This variable represents the desired loopback
configuration of the DS1 interface. Agents
supporting read/write access should return
inconsistentValue in response to a requested
loopback state that the interface does not
support. The values mean:
ds1NoLoop
Not in the loopback state. A device that is not
capable of performing a loopback on the interface
shall always return this as its value.
ds1PayloadLoop
The received signal at this interface is looped
through the device. Typically the received signal
is looped back for retransmission after it has
passed through the device's framing function.
ds1LineLoop
The received signal at this interface does not go
through the device (minimum penetration) but is
looped back out.
ds1OtherLoop
Loopbacks that are not defined here.
ds1InwardLoop
The transmitted signal at this interface is
looped back and received by the same interface.
What is transmitted onto the line is product
dependent.
ds1DualLoop
Both ds1LineLoop and ds1InwardLoop will be
active simultaneously.
Parsed from file lport_ds1.mib.txt
Company: None
Module: APPIAN-LPORT-DS1-MIB
This variable represents the desired loopback
configuration of the DS1 interface. Agents
supporting read/write access should return
inconsistentValue in response to a requested
loopback state that the interface does not
support. The values mean:
ds1NoLoop
Not in the loopback state. A device that is not
capable of performing a loopback on the interface
shall always return this as its value.
ds1PayloadLoop
The received signal at this interface is looped
through the device. Typically the received signal
is looped back for retransmission after it has
passed through the device's framing function.
ds1LineLoop
The received signal at this interface does not go
through the device (minimum penetration) but is
looped back out.
ds1OtherLoop
Loopbacks that are not defined here.
ds1InwardLoop
The transmitted signal at this interface is
looped back and received by the same interface.
What is transmitted onto the line is product
dependent.
ds1DualLoop
Both ds1LineLoop and ds1InwardLoop will be
active simultaneously.
Parsed from file APPIAN-LPORT-DS1-MIB.mib
Module: APPIAN-LPORT-DS1-MIB
Vendor: Tecnopro SA
Module: APPIAN-LPORT-DS1-MIB
[Automatically extracted from oidview.com]
acLogicalDs1ConfigLoopbackConfig OBJECT-TYPE SYNTAX INTEGER { ds1NoLoop(1), ds1PayloadLoop(2), ds1LineLoop(3), ds1OtherLoop(4), ds1InwardLoop(5), ds1DualLoop(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "This variable represents the desired loopback configuration of the DS1 interface. Agents supporting read/write access should return inconsistentValue in response to a requested loopback state that the interface does not support. The values mean: ds1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as its value. ds1PayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. ds1LineLoop The received signal at this interface does not go through the device (minimum penetration) but is looped back out. ds1OtherLoop Loopbacks that are not defined here. ds1InwardLoop The transmitted signal at this interface is looped back and received by the same interface. What is transmitted onto the line is product dependent. ds1DualLoop Both ds1LineLoop and ds1InwardLoop will be active simultaneously." DEFVAL { ds1NoLoop } ::= { acLogicalDs1ConfigEntry 14 }
acLogicalDs1ConfigLoopbackConfig OBJECT-TYPE SYNTAX INTEGER { ds1NoLoop(1), ds1PayloadLoop(2), ds1LineLoop(3), ds1OtherLoop(4), ds1InwardLoop(5), ds1DualLoop(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "This variable represents the desired loopback configuration of the DS1 interface. Agents supporting read/write access should return inconsistentValue in response to a requested loopback state that the interface does not support. The values mean: ds1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as its value. ds1PayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. ds1LineLoop The received signal at this interface does not go through the device (minimum penetration) but is looped back out. ds1OtherLoop Loopbacks that are not defined here. ds1InwardLoop The transmitted signal at this interface is looped back and received by the same interface. What is transmitted onto the line is product dependent. ds1DualLoop Both ds1LineLoop and ds1InwardLoop will be active simultaneously." DEFVAL { ds1NoLoop } ::= { acLogicalDs1ConfigEntry 14 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2785.2.4.2.1.1.1 | acLogicalDs1ConfigNodeId | 0 | 0 | The node id is the id for this specific node in the OSAP ring. |
