s3TrNmmOldTestPathtable
View at oid-info.com
Table used to initiate a path test between two
MAC addresses. To initiate a test the object
s3TrNmmOldTpStatus should be supplied with
start-test(2). If s3TrNmmOldTpRoute is not
supplied in the PDU then the test will check to
see if any path to between the stations exists.
If a route is supplied, then only the specified
route between the two stations will be checked.
Supplying a route on a set requires an ATOMIC SET
OPERATION.
After a test is completed it may live in the
table for some period of time. This time is not
specified by the MIB but is implementation
dependent (currently 2 minutes). There can only
be one test between a given source and
destination active in the table at any time (this
also means that only one test between a source
and destination can be active at any time).
For additional implementation details, see
Appendix A of this document.
Parsed from file s3tok430.mib.txt
Company: nortel
Module: SYNOPTICS-TOKENRING-MIB
Vendor: Nortel Networks
Module: SYNOPTICS-TOKENRING-MIB (s3tok430.mib)
Type: TABLE
Access: not-accessible
Syntax: SEQUENCE OF
Automatically extracted from www.mibdepot.com
s3TrNmmOldTestPathTable OBJECT-TYPE SYNTAX SEQUENCE OF S3TrNmmOldTestPathEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "Table used to initiate a path test between two MAC addresses. To initiate a test the object s3TrNmmOldTpStatus should be supplied with start-test(2). If s3TrNmmOldTpRoute is not supplied in the PDU then the test will check to see if any path to between the stations exists. If a route is supplied, then only the specified route between the two stations will be checked. Supplying a route on a set requires an ATOMIC SET OPERATION. After a test is completed it may live in the table for some period of time. This time is not specified by the MIB but is implementation dependent (currently 2 minutes). There can only be one test between a given source and destination active in the table at any time (this also means that only one test between a source and destination can be active at any time). For additional implementation details, see Appendix A of this document." ::= { s3000TrNmm 13 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.45.1.3.3.4.13.1 | s3TrNmmOldTestPathEntry | 4 | 4 | Entry of running tests and completed tests. |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.45.1.3.3.4.1 | s3TrNmmFnNum | 1 | 1 | Defines the flat network number that this NMM is part of. |
| 1.3.6.1.4.1.45.1.3.3.4.2 | s3TrNmmRingNum | 1 | 1 | Defines the segment number that this NMM is connected to. |
| 1.3.6.1.4.1.45.1.3.3.4.3 | s3TrNmmSlotNum | 1 | 1 | Defines the slot number that this NMM is connected to. New NMS implementations should use the object s3AgentMySlotId defined in … |
| 1.3.6.1.4.1.45.1.3.3.4.4 | s3TrNmmFpuIdRev | 1 | 1 | The revision of the Front-end Frame Processing unit. 0=Rev. A, 1=Rev. B, etc. |
| 1.3.6.1.4.1.45.1.3.3.4.5 | s3TrNmmFpuStatus | 1 | 1 | The status of the Front-end Frame Processing Unit. |
| 1.3.6.1.4.1.45.1.3.3.4.6 | s3TrNmmDramSize | 1 | 1 | The highest address of the DRAM in the NMM memory map. The possible values are: other(1).........Unknown size k512(2)..........512… |
| 1.3.6.1.4.1.45.1.3.3.4.7 | s3TrNmmEepromSize | 1 | 1 | The size of the EEPROM in the NMM memory map. The possible values are: other(1)..........Unknown size size2kBytes(4)....2K by 8 siz… |
| 1.3.6.1.4.1.45.1.3.3.4.8 | s3TrNmmGrpAddrFrmsRxOk | 1 | 1 | Number of Group Address frames received without error by this NMM. Note: The NMM counts only Group Address frames that are addres… |
| 1.3.6.1.4.1.45.1.3.3.4.9 | s3TrNmmRing1or2 | 1 | 1 | Determines which ring the NMM is currently using on the concentrator backplane. |
| 1.3.6.1.4.1.45.1.3.3.4.10 | s3TrNmmRingSpeed | 1 | 1 | Token Ring speed. |
| 1.3.6.1.4.1.45.1.3.3.4.11 | s3TrNmmHexDisplay | 1 | 1 | 4 octet hex display string that is displayed on the NMM control panel. |
| 1.3.6.1.4.1.45.1.3.3.4.12 | s3TrNmmEpromSize | 1 | 1 | The size of the EPROM in the NMM memory map. |
| 1.3.6.1.4.1.45.1.3.3.4.14 | s3TrNmmAuthStatus | 1 | 1 | Turning this object on(2) means that any node that is heard on this ring which is not currently in the s3TrAuthNodesTable will ca… |
| 1.3.6.1.4.1.45.1.3.3.4.15 | s3TrNmmAuthAction | 1 | 1 | If s3TrNmmAuthStatus is on(2) and the condition described by that object happens, then the action specified by this object will t… |
| 1.3.6.1.4.1.45.1.3.3.4.16 | s3TrNmmTestPathTestTimer | 1 | 1 | s3TrNmmTestPathtestTimer |
| 1.3.6.1.4.1.45.1.3.3.4.17 | s3TrNmmTestPathAgeTimer | 1 | 1 | The amount of time in unit of 100 milliseconds that an entry remains in table s3TrNmmTestPathTable before it is automatically rem… |
| 1.3.6.1.4.1.45.1.3.3.4.18 | s3TrNmmTestPathTable | 1 | 7 | s3TrNmmTestPathtable |
| 1.3.6.1.4.1.45.1.3.3.4.19 | s3TrNmmBnRiRoUnWrapIntval | 1 | 1 | The time in seconds an NMM will wait before it checks the beaconing condition on a Ring In Ring Out port. |
| 1.3.6.1.4.1.45.1.3.3.4.20 | s3TrNmmBnWrapTimerThreshd | 1 | 1 | The time in seconds a station is allowed to beacon before it is permanently wrapped by the NMM. |
| 1.3.6.1.4.1.45.1.3.3.4.21 | s3TrNmmBnWrapRetryThreshd | 1 | 1 | The number of times a port is allowed to beacon before it is permanently wrapped by the NMM. |
| 1.3.6.1.4.1.45.1.3.3.4.22 | s3TrNmmBnRmvalCondition | 1 | 1 | The use of the auto beacon removal process. A value of off(3) disables the process, and a value of