wvInsertTestSignalLine OBJECT-TYPE
SYNTAX BITS {
filler0 (0),
dsx1-1 (1), -- e1/t1 port 1
dsx1-2 (2), -- e1/t1 port 2
dsx1-3 (3), -- e1/t1 port 3
dsx1-4 (4), -- e1/t1 port 4
dsx1-5 (5), -- e1/t1 port 5
dsx1-6 (6), -- e1/t1 port 6
dsx1-7 (7), -- e1/t1 port 7
dsx1-8 (8), -- e1/t1 port 8
dsx1-9 (9), -- e1/t1 port 9
dsx1-10 (10), -- e1/t1 port 10
dsx1-11 (11), -- e1/t1 port 11
dsx1-12 (12), -- e1/t1 port 12
dsx1-13 (13), -- e1/t1 port 13
dsx1-14 (14), -- e1/t1 port 14
dsx1-15 (15), -- e1/t1 port 15
dsx1-16 (16), -- e1/t1 port 16
dsx3 (17), -- e3/t3 port
eth10-100 (18) -- ETH 10/100
}
MAX-ACCESS read-write
DESCRIPTION
"Defines the line(s) on which a special BER test signal is inserted.
Proper loopbacks are assumed to be previously set for the test to succeed.
If no loopback is selected, the test results are checked at the peer terminal.
The actual lines applicable depend on wvLinkCapacity.
In addition, only the following combinations can be simultaneously tested:
- 1 T1/E1 line
- T3/E3 line
- the eth10-100 board (both ports)
- all existing lines/ports (full capacity)."
View at oid-info.com
Defines the line(s) on which a special BER test signal is inserted.
Proper loopbacks are assumed to be previously set for the test to succeed.
If no loopback is selected, the test results are checked at the peer terminal.
The actual lines applicable depend on wvLinkCapacity.
In addition, only the following combinations can be simultaneously tested:
- 1 T1/E1 line
- T3/E3 line
- the eth10-100 board (both ports)
- all existing lines/ports (full capacity).
Parsed from file 8800-DMR.txt
Company: None
Module: CODAN-MIB
Defines the line(s) on which a special BER test signal is inserted.
Proper loopbacks are assumed to be previously set for the test to succeed.
If no loopback is selected, the test results are checked at the peer terminal.
The actual lines applicable depend on wvLinkCapacity.
In addition, only the following combinations can be simultaneously tested:
- 1 T1/E1 line
- T3/E3 line
- the eth10-100 board (both ports)
- all existing lines/ports (full capacity).
Parsed from file CODAN-MIB.mib
Module: CODAN-MIB
wvInsertTestSignalLine OBJECT-TYPE SYNTAX BITS { filler0(0), dsx1-1(1), dsx1-2(2), dsx1-3(3), dsx1-4(4), dsx1-5(5), dsx1-6(6), dsx1-7(7), dsx1-8(8), dsx1-9(9), dsx1-10(10), dsx1-11(11), dsx1-12(12), dsx1-13(13), dsx1-14(14), dsx1-15(15), dsx1-16(16), dsx3(17), eth10-100(18) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the line(s) on which a special BER test signal is inserted. Proper loopbacks are assumed to be previously set for the test to succeed. If no loopback is selected, the test results are checked at the peer terminal. The actual lines applicable depend on wvLinkCapacity. In addition, only the following combinations can be simultaneously tested: - 1 T1/E1 line - T3/E3 line - the eth10-100 board (both ports) - all existing lines/ports (full capacity)." ::= { wvTests 200 }
