This trap indicates that the Alarm Indication Signal (AIS)
is detected on the incoming virtual channel. This trap
is generated once when the virtual channel is declared
to be in the active AIS state.
Parsed from file fore-oam.mib.txt
Company: marconi
Module: Fore-OAM-MIB
asxVCOAMAISDetected NOTIFICATION-TYPE OBJECTS { portName, chanPort, chanVPI, chanVCI, oamConnFlow } STATUS current DESCRIPTION "This trap indicates that the Alarm Indication Signal (AIS) is detected on the incoming virtual channel. This trap is generated once when the virtual channel is declared to be in the active AIS state." ::= { atmSwitch 0 2054 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.326.2.2.0.2004 | pnniSpvccDown | 0 | 0 | This trap is sent when a SPVC call is cleared or deleted. The pnniSpvcSrcDownReason indicates if the call was cleared due to a be… |
| 1.3.6.1.4.1.326.2.2.0.2005 | pnniSpvccUp | 0 | 0 | This trap is send when a SPVC call is established. It identifies the SPVC and the old and new cost. If the call has not been up b… |
| 1.3.6.1.4.1.326.2.2.0.2006 | pnniSpvccFail | 0 | 0 | This trap is sent when a SPVC call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnni… |
| 1.3.6.1.4.1.326.2.2.0.2007 | pnniSpvpcDown | 0 | 0 | This trap is sent when a SPVP call is cleared. The pnniSpvcSrcDownReason indicates if the call was cleared due to a better route … |
| 1.3.6.1.4.1.326.2.2.0.2008 | pnniSpvpcUp | 0 | 0 | This trap is send when a SPVP call is established. It identifies the SPVP and the old and new cost. If the call has not been up b… |
| 1.3.6.1.4.1.326.2.2.0.2009 | pnniSpvpcFail | 0 | 0 | This trap is sent when a SPVP call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnni… |
| 1.3.6.1.4.1.326.2.2.0.2010 | asxPortCardDown | 0 | 0 | An asxPortCardDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch portcards, that … |
| 1.3.6.1.4.1.326.2.2.0.2011 | asxPortCardUp | 0 | 0 | An asxPortCardUp trap signifies that the sending protocol entity recognizes a new operational ATM Switch port card, that is ident… |
| 1.3.6.1.4.1.326.2.2.0.2013 | asxServiceCategoryOutputQueueCongested | 0 | 0 | This trap indicates that the output queue for the service category has exceeded its dedicated length, and has begun overflowing i… |
| 1.3.6.1.4.1.326.2.2.0.2014 | asxServiceCategoryOutputQueueCellLoss | 0 | 0 | This trap indicates that the output queue for the given service category has overflowed and cells have been dropped. |
| 1.3.6.1.4.1.326.2.2.0.2015 | pnniNormalToOverloadTransition | 0 | 0 | This trap is generated on transition from the normal state to the overload state. |
| 1.3.6.1.4.1.326.2.2.0.2016 | pnniOverloadToNormalTransition | 0 | 0 | This trap is generated on transition from the overload to the normal state. |
| 1.3.6.1.4.1.326.2.2.0.2017 | apsSwitchOver | 0 | 0 | This trap alerts that an aps switchover has occurred and the active port is identified by the tuple {hwPortBoard, hwPortModule, h… |
| 1.3.6.1.4.1.326.2.2.0.2018 | redundancyFabricSwitchover | 0 | 0 | This trap reports the change of active fabric due to an automatic or revertive switchover. The fabric identified by the trap vari… |
| 1.3.6.1.4.1.326.2.2.0.2019 | apsModeMismatchDeclare | 0 | 0 | This trap alerts that an aps mode mismatch has occurred on aps group. |
| 1.3.6.1.4.1.326.2.2.0.2020 | pnniPmpRerouteInitiated | 0 | 0 | This trap is sent when a party is being re-routed due to a better path being found or if a reroute is requested using a AMI comm… |
| 1.3.6.1.4.1.326.2.2.0.2021 | pnniPmpSpvcUp | 0 | 0 | This trap is send when a pmp SPVC call is established. This trap is only sent if pnniSpvcTrapMode is failure or all. |
| 1.3.6.1.4.1.326.2.2.0.2022 | pnniPmpSpvcDown | 0 | 0 | This trap is sent when a pmp SPVC call is cleared. The pnniSpvcSrcDownReason indicates if the call was cleared due to a better ro… |
| 1.3.6.1.4.1.326.2.2.0.2023 | pnniPmpSpvcFail | 0 | 0 | This trap is sent when a SPVC call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnni… |
| 1.3.6.1.4.1.326.2.2.0.2024 | pnniSpvxRGroupSwover | 0 | 0 | This trap is sent when a automatic switch over occurs in a SPVC Redundancy group that has automatic PVC switch over enabled. |
| 1.3.6.1.4.1.326.2.2.0.2025 | asxSVXCPStateTransferFailed | 0 | 0 | This trap is sent when the SVx/SPVx Preservation module is unable to transfer call and interface state information to the Standby… |
| 1.3.6.1.4.1.326.2.2.0.2026 | asxSVXCPStateTransferRestarted | 0 | 0 | This trap is sent when the SVx/SPVx Preservation module has restarted its transfer of call and interface state information to the… |
| 1.3.6.1.4.1.326.2.2.0.2027 | asxSVXCPStateDroppedCall | 0 | 0 | This trap is sent when the SVx/SPVx Preservation module has insufficient memory to store one or more calls during its transfer of… |
| 1.3.6.1.4.1.326.2.2.0.2028 | apsModeMismatchClear | 0 | 0 | This trap alerts that an aps mode mismatch has cleared on aps group. |
| 1.3.6.1.4.1.326.2.2.0.2040 | elecredSwitchOver | 0 | 0 | This trap alerts that an electrical redundancy switchover has occurred and the active port is identified by the tuple {hwPortBoa… |
| 1.3.6.1.4.1.326.2.2.0.2050 | asxVPOAMAISDetected | 0 | 0 | This trap indicates that the Alarm Indication Signal (AIS) is detected on the incoming (terminating) virtual path. This trap is … |
| 1.3.6.1.4.1.326.2.2.0.2051 | asxVPOAMAISCleared | 0 | 0 | This trap indicates that the Alarm Indication Signal (AIS) has been removed from the incoming (terminating) virtual path. This tr… |
| 1.3.6.1.4.1.326.2.2.0.2052 | asxVPOAMRDIDetected | 0 | 0 | This trap indicates that the Remote Defect Indication (RDI) is detected on the incoming (terminating) virtual path. This trap is… |
| 1.3.6.1.4.1.326.2.2.0.2053 | asxVPOAMRDICleared | 0 | 0 | This trap indicates that the Remote Defect Indication (RDI) has been removed from the incoming (terminating) virtual path. This t… |
| 1.3.6.1.4.1.326.2.2.0.2055 | asxVCOAMAISCleared | 0 | 0 | This trap indicates that the Alarm Indication Signal (AIS) has been removed from the incoming virtual channel. This trap is gene… |
| 1.3.6.1.4.1.326.2.2.0.2056 | asxVCOAMRDIDetected | 0 | 0 | This trap indicates that the Remote Defect Indication (RDI) is detected on the incoming virtual channel. This trap is generated … |
| 1.3.6.1.4.1.326.2.2.0.2057 | asxVCOAMRDICleared | 0 | 0 | This trap indicates that the Remote Defect Indication (RDI) has been removed from the incoming virtual channel. This trap is gen… |
| 1.3.6.1.4.1.326.2.2.0.2058 | asxVCOAMCLR0HitThreshold | 0 | 0 | The F5 CP sends this trap when the CLR0 threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2059 | asxVCOAMCLR1HitThreshold | 0 | 0 | The F5 CP sends this trap when the CLR1 threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2060 | asxVCOAMCLR01HitThreshold | 0 | 0 | The F5 CP sends this trap when the CLR0+1 threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2061 | asxVCOAMRogueCellHitThreshold | 0 | 0 | The F5 CP sends this trap when the rogue cells count threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2062 | asxVCOAMErroredCellHitThreshold | 0 | 0 | The F5 CP sends this trap when the errored cells count threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2063 | asxVCOAMBip16Threshold | 0 | 0 | The F5 CP sends this trap when even parity is detected in Block Error Detection Code BIP-16. Ref: ITU I.610 paragraph 10.3.1 Item… |
| 1.3.6.1.4.1.326.2.2.0.2064 | asxVPOAMCLR0HitThreshold | 0 | 0 | The F4 CP sends this trap when the CLR0 threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2065 | asxVPOAMCLR1HitThreshold | 0 | 0 | The F4 CP sends this trap when the CLR1 threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2066 | asxVPOAMCLR01HitThreshold | 0 | 0 | The F4 CP sends this trap when the CLR0+1 threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2067 | asxVPOAMRogueCellHitThreshold | 0 | 0 | The F4 CP sends this trap when the rogue cells count threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2068 | asxVPOAMErroredCellHitThreshold | 0 | 0 | The F4 CP sends this trap when the errored cells count threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2069 | asxVPOAMBip16Threshold | 0 | 0 | The F4 CP sends a VP trap when even parity is detected in Block Error Detection Code BIP-16. Ref: ITU I.610 paragraph 10.3.1 Item… |
| 1.3.6.1.4.1.326.2.2.0.2070 | asxVCOAMSecbrHitThreshold | 0 | 0 | The F5 CP sends this trap when the SECBR threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2071 | asxVPOAMSecbrHitThreshold | 0 | 0 | The F4 CP sends this trap when the SECBR threshold is hit. |
| 1.3.6.1.4.1.326.2.2.0.2072 | asxVCOAMActivated | 0 | 0 | This trap indicates that a F5 CP has been activated. It also reports the status of the activation. |
| 1.3.6.1.4.1.326.2.2.0.2073 | asxVCOAMDeactivated | 0 | 0 | This trap indicates that a F5 CP has been deactivated. It also reports the status of the deactivation. |
| 1.3.6.1.4.1.326.2.2.0.2074 | asxVPOAMActivated | 0 | 0 | This trap indicates that a F4 CP has been activated. It also reports the status of the activation. |
| 1.3.6.1.4.1.326.2.2.0.2075 | asxVPOAMDeactivated | 0 | 0 | This trap indicates that a F4 CP has been deactivated. It also reports the status of the deactivation. |
| 1.3.6.1.4.1.326.2.2.0.2076 | asxVCOAMCriticalMcsnJump | 0 | 0 | The F5 CP sends this trap when there is a critical jump in MCSN received from the peer CP. This indicates a lost in some of the … |
| 1.3.6.1.4.1.326.2.2.0.2077 | asxVPOAMCriticalMcsnJump | 0 | 0 | The F4 CP sends this trap when there is a critical jump in MCSN received from the peer CP. This indicates a lost in some of the … |
| ... | ||||