This attribute shall specify the set of data rates
at which the station may transmit data. Each octet
contains a value representing a rate. Each rate
shall be within the range from 2 to 127,
corresponding to data rates in increments of
500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be
supported (as indicated in the supported rates
table) for receiving data. This value is reported in
transmitted Beacon, Probe Request, Probe Response,
Association Request, Association Response,
Reassociation Request, and Reassociation Response
frames, and is used to determine whether a BSS
with which the station desires to synchronize is
suitable. It is also used when starting a BSS,
as specified in 10.3.
Parsed from file RoamAbout-MIB.mib
Module: RoamAbout-MIB
Vendor: DEC
Module: RoamAbout-MIB
[Automatically extracted from oidview.com]
rabtDot11CurrentOperationalRate OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..126)) ACCESS read-only STATUS mandatory DESCRIPTION "This attribute shall specify the set of data rates at which the station may transmit data. Each octet contains a value representing a rate. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be supported (as indicated in the supported rates table) for receiving data. This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames, and is used to determine whether a BSS with which the station desires to synchronize is suitable. It is also used when starting a BSS, as specified in 10.3." ::= { rabtDot11Current 4 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.36.2.18.35.15.1.1 | rabtDot11CurrentChannel | 0 | 0 | The CURRENT channel. |
| 1.3.6.1.4.1.36.2.18.35.15.1.2 | rabtDot11CurrentNetworkName | 0 | 0 | The CURRENT network name. |
| 1.3.6.1.4.1.36.2.18.35.15.1.3 | rabtDot11CurrentStationName | 0 | 0 | Defines the CURRENT station name of the radio interface, used by client utilities. |
| 1.3.6.1.4.1.36.2.18.35.15.1.5 | rabtDot11CurrentSystemScale | 0 | 0 | Specifies the CURRENT Access Point density in the ESS. |
| 1.3.6.1.4.1.36.2.18.35.15.1.6 | rabtDot11CurrentDTIMPeriod | 0 | 0 | Defines the CURRENT number of beacon intervals between successive DTIMs. |
| 1.3.6.1.4.1.36.2.18.35.15.1.7 | rabtDot11CurrentFragmentationThreshold | 0 | 0 | This attribute shall specify the mandatory maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall b… |
| 1.3.6.1.4.1.36.2.18.35.15.1.8 | rabtDot11CurrentRTSThreshold | 0 | 0 | This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CT… |
| 1.3.6.1.4.1.36.2.18.35.15.1.9 | rabtDot11CurrentMulticastPMBuffering | 0 | 0 | Defines if multicast MAC frames are CURRENTLY buffered for transmission after DTIM. If disabled, MAC frames are immediately plac… |
| 1.3.6.1.4.1.36.2.18.35.15.1.10 | rabtDot11CurrentSecureAccess | 0 | 0 | When this mode is set to enabled, the AP will only associate with stations that have the same network name as the AP. When this m… |
| 1.3.6.1.4.1.36.2.18.35.15.1.11 | rabtDot11CurrentTransmitRate | 0 | 0 | This value specifies the transmission rate of the AP. It is implemented when cards that operate faster than the 2Mbit 802.11 stan… |
| 1.3.6.1.4.1.36.2.18.35.15.1.12 | rabtDot11CurrentPrivacyInvoked | 0 | 0 | When this attribute is true, it shall indicate that the AP is currently using the 802.11 WEP mechanism for transmitting frames of… |
| 1.3.6.1.4.1.36.2.18.35.15.1.13 | rabtDot11CurrentExcludeUnencrypted | 0 | 0 | This value indicates the current setting of the dot11ExcludeUnencrypted attribute in the AP. |