The number of LMI STATUS frames received from the DCE since the
last system reset. The count includes link integrity
verification frames only.
Parsed from file cascade.mib.txt
Company: None
Module: CASCADE-MIB
The number of LMI STATUS frames received from the DCE since the
last system reset. The count includes link integrity
verification frames only.
Parsed from file CASCADE-MIB.mib
Module: CASCADE-MIB
Vendor: Cascade Communications Corp.
Module: CASCADE-MIB
[Automatically extracted from oidview.com]
lportDTEInStatusFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of LMI STATUS frames received from the DCE since the last system reset. The count includes link integrity verification frames only." ::= { lportEntry 52 }
lportDTEInStatusFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of LMI STATUS frames received from the DCE since the last system reset. The count includes link integrity verification frames only." ::= { lportEntry 52 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.277.1.5.1.1.2 | lportSlotId | 0 | 0 | The slot number of the board the port is on. |
| 1.3.6.1.4.1.277.1.5.1.1.3 | lportPportId | 0 | 0 | The physical port number of the interface on the board. |
| 1.3.6.1.4.1.277.1.5.1.1.4 | lportId | 0 | 0 | The logical port number of the interface on the physical port. A logical port can be uniquely identified in a Cascade network as… |
| 1.3.6.1.4.1.277.1.5.1.1.5 | lportLink | 0 | 0 | The equipment type of the peer to which the logical port is connected. |
| 1.3.6.1.4.1.277.1.5.1.1.6 | lportProtocol | 0 | 0 | The data link protocol running on the logical port. |
| 1.3.6.1.4.1.277.1.5.1.1.7 | lportSignal | 0 | 0 | The user-network signalling capability for SVC and DLCMI of the logical port. Note that this only applies to fr protocol port. |
| 1.3.6.1.4.1.277.1.5.1.1.8 | lportFt1Ds0s | 0 | 0 | The bit mask indicating the DS0s for the fractional T1/E1 logical port which must be a subset of the corresponding pportDs1Ds0s. … |
| 1.3.6.1.4.1.277.1.5.1.1.9 | lportGlobalDlci | 0 | 0 | The global DLCI correspondent to the interface if the DLCI is globally significant in the network. Note that this object is read-… |
| 1.3.6.1.4.1.277.1.5.1.1.10 | lportDlcmiStd | 0 | 0 | This variable states which Data Link Connection Management scheme is active (and by implication, what DLCI it uses) on the Fram… |
| 1.3.6.1.4.1.277.1.5.1.1.11 | lportDlciAddrFmt | 0 | 0 | This variable states which address format is in use on the Frame Relay interface. |
| 1.3.6.1.4.1.277.1.5.1.1.12 | lportDlciAddrLen | 0 | 0 | This variable states which address length in octets. In the case of Q922 format, the length indicates the entire length of the ad… |
| 1.3.6.1.4.1.277.1.5.1.1.13 | lportMaxFramesize | 0 | 0 | The maximum frame size supported on the interface. Currently it's not used. |
| 1.3.6.1.4.1.277.1.5.1.1.14 | lportDceVerifTimer | 0 | 0 | lportDceVeriftimer |
| 1.3.6.1.4.1.277.1.5.1.1.15 | lportDceErrorThresh | 0 | 0 | The error threshold on the DCE interface. If the port is configured as a DXI/SNI, then this MIB object defines the heartbeat poll… |
| 1.3.6.1.4.1.277.1.5.1.1.16 | lportDceEventCount | 0 | 0 | The monitored events count on the DCE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.17 | lportDteErrorThresh | 0 | 0 | The error threshold on the DTE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.18 | lportDteEventCount | 0 | 0 | The monitored events count on the DTE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.19 | lportDtePollTimer | 0 | 0 | The link status polling timer (secs) on the DTE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.20 | lportDteFullCounter | 0 | 0 | The full status polling counter on the DTE interface. |
| 1.3.6.1.4.1.277.1.5.1.1.21 | lportDteMulticast | 0 | 0 | The multicast capability of the interface. |
| 1.3.6.1.4.1.277.1.5.1.1.22 | lportTrkRnode | 0 | 0 | Node at the other end of the trunk. This object is read-write only during lport creation, and read-only thereafter. |
| 1.3.6.1.4.1.277.1.5.1.1.23 | lportTrkRlport | 0 | 0 | Logical port (IfIndex) at the other end of the trunk. This |
| 1.3.6.1.4.1.277.1.5.1.1.24 | lportCongestState | 0 | 0 | Congestion State for the logical port. |
| 1.3.6.1.4.1.277.1.5.1.1.25 | lportQP1Len | 0 | 0 | Priority-1 queue length (number of packets) in xmit buffer. |
| 1.3.6.1.4.1.277.1.5.1.1.26 | lportQP2Len | 0 | 0 | Priority-2 queue length (number of packets) in xmit buffer. |
| 1.3.6.1.4.1.277.1.5.1.1.27 | lportQP3Len | 0 | 0 | Priority-3 queue length (number of packets) in xmit buffer. |
| 1.3.6.1.4.1.277.1.5.1.1.28 | lportQP4Len | 0 | 0 | Priority-4 queue length (number of packets) in xmit buffer. |
| 1.3.6.1.4.1.277.1.5.1.1.29 | lportErrTime | 0 | 0 | The value of sysUpTime at which the last error was detected. |
| 1.3.6.1.4.1.277.1.5.1.1.30 | lportErrType | 0 | 0 | The type of error that was last seen on this interface. |
| 1.3.6.1.4.1.277.1.5.1.1.31 | lportErrData | 0 | 0 | An octet string containing as much of the error packet as possible. As a minimum, it must contain the Q.922 Address or as much a… |
| 1.3.6.1.4.1.277.1.5.1.1.32 | lportDiagTestId | 0 | 0 | Identification for the diagnostics tests to be run. |
| 1.3.6.1.4.1.277.1.5.1.1.33 | lportDiagTestRuns | 0 | 0 | Number of passes of the diagnostics tests to be run. The default value is 1. |
| 1.3.6.1.4.1.277.1.5.1.1.34 | lportDataRate | 0 | 0 | An estimate of the logical port's data rate in bits per second. |
| 1.3.6.1.4.1.277.1.5.1.1.35 | lportTrkStatus | 0 | 0 | The current state of the trunk. The btdefined state only applies to backup trunks. |
| 1.3.6.1.4.1.277.1.5.1.1.36 | lportSevCongests | 0 | 0 | The cumulative number of times that the lport's congestion state has changed from mildly-congested to severely-congested since th… |
| 1.3.6.1.4.1.277.1.5.1.1.37 | lportAbsCongests | 0 | 0 | The cumulative number of times that the lport's congestion state has changed from severely-congested to absolutely- congested sin… |
| 1.3.6.1.4.1.277.1.5.1.1.38 | lportTrkOverhead | 0 | 0 | An estimate of the overhead (headers and internal control messages) in trunking user data in terms of a percentage of the configu… |
| 1.3.6.1.4.1.277.1.5.1.1.39 | lportTrkUtil | 0 | 0 | An estimate of the real utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.40 | lportVAvailbw | 0 | 0 | Currently available virtual trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.41 | lportTrkLastTimeChange | 0 | 0 | The sysUpTime value when the trunk was last changed to the current status. |
| 1.3.6.1.4.1.277.1.5.1.1.42 | lportCongestRate | 0 | 0 | The rate (%) of entering severely or absolutely congested states in the last one minute interval. |
| 1.3.6.1.4.1.277.1.5.1.1.43 | lportCongestRateThresh | 0 | 0 | The alert threshold (%) for the CongestRate; trap will be sent when exceeded. |
| 1.3.6.1.4.1.277.1.5.1.1.44 | lportDiagState | 0 | 0 | The current state of the diagnostic on this logical port. |
| 1.3.6.1.4.1.277.1.5.1.1.45 | lportDiagOptionStr | 0 | 0 | Optional parameters to the diagnostic. |
| 1.3.6.1.4.1.277.1.5.1.1.46 | lportDiagPassCount | 0 | 0 | Number of successful diagnostic passes. |
| 1.3.6.1.4.1.277.1.5.1.1.47 | lportDiagFailCount | 0 | 0 | Number of failed diagnostic passes. |
| 1.3.6.1.4.1.277.1.5.1.1.48 | lportDiagResultStr | 0 | 0 | Description of last diagnostic failure. |
| 1.3.6.1.4.1.277.1.5.1.1.49 | lportDs0BitStuff | 0 | 0 | Is bit stuffing enabled on this lport? |
| 1.3.6.1.4.1.277.1.5.1.1.50 | lportErrorThreshold | 0 | 0 | The per minute error threshold before a link error trap is sent. |
| 1.3.6.1.4.1.277.1.5.1.1.51 | lportUnsyncBandwidth | 0 | 0 | The accumulated allocated/deallocated bandwidth which has not been propagated by OSPF yet. |
| 1.3.6.1.4.1.277.1.5.1.1.53 | lportDTEInFullStatusFrames | 0 | 0 | The number of LMI Full STATUS frames received from the DTE since the last system reset. |
| 1.3.6.1.4.1.277.1.5.1.1.54 | lportDTEInAsyncStatusFrames | 0 | 0 | The number of asynchronous LMI Status frames received from the DTE since the last system reset. For LMI Rev 1, these are Update S… |
| 1.3.6.1.4.1.277.1.5.1.1.55 | lportDTEInErrorFrames | 0 | 0 | The number of LMI frames received containing protocol errors. |
| 1.3.6.1.4.1.277.1.5.1.1.56 | lportDTEOutPollFrames | 0 | 0 | The number of LMI Status Enquiry frames transmitted since the last system reset. |
| 1.3.6.1.4.1.277.1.5.1.1.57 | lportDTEPollErrorCounts | 0 | 0 | The number of DTE in-channel signaling link reliability errors (i.e. LMI Status Enquiry frames that were not responded to, seque… |
| 1.3.6.1.4.1.277.1.5.1.1.58 | lportDTEFailCounts | 0 | 0 | The number of times since the last system reset LMI has declared the DTE side of the link down due to excessive errors. |
| 1.3.6.1.4.1.277.1.5.1.1.59 | lportDTEFailReason | 0 | 0 | The LMI failure reason. If the rate of LMI detected errors exceeds the threshold, this contains the cause of the most recent erro… |
| 1.3.6.1.4.1.277.1.5.1.1.60 | lportDTEOperStatus | 0 | 0 | The operational status of the DTE side of LMI on this link. |
| 1.3.6.1.4.1.277.1.5.1.1.61 | lportDCEInPollFrames | 0 | 0 | The number of LMI poll frames received from the DTE since the last system reset. |
| 1.3.6.1.4.1.277.1.5.1.1.62 | lportDCEInErrorFrames | 0 | 0 | The number of LMI frames received containing protocol errors. |
| 1.3.6.1.4.1.277.1.5.1.1.63 | lportDCEOutStatusFrames | 0 | 0 | The number of LMI STATUS frames transmitted since the last system reset. The count includes link integrity verification frames on… |
| 1.3.6.1.4.1.277.1.5.1.1.64 | lportDCEOutFullStatusFrames | 0 | 0 | The number of LMI Full STATUS frames transmitted since the last system reset. |
| 1.3.6.1.4.1.277.1.5.1.1.65 | lportDCEOutAsyncStatusFrames | 0 | 0 | The number of asynchronous LMI Status frames transmitted since the last system reset. For LMI Rev 1, these are Update STATUS fram… |
| 1.3.6.1.4.1.277.1.5.1.1.66 | lportDCEPollErrorCounts | 0 | 0 | The number of DCE in-channel signaling link reliability errors (i.e. timeouts waiting for LMI Status Enquiry frames, sequence nu… |
| 1.3.6.1.4.1.277.1.5.1.1.67 | lportDCEFailCounts | 0 | 0 | The number of times since the last system reset LMI has declared the DCE side of the link down due to excessive errors. |
| 1.3.6.1.4.1.277.1.5.1.1.68 | lportDCEFailReason | 0 | 0 | The LMI failure reason. If the rate of LMI detected errors exceeds the threshold, this contains the cause of the most recent erro… |
| 1.3.6.1.4.1.277.1.5.1.1.69 | lportDCEOperStatus | 0 | 0 | The operational status of the DCE side of LMI on this link. |
| 1.3.6.1.4.1.277.1.5.1.1.70 | lportDCEOperDlcmiStd | 0 | 0 | This variable states which Data Link Connection Management scheme is actually being run on this link. This is used for DCE links … |
| 1.3.6.1.4.1.277.1.5.1.1.71 | lportLMIInErrorFrames | 0 | 0 | The number of total frames received with an error. For NNI links this is the sum of lportDTEInErrorFrames and lportDCEInErrorFram… |
| 1.3.6.1.4.1.277.1.5.1.1.72 | lportDCEnN4 | 0 | 0 | This variable specifies the maximum number of LMI Status Enquiry frames that can be received from a DTE within time interval lpor… |
| 1.3.6.1.4.1.277.1.5.1.1.73 | lportDCEnT3 | 0 | 0 | This variable specifies the time interval (secs) used to determine if lportDCEnN4 an excess number (lportDCEnN4) of Status Enqui… |
| 1.3.6.1.4.1.277.1.5.1.1.74 | lportXmitLatencyThreshold | 0 | 0 | Outbound frames are allowed on the transmit commit queue when the commit queue falls below this threshold (in microseconds). |
| 1.3.6.1.4.1.277.1.5.1.1.75 | lportXmitRefillPriority0Percentage | 0 | 0 | Percentage of time the transmit queue is refilled in priority order 0, 1, 2, 3. |
| 1.3.6.1.4.1.277.1.5.1.1.76 | lportXmitRefillPriority1Percentage | 0 | 0 | Percentage of time the transmit queue is refilled in priority order 1, 2, 3, 0. |
| 1.3.6.1.4.1.277.1.5.1.1.77 | lportXmitRefillPriority2Percentage | 0 | 0 | Percentage of time the transmit queue is refilled in priority order 2, 3, 0, 1. |
| 1.3.6.1.4.1.277.1.5.1.1.78 | lportXmitRefillPriority3Percentage | 0 | 0 | Percentage of time the transmit queue is refilled in priority order 3, 0, 1, 2. |
| 1.3.6.1.4.1.277.1.5.1.1.79 | lportXmitDiscardLow, lportAbsoluteThreshold | 0 | 0 | Priority holding queue low water discard threshold. Discarding stops when holding queue hits this level. |
| 1.3.6.1.4.1.277.1.5.1.1.80 | lportSevereThreshold | 0 | 0 | Severe congestion level. Outbound red and amber packets are discarded when the transmit queue hits this threshold. |
| 1.3.6.1.4.1.277.1.5.1.1.81 | lportMildThreshold | 0 | 0 | Mild congestion level. Outbound red packets are discarded when the transmit queue hits this threshold. |
| 1.3.6.1.4.1.277.1.5.1.1.82 | lportAtmUPCEnable | 0 | 0 | Enable ATM UPC Function. |
| 1.3.6.1.4.1.277.1.5.1.1.83 | lportAtmUniType | 0 | 0 | The type of UNI for this ATM lport. |
| 1.3.6.1.4.1.277.1.5.1.1.84 | lportConnectionType | 0 | 0 | The type of connection at this lport. |
| 1.3.6.1.4.1.277.1.5.1.1.85 | lportAtmCellType | 0 | 0 | atm cell header with uni-format or nni-format with no GFC. |
| 1.3.6.1.4.1.277.1.5.1.1.86 | lportTrkKeepAliveTimer | 0 | 0 | Send a keep-alive packet after this many seconds. These packets are sent on trunk links only. The range is 0 thru 15, with zer… |
| 1.3.6.1.4.1.277.1.5.1.1.87 | lportTrkKeepAliveErrorThreshold | 0 | 0 | Declare the interface down after this many keep-alive packets in a row are missed. The default is five. |
| 1.3.6.1.4.1.277.1.5.1.1.88 | lportIgCutThruStatus | 0 | 0 | Enable ingress cut-thru on this user lport. Default is disabled. |
| 1.3.6.1.4.1.277.1.5.1.1.89 | lportEgCutThruStatus | 0 | 0 | Enable egress cut-thru on this user lport. Default is disabled. |
| 1.3.6.1.4.1.277.1.5.1.1.90 | lportEgCutThruThresh | 0 | 0 | Egress cut thru threshold - start transmitting a frame on a user port after this many segments have arrived. |
| 1.3.6.1.4.1.277.1.5.1.1.91 | lportFrameRelayTrkEnable | 0 | 0 | Allow Frame Relay Trunks on the user link. |
| 1.3.6.1.4.1.277.1.5.1.1.92 | lportSmdsSsiIf | 0 | 0 | The interface number of the SSI which this DXI/SNI is multiplexed to. |
| 1.3.6.1.4.1.277.1.5.1.1.93 | lportSmdsSsiSlot | 0 | 0 | The slot of the SSI which this DXI/SNI is multiplexed to. |
| 1.3.6.1.4.1.277.1.5.1.1.94 | lportSmdsScrnId | 0 | 0 | The ID of address screen for this interface. |
| 1.3.6.1.4.1.277.1.5.1.1.95 | lportSmdsIaScrnOp | 0 | 0 | Individual address screen operation. |
| 1.3.6.1.4.1.277.1.5.1.1.96 | lportSmdsGaScrnOp | 0 | 0 | Group address screen operation. |
| 1.3.6.1.4.1.277.1.5.1.1.97 | lportSmdsIaScrnMap | 0 | 0 | The individual address screen member bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. Th… |
| 1.3.6.1.4.1.277.1.5.1.1.98 | lportSmdsGaScrnMap | 0 | 0 | The group address screen member bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The fol… |
| 1.3.6.1.4.1.277.1.5.1.1.99 | lportSmdsTrkAddr | 0 | 0 | SMDS address. For SSI feeder port, this address is the local address of all SMDS optimum paths associated with this SSI feeder po… |
| 1.3.6.1.4.1.277.1.5.1.1.100 | lportSmdsCrc | 0 | 0 | CRC which CPE generates. |
| 1.3.6.1.4.1.277.1.5.1.1.101 | lportSmdsCpePoll | 0 | 0 | Whether CPE supports heart beat poll or not. |
| 1.3.6.1.4.1.277.1.5.1.1.102 | lportSmdsPduCheck | 0 | 0 | turn on/off the detailed SIP3 PDU error checking. |
| ... | ||||