Far end sending Alarm Indication Signal(AIS) a.k.a Remote
Alarm Indication (RAI).
For D4 and ESF links, the 'all ones' condition is detected at
a DS1 line interface upon observing an unframed signal with a
one's density of at least 99.9% present for a time equal to or
greater than T, where 3 ms <= T <= 75 ms. The AIS is
terminated upon observing a signal not meeting the one's
density or the unframed signal criteria for a period equal to
or greater than than T. (See G.775, Section 5.4)
For E1 links, the 'all-ones' condition is detected at the line
interface as a string of 512 bits containing fewer than three
zero bits (see O.162 [12] Section 3.3.2).
Parsed from file mariposa.mib.txt
Company: marconi
Module: MARIPOSA-MIB
Vendor: Marconi
Module: MARIPOSA-MIB (mariposa.mib)
Type: TABULAR
Access: read-only
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
cbrPhyAISFState OBJECT-TYPE SYNTAX INTEGER { yes (1), no (2) } ACCESS read-only STATUS mandatory DESCRIPTION "Far end sending Alarm Indication Signal(AIS) a.k.a Remote Alarm Indication (RAI). For D4 and ESF links, the 'all ones' condition is detected at a DS1 line interface upon observing an unframed signal with a one's density of at least 99.9% present for a time equal to or greater than T, where 3 ms <= T <= 75 ms. The AIS is terminated upon observing a signal not meeting the one's density or the unframed signal criteria for a period equal to or greater than than T. (See G.775, Section 5.4) For E1 links, the 'all-ones' condition is detected at the line interface as a string of 512 bits containing fewer than three zero bits (see O.162 [12] Section 3.3.2)." ::= { cbrPhyEntry 19 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.1 | cbrPhyIfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.2 | cbrPhyLinkEnable | 0 | 0 | This object is used to enable and disable link. This Object is an Obsolete Object |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.3 | cbrPhyCurrentLineType | 0 | 0 | This object indicates the type of the line implementing this circuit. It defines the link type that is currently active in the sy… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.4 | cbrPhyStoredLineType | 0 | 0 | This object indicates the type of the line implementing this circuit that is saved in the flash. When the value of this object … |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.5 | cbrPhyCurrentFraming | 0 | 0 | This object indicates the framing type that is used for this circuit. It defines the framing type that is currently active in the… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.6 | cbrPhyStoredFraming | 0 | 0 | This object indicates the framing type that is used for this circuit. It defines the framing type that is currently active in the… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.7 | cbrPhyCurrentLineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression that is currently used on this interface, which in turn affects a nu… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.8 | cbrPhyStoredLineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression of this interface that is saved in the flash. When the value of this… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.9 | cbrPhyLineLength | 0 | 0 | The length of the ds1 line in meters. This objects provides information for line build out circuitry if it exists and can use thi… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.10 | cbrPhyTxClockSource | 0 | 0 | The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'SystemTiming… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.11 | cbrPhyLoopbackMode | 0 | 0 | This variable represents the desired loopback configuration of the interface. Agents supporting read/write access should return b… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.12 | cbrPhySignalingMode | 0 | 0 | This object specifies signaling mode for CBR link. This can have CCS mode, CAS mode, CES Basic mode or CES with CAS, CAS Without … |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.13 | cbrPhyTimeElapsed | 0 | 0 | The number of seconds that have elapsed since the beginning of the near end current error- measurement period. This Object is Obs… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.14 | cbrPhyValidIntervals | 0 | 0 | The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brou… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.15 | cbrPhyLossOfSignalState | 0 | 0 | Near end Loss Of Signal. When cells are continuously lost the value is set to loss (2). When cells are no longer lost, the value … |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.16 | cbrPhyLossOfFrameState | 0 | 0 | Near end LOF (a.k.a., Red Alarm). For DS1 links, the Loss Of Frame failure is declared when an OOF or LOS defect has persisted fo… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.17 | cbrPhyXmtFarEndLOFFState | 0 | 0 | Near End is sending the LOF indication. |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.18 | cbrPhyRcvFarEndLOFFState | 0 | 0 | The Far End LOF failure Alarm is also known as Yellow Alarm in the DS1 case, and Distant Alarm in the E1 case. For D4 links, the F… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.20 | cbrPhyXmtAISFState | 0 | 0 | Near end sending Alarm Indication Signal(AIS). For D4 and ESF links, the 'all ones' condition is detected at a DS1 line interface… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.21 | cbrPhyAlarmReporting | 0 | 0 | This object identifies the Alarm Reporting of the cbr voice. |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.22 | cbrPhyVoiceCompanding | 0 | 0 | This object specifies the channel the voice companding technique - either A-law or mode. |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.23 | cbrPhySystemClockSource | 0 | 0 | This object identifies the System Clock Source. It can be 1.Internal 2.ATM 3.CBR |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.24 | cbrPhySystemClockSourceStatus | 0 | 0 | This objects specifies whether the clock source defined by 'systemClockSource' is refering to a valid resource or not. If the spe… |