This variable indicates the Line Status of the
interface. It contains loopback, failure,
received 'alarm' and transmitted 'alarms
information.
The ds1LineStatus is a bit map represented as a
sum, therefore, it can represent multiple failures
(alarms) and a LoopbackState simultaneously.
ds1NoAlarm must be set if and only if no other
flag is set.
If the ds1loopbackState bit is set, the loopback
in effect can be determined from the
ds1loopbackConfig object.
The various bit positions are:
1 ds1NoAlarm No alarm present
2 ds1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm)
4 ds1XmtFarEndLOF Near end sending LOF Indication
8 ds1RcvAIS Far end sending AIS
16 ds1XmtAIS Near end sending AIS
32 ds1LossOfFrame Near end LOF (a.k.a., Red Alarm)
64 dsLossOfSignal Near end Loss Of Signal
128 ds1LoopbackState Near end is looped
256 ds1RcvFarEndLOMF Far End Sending TS16 LOMF
512 ds1XmtFarEndLOMF Near End Sending TS16 LOMF
1024 ds1RcvTestCode Near End detects a test code
2048 ds1OtherFailure any line status not defined here
4096 ds1UnavailSigState Near End in Unavailable Signal
State
16384 ds1NetEquipOOS Carrier Equipment Out of Service
Parsed from file lport_ds1.mib.txt
Company: None
Module: APPIAN-LPORT-DS1-MIB
This variable indicates the Line Status of the
interface. It contains loopback, failure,
received 'alarm' and transmitted 'alarms
information.
The ds1LineStatus is a bit map represented as a
sum, therefore, it can represent multiple failures
(alarms) and a LoopbackState simultaneously.
ds1NoAlarm must be set if and only if no other
flag is set.
If the ds1loopbackState bit is set, the loopback
in effect can be determined from the
ds1loopbackConfig object.
The various bit positions are:
1 ds1NoAlarm No alarm present
2 ds1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm)
4 ds1XmtFarEndLOF Near end sending LOF Indication
8 ds1RcvAIS Far end sending AIS
16 ds1XmtAIS Near end sending AIS
32 ds1LossOfFrame Near end LOF (a.k.a., Red Alarm)
64 dsLossOfSignal Near end Loss Of Signal
128 ds1LoopbackState Near end is looped
256 ds1RcvFarEndLOMF Far End Sending TS16 LOMF
512 ds1XmtFarEndLOMF Near End Sending TS16 LOMF
1024 ds1RcvTestCode Near End detects a test code
2048 ds1OtherFailure any line status not defined here
4096 ds1UnavailSigState Near End in Unavailable Signal
State
16384 ds1NetEquipOOS Carrier Equipment Out of Service
Parsed from file APPIAN-LPORT-DS1-MIB.mib
Module: APPIAN-LPORT-DS1-MIB
Vendor: Tecnopro SA
Module: APPIAN-LPORT-DS1-MIB
[Automatically extracted from oidview.com]
acLogicalDs1ConfigLineStatus OBJECT-TYPE SYNTAX INTEGER (1..131071) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the Line Status of the interface. It contains loopback, failure, received 'alarm' and transmitted 'alarms information. The ds1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. ds1NoAlarm must be set if and only if no other flag is set. If the ds1loopbackState bit is set, the loopback in effect can be determined from the ds1loopbackConfig object. The various bit positions are: 1 ds1NoAlarm No alarm present 2 ds1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm) 4 ds1XmtFarEndLOF Near end sending LOF Indication 8 ds1RcvAIS Far end sending AIS 16 ds1XmtAIS Near end sending AIS 32 ds1LossOfFrame Near end LOF (a.k.a., Red Alarm) 64 dsLossOfSignal Near end Loss Of Signal 128 ds1LoopbackState Near end is looped 256 ds1RcvFarEndLOMF Far End Sending TS16 LOMF 512 ds1XmtFarEndLOMF Near End Sending TS16 LOMF 1024 ds1RcvTestCode Near End detects a test code 2048 ds1OtherFailure any line status not defined here 4096 ds1UnavailSigState Near End in Unavailable Signal State 16384 ds1NetEquipOOS Carrier Equipment Out of Service" ::= { acLogicalDs1ConfigEntry 15 }
acLogicalDs1ConfigLineStatus OBJECT-TYPE SYNTAX INTEGER (1..131071) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the Line Status of the interface. It contains loopback, failure, received 'alarm' and transmitted 'alarms information. The ds1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. ds1NoAlarm must be set if and only if no other flag is set. If the ds1loopbackState bit is set, the loopback in effect can be determined from the ds1loopbackConfig object. The various bit positions are: 1 ds1NoAlarm No alarm present 2 ds1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm) 4 ds1XmtFarEndLOF Near end sending LOF Indication 8 ds1RcvAIS Far end sending AIS 16 ds1XmtAIS Near end sending AIS 32 ds1LossOfFrame Near end LOF (a.k.a., Red Alarm) 64 dsLossOfSignal Near end Loss Of Signal 128 ds1LoopbackState Near end is looped 256 ds1RcvFarEndLOMF Far End Sending TS16 LOMF 512 ds1XmtFarEndLOMF Near End Sending TS16 LOMF 1024 ds1RcvTestCode Near End detects a test code 2048 ds1OtherFailure any line status not defined here 4096 ds1UnavailSigState Near End in Unavailable Signal State 16384 ds1NetEquipOOS Carrier Equipment Out of Service" ::= { acLogicalDs1ConfigEntry 15 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2785.2.4.2.1.1.1 | acLogicalDs1ConfigNodeId | 0 | 0 | The node id is the id for this specific node in the OSAP ring. |
| 1.3.6.1.4.1.2785.2.4.2.1.1.2 | acLogicalDs1ConfigIndex | 0 | 0 | This value for this object is equal to the value of index from the Time Slot Table that this DS1 corresponds. The value can be a… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.3 | acLogicalDs1ConfigAdminStatus | 0 | 0 | Appian Administrative Status attribute used to set the provisioning state as either activate(1), inactivate(2) or delete(3). Re… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.4 | acLogicalDs1ConfigTimeElapsedInterval | 0 | 0 | The number of seconds that have elapsed since the beginning of the near end current error- measurement period. If, for some reas… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.5 | acLogicalDs1ConfigValidIntervals | 0 | 0 | The number of previous near end intervals for which data was collected. The value will be 96 unless the interface was brought on… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.6 | acLogicalDs1ConfigTimeElapsedDay | 0 | 0 | The number of seconds that have elapsed since the beginning of the near end current day error- measurement period. If, for some … |
| 1.3.6.1.4.1.2785.2.4.2.1.1.7 | acLogicalDs1ConfigValidDays | 0 | 0 | The number of previous near end days for which data was collected. The value will be 30 unless the interface was brought online … |
| 1.3.6.1.4.1.2785.2.4.2.1.1.8 | acLogicalDs1ConfigTimeElapsedFarEndInterval | 0 | 0 | The number of seconds that have elapsed since the beginning of the far end current error-measurement period. If, for some reason… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.9 | acLogicalDs1ConfigValidFarEndIntervals | 0 | 0 | The number of previous near end intervals for which data was collected. The value will be 96 unless the interface was brought on… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.10 | acLogicalDs1ConfigTimeElapsedFarEndDay | 0 | 0 | The number of seconds that have elapsed since the beginning of the far end current day error- measurement period. If, for some r… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.11 | acLogicalDs1ConfigValidFarEndDays | 0 | 0 | The number of previous near end days for which data was collected. The value will be 30 unless the far/near end interface was br… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.12 | acLogicalDs1ConfigSendCode | 0 | 0 | This variable indicates what type of code is being sent across the DS1 interface by the device. Setting this variable causes the … |
| 1.3.6.1.4.1.2785.2.4.2.1.1.13 | acLogicalDs1ConfigCircuitIdentifier | 0 | 0 | This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. |
| 1.3.6.1.4.1.2785.2.4.2.1.1.14 | acLogicalDs1ConfigLoopbackConfig | 0 | 0 | This variable represents the desired loopback configuration of the DS1 interface. Agents supporting read/write access should ret… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.16 | acLogicalDs1ConfigTransmitClockSource | 0 | 0 | The source of Transmit Clock. For the logicalDs1, the timing will be throughTiming. This is not currently a configurable paramet… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.17 | acLogicalDs1ConfigInvalidIntervals | 0 | 0 | The number of intervals in the range from 0 to ds1ValidIntervals for which no data is available. This object will typically be z… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.18 | acLogicalDs1ConfigInvalidDays | 0 | 0 | The number of days in the range from 0 to ds1ValidDays for which no data is available. This object will typically be zero except … |
| 1.3.6.1.4.1.2785.2.4.2.1.1.19 | acLogicalDs1ConfigInvalidFarEndIntervals | 0 | 0 | The number of intervals in the range from 0 to acLogicalDs1ConfigValidFarEndIntervals for which no data is available. This objec… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.20 | acLogicalDs1ConfigInvalidFarEndDays | 0 | 0 | The number of days in the range from 0 to acLogicalDs1ConfigValidFarEndDays for which no data is available. This object will typ… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.21 | acLogicalDs1ConfigLineStatusLastChange | 0 | 0 | The value of MIB II's sysUpTime object at the time this DS1 entered its current line status state. If the current state was ente… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.22 | acLogicalDs1ConfigLineStatusChangeTrapEnable | 0 | 0 | Indicates whether acLogicalDs1ConfigLineStatusChange traps should be generated for this interface. |
| 1.3.6.1.4.1.2785.2.4.2.1.1.23 | acLogicalDs1ConfigLoopbackStatus | 0 | 0 | This variable represents the current state of the loopback on the DS1 interface. It contains information about loopbacks establi… |
| 1.3.6.1.4.1.2785.2.4.2.1.1.24 | acLogicalDs1ConfigVTNumber | 0 | 0 | This variable represents the virtual tributary number in the STS-1 frame that this DS1 corresponds to. |