The length of the ds1 line in meters. This
objects provides information for line build out
circuitry if it exists and can use this object to
adjust the line build out. It can have one of the
defined ranges:
1) feet-0-115-meters-0-35: 0 to 115 feet
0 to 35 meters,
2) feet-82-213-meters-25-65: 82 to 312 feet
25 to 65 meters,
3) feet-180-312-meters-55-95: 180 to 312 feet
55 to 95 meters,
4) feet-279-410-meters-85-125: 279 to 410 feet
85 to 125 meters,
5) feet-377-509-meters-115-155: 377 to 509 feet
115 to 155 meters,
6) feet-476-607-meters-145-185: 476 to 607 feet
145 to 185 meters,
7) feet-574-689-meters-175-210: 574 to 689 feet
175 to 210 meters,
8) feet-689-up-meters-210-up: more than 689 feet
more than 210 meters.
Parsed from file mariposa.mib.txt
Company: marconi
Module: MARIPOSA-MIB
Vendor: Marconi
Module: MARIPOSA-MIB (mariposa.mib)
Type: TABULAR
Access: read-only
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
cbrPhyLineLength OBJECT-TYPE SYNTAX INTEGER { feet-0-115-meters-0-35 (1), feet-82-213-meters-25-65 (2), feet-180-312-meters-55-95 (3), feet-279-410-meters-85-125 (4), feet-377-509-meters-115-155 (5), feet-476-607-meters-145-185 (6), feet-574-689-meters-175-210 (7), feet-689-up-meters-210-up (8) } ACCESS read-only STATUS mandatory DESCRIPTION "The length of the ds1 line in meters. This objects provides information for line build out circuitry if it exists and can use this object to adjust the line build out. It can have one of the defined ranges: 1) feet-0-115-meters-0-35: 0 to 115 feet 0 to 35 meters, 2) feet-82-213-meters-25-65: 82 to 312 feet 25 to 65 meters, 3) feet-180-312-meters-55-95: 180 to 312 feet 55 to 95 meters, 4) feet-279-410-meters-85-125: 279 to 410 feet 85 to 125 meters, 5) feet-377-509-meters-115-155: 377 to 509 feet 115 to 155 meters, 6) feet-476-607-meters-145-185: 476 to 607 feet 145 to 185 meters, 7) feet-574-689-meters-175-210: 574 to 689 feet 175 to 210 meters, 8) feet-689-up-meters-210-up: more than 689 feet more than 210 meters." ::= { cbrPhyEntry 9 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.1 | cbrPhyIfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.2 | cbrPhyLinkEnable | 0 | 0 | This object is used to enable and disable link. This Object is an Obsolete Object |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.3 | cbrPhyCurrentLineType | 0 | 0 | This object indicates the type of the line implementing this circuit. It defines the link type that is currently active in the sy… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.4 | cbrPhyStoredLineType | 0 | 0 | This object indicates the type of the line implementing this circuit that is saved in the flash. When the value of this object … |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.5 | cbrPhyCurrentFraming | 0 | 0 | This object indicates the framing type that is used for this circuit. It defines the framing type that is currently active in the… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.6 | cbrPhyStoredFraming | 0 | 0 | This object indicates the framing type that is used for this circuit. It defines the framing type that is currently active in the… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.7 | cbrPhyCurrentLineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression that is currently used on this interface, which in turn affects a nu… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.8 | cbrPhyStoredLineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression of this interface that is saved in the flash. When the value of this… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.10 | cbrPhyTxClockSource | 0 | 0 | The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'SystemTiming… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.11 | cbrPhyLoopbackMode | 0 | 0 | This variable represents the desired loopback configuration of the interface. Agents supporting read/write access should return b… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.12 | cbrPhySignalingMode | 0 | 0 | This object specifies signaling mode for CBR link. This can have CCS mode, CAS mode, CES Basic mode or CES with CAS, CAS Without … |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.13 | cbrPhyTimeElapsed | 0 | 0 | The number of seconds that have elapsed since the beginning of the near end current error- measurement period. This Object is Obs… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.14 | cbrPhyValidIntervals | 0 | 0 | The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brou… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.15 | cbrPhyLossOfSignalState | 0 | 0 | Near end Loss Of Signal. When cells are continuously lost the value is set to loss (2). When cells are no longer lost, the value … |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.16 | cbrPhyLossOfFrameState | 0 | 0 | Near end LOF (a.k.a., Red Alarm). For DS1 links, the Loss Of Frame failure is declared when an OOF or LOS defect has persisted fo… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.17 | cbrPhyXmtFarEndLOFFState | 0 | 0 | Near End is sending the LOF indication. |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.18 | cbrPhyRcvFarEndLOFFState | 0 | 0 | The Far End LOF failure Alarm is also known as Yellow Alarm in the DS1 case, and Distant Alarm in the E1 case. For D4 links, the F… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.19 | cbrPhyAISFState | 0 | 0 | Far end sending Alarm Indication Signal(AIS) a.k.a Remote Alarm Indication (RAI). For D4 and ESF links, the 'all ones' condition … |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.20 | cbrPhyXmtAISFState | 0 | 0 | Near end sending Alarm Indication Signal(AIS). For D4 and ESF links, the 'all ones' condition is detected at a DS1 line interface… |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.21 | cbrPhyAlarmReporting | 0 | 0 | This object identifies the Alarm Reporting of the cbr voice. |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.22 | cbrPhyVoiceCompanding | 0 | 0 | This object specifies the channel the voice companding technique - either A-law or mode. |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.23 | cbrPhySystemClockSource | 0 | 0 | This object identifies the System Clock Source. It can be 1.Internal 2.ATM 3.CBR |
1.3.6.1.4.1.2426.1.2.6.2.1.1.1.1.24 | cbrPhySystemClockSourceStatus | 0 | 0 | This objects specifies whether the clock source defined by 'systemClockSource' is refering to a valid resource or not. If the spe… |