgent | 1 | 1 | The position of the MDC in this stack of units. Note that the top unit in the stack is unit #1 |
1.3.6.1.4.1.215.1.1.7.2.2 | mdcPreBootMajorVer | 1 | 1 | The major number of the Pre-Boot Flash Block version. For example, if the firmware version is 2.12, the value of this object wou… |
1.3.6.1.4.1.215.1.1.7.2.3 | mdcPreBootMinorVer | 1 | 1 | The minor number of the Pre-Boot Flash Block version. For example, if the firmware version is 2.12, the value of this object wou… |
1.3.6.1.4.1.215.1.1.7.2.4 | mdcBootMajorVer | 1 | 1 | The major number of the Boot Block Flash version. For example, if the firmware version is 2.12, the value of this object would b… |
1.3.6.1.4.1.215.1.1.7.2.5 | mdcBootMinorVer | 1 | 1 | The minor number of the Boot Flash Block version. For example, if the firmware version is 2.12, the value of this object would b… |
1.3.6.1.4.1.215.1.1.7.2.6 | mdcRuntimeMajorVer | 1 | 1 | The major number of the Runtime Flash Block version. For example, if the firmware version is 2.12, the value of this object woul… |
1.3.6.1.4.1.215.1.1.7.2.7 | mdcRuntimeMinorVer | 1 | 1 | The minor number of the Runtime Flash Block version. For example, if the firmware version is 2.12, the value of this object woul… |
1.3.6.1.4.1.215.1.1.7.2.8 | mdcBootWriteCycles | 1 | 1 | This object will allow the user to see the number of erase/writes that have been made to the Boot block on the FLASH PROM chip. |
1.3.6.1.4.1.215.1.1.7.2.9 | mdcRuntimeWriteCycles | 1 | 1 | This object will allow the user to see the number of erase/writes that have been made to the RunTime block on the FLASH PROM chi… |
1.3.6.1.4.1.215.1.1.7.2.10 | mdcWriteCommunity | 1 | 1 | The write community name for the Management Agent. If the value is not public, the write community name is not returned for get … |
1.3.6.1.4.1.215.1.1.7.2.11 | mdcWriteProtect | 1 | 1 | When set to ro(2), all supported MIB objects, with the exception of this object are made read only. This may be used in conjunct… |
1.3.6.1.4.1.215.1.1.7.2.12 | mdcIPFrameType | 1 | 1 | Except when booting up, a hub will communicate over IP using a single frame type defining the type of network that the IP traffi… |
1.3.6.1.4.1.215.1.1.7.2.13 | mdcIPXFrameType | 1 | 1 | The frame type over which IPX communication originating from the MDC100 will take place. The unit will respond to a packet using… |
1.3.6.1.4.1.215.1.1.7.2.14 | mdcIPXSAPBroadcast | 1 | 1 | The hub will generate SAP broadcasts over IPX. This allows the hub to be auto-discovered by Novell's NMS and is used to generat… |
1.3.6.1.4.1.215.1.1.7.2.15 | mdcIPAutoDiscoveryState | 1 | 1 | This object will allow a user to enable the unit to send out periodic ICMP Pings to ensure that the unit's IP Address is contain… |
1.3.6.1.4.1.215.1.1.7.2.16 | mdcPingPacketRate | 1 | 1 | This object will determine the rate (in seconds) at which ICMP Pings will be sent out by the unit to ensure that its IP Address … |
1.3.6.1.4.1.215.1.1.7.2.17 | mdcBootpRarpRetries | 1 | 1 | This object will allow the user to set the number of BOOTP/RARP retries that will be performed when the unit goes through its Bo… |
1.3.6.1.4.1.215.1.1.7.2.18 | mdcBootpRarpRetryInterval | 1 | 1 | This object will allow the user to set the time period (in seconds) after which a BOOTP/RARP attempt will time out and the unit … |
1.3.6.1.4.1.215.1.1.7.2.19 | mdcBootpRarpRequests | 1 | 1 | This object allows the user to enable/disable generation of BOOTP/RARP requests from the Hub in BOTH Boot and RunTime code. In B… |
1.3.6.1.4.1.215.1.1.7.2.20 | mdcVT100ScreenRefresh | 1 | 1 | This object will determine the rate, in seconds, at which the VT100 screen will refresh (i.e, update) the automatic fields (e.g.… |
1.3.6.1.4.1.215.1.1.7.2.21 | mdcRptrReset | 1 | 1 | Setting this object to reset(2) causes the unit to reset the management agent but retains the counter values. All non-durable in… |
1.3.6.1.4.1.215.1.1.7.2.23 | mdcModemAutoNegotiateState | 1 | 1 | If enabled(1), then the MDC100 will adjust its speed to that specified when the modem answers the incoming connection. If the mo… |