wvInsertTestSignalLine OBJECT-TYPE SYNTAX BITS { filler0(0), dsx1-1(1), dsx1-2(2), dsx1-3(3), dsx1-4(4), dsx1-5(5), dsx1-6(6), dsx1-7(7), dsx1-8(8), dsx1-9(9), dsx1-10(10), dsx1-11(11), dsx1-12(12), dsx1-13(13), dsx1-14(14), dsx1-15(15), dsx1-16(16), dsx3(17), eth10-100(18) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the line(s) on which a special BER test signal is inserted. Proper loopbacks are assumed to be previously set for the test to succeed. If no loopback is selected, the test results are checked at the peer terminal. The actual lines applicable depend on wvLinkCapacity. In addition, only the following combinations can be simultaneously tested: - 1 T1/E1 line - T3/E3 line - the eth10-100 board (both ports) - all existing lines/ports (full capacity)." ::= { wvTests 200 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.23304.1.1.4.200.0 | wvInsertTestSignalLine | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.23304.1.1.4.1 | wvLoopbackType | 1 | 1 | Defines the type of loopback to be performed on the terminal. |
| 1.3.6.1.4.1.23304.1.1.4.2 | wvLoopbackStartTime | 1 | 1 | Defines the desired delay time, in time-ticks, before the loopbacks specified by wvLoopbackType are activated. When any loopback … |
| 1.3.6.1.4.1.23304.1.1.4.3 | wvLoopbackTimePeriod | 1 | 1 | Defines the desired duration of the loopback. Setting a value of 0 means it should run until deliberately stopped. |
| 1.3.6.1.4.1.23304.1.1.4.4 | wvLoopbackRemainingStartTime | 1 | 1 | Defines the ongoing remaining time before the loopbacks specified by wvLoopbackType are activated. |
| 1.3.6.1.4.1.23304.1.1.4.5 | wvLoopbackRemainingTimePeriod | 1 | 1 | Defines the ongoing remaining duration of the loopback activation. |
| 1.3.6.1.4.1.23304.1.1.4.100 | wvSelfTestType | 1 | 1 | Defines the type of next self-tests to be performed on the terminal. Local restrictions may limit the tests that can be performe… |
| 1.3.6.1.4.1.23304.1.1.4.101 | wvSelfTestStartTime | 1 | 1 | Defines the desired delay time, in time-ticks, before the tests specified by wvSelfTestType are started. When any test is running… |
| 1.3.6.1.4.1.23304.1.1.4.102 | wvLastSelfTestStartTime | 1 | 1 | Keeps the time, relative to sysUpTime, when the tests in the wvLastSelfTestTable were last performed. |
| 1.3.6.1.4.1.23304.1.1.4.103 | wvLastSelfTestTable | 1 | 3 | wvLastSelftestTable |
| 1.3.6.1.4.1.23304.1.1.4.104 | wvSelfTestRemainingStartTime | 1 | 1 | Defines the ongoing remaining time before the tests specified by wvSelfTestType start. |
| 1.3.6.1.4.1.23304.1.1.4.201 | wvInsertTestSignalStartTime | 1 | 1 | Defines the desired delay time, in time-ticks, before the tests on the lines specified by wvInsertTestSignalLine are started. Whe… |
| 1.3.6.1.4.1.23304.1.1.4.202 | wvInsertTestSignalTimePeriod | 1 | 1 | Defines the desired duration of the tests. Setting a value of 0 means it should run until deliberately stopped. |
| 1.3.6.1.4.1.23304.1.1.4.203 | wvLastTestSignalTime | 1 | 1 | Defines the time, relative to sysUpTime, when the insert test signal was last performed. |
| 1.3.6.1.4.1.23304.1.1.4.204 | wvLastTestSignalBER | 1 | 1 | Specifies the Bit Error Rate from last test signal activation. |
| 1.3.6.1.4.1.23304.1.1.4.205 | wvInsertTestSignalRemainingStartTime | 1 | 1 | Defines the ongoing remaining time before the tests on the lines specified by wvInsertTestSignalLine start. |
| 1.3.6.1.4.1.23304.1.1.4.206 | wvInsertTestSignalRemainingTimePeriod | 1 | 1 | Defines the ongoing remaining duration of the tests. |
| 1.3.6.1.4.1.23304.1.1.4.300 | wvGenericDiagnosticsParameterAddress | 1 | 1 | This object defines the address on the IDU physical memory from which wvGenericDiagnosticsParameterValue below is read. The given… |
| 1.3.6.1.4.1.23304.1.1.4.301 | wvGenericDiagnosticsParameterValue | 1 | 1 | Reading of this object returns the 4 bytes (long) value on the address specified by wvGenericDiagnosticsParameterAddress above. |