| 1.3.6.1.4.1.2785.2.4.2.1.1.2 | acLogicalDs1ConfigIndex | 0 | 0 | This value for this object is equal to the value of index from the Time Slot Table that this DS1 corresponds. The value can be a… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.3 | acLogicalDs1ConfigAdminStatus | 0 | 0 | Appian Administrative Status attribute used to set the provisioning state as either activate(1), inactivate(2) or delete(3). Re… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.4 | acLogicalDs1ConfigTimeElapsedInterval | 0 | 0 | The number of seconds that have elapsed since the beginning of the near end current error- measurement period. If, for some reas… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.5 | acLogicalDs1ConfigValidIntervals | 0 | 0 | The number of previous near end intervals for which data was collected. The value will be 96 unless the interface was brought on… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.6 | acLogicalDs1ConfigTimeElapsedDay | 0 | 0 | The number of seconds that have elapsed since the beginning of the near end current day error- measurement period. If, for some … |
| 1.3.6.1.4.1.2785.2.4.2.1.1.7 | acLogicalDs1ConfigValidDays | 0 | 0 | The number of previous near end days for which data was collected. The value will be 30 unless the interface was brought online … |
| 1.3.6.1.4.1.2785.2.4.2.1.1.8 | acLogicalDs1ConfigTimeElapsedFarEndInterval | 0 | 0 | The number of seconds that have elapsed since the beginning of the far end current error-measurement period. If, for some reason… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.9 | acLogicalDs1ConfigValidFarEndIntervals | 0 | 0 | The number of previous near end intervals for which data was collected. The value will be 96 unless the interface was brought on… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.10 | acLogicalDs1ConfigTimeElapsedFarEndDay | 0 | 0 | The number of seconds that have elapsed since the beginning of the far end current day error- measurement period. If, for some r… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.11 | acLogicalDs1ConfigValidFarEndDays | 0 | 0 | The number of previous near end days for which data was collected. The value will be 30 unless the far/near end interface was br… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.12 | acLogicalDs1ConfigSendCode | 0 | 0 | This variable indicates what type of code is being sent across the DS1 interface by the device. Setting this variable causes the … |
| 1.3.6.1.4.1.2785.2.4.2.1.1.13 | acLogicalDs1ConfigCircuitIdentifier | 0 | 0 | This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. |
| 1.3.6.1.4.1.2785.2.4.2.1.1.15 | acLogicalDs1ConfigLineStatus | 0 | 0 | This variable indicates the Line Status of the interface. It contains loopback, failure, received 'alarm' and transmitted 'alarm… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.16 | acLogicalDs1ConfigTransmitClockSource | 0 | 0 | The source of Transmit Clock. For the logicalDs1, the timing will be throughTiming. This is not currently a configurable paramet… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.17 | acLogicalDs1ConfigInvalidIntervals | 0 | 0 | The number of intervals in the range from 0 to ds1ValidIntervals for which no data is available. This object will typically be z… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.18 | acLogicalDs1ConfigInvalidDays | 0 | 0 | The number of days in the range from 0 to ds1ValidDays for which no data is available. This object will typically be zero except … |
| 1.3.6.1.4.1.2785.2.4.2.1.1.19 | acLogicalDs1ConfigInvalidFarEndIntervals | 0 | 0 | The number of intervals in the range from 0 to acLogicalDs1ConfigValidFarEndIntervals for which no data is available. This objec… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.20 | acLogicalDs1ConfigInvalidFarEndDays | 0 | 0 | The number of days in the range from 0 to acLogicalDs1ConfigValidFarEndDays for which no data is available. This object will typ… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.21 | acLogicalDs1ConfigLineStatusLastChange | 0 | 0 | The value of MIB II's sysUpTime object at the time this DS1 entered its current line status state. If the current state was ente… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.22 | acLogicalDs1ConfigLineStatusChangeTrapEnable | 0 | 0 | Indicates whether acLogicalDs1ConfigLineStatusChange traps should be generated for this interface. |
| 1.3.6.1.4.1.2785.2.4.2.1.1.23 | acLogicalDs1ConfigLoopbackStatus | 0 | 0 | This variable represents the current state of the loopback on the DS1 interface. It contains information about loopbacks establi… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.24 | acLogicalDs1ConfigVTNumber | 0 | 0 | This variable represents the virtual tributary number in the STS-1 frame that this DS1 corresponds to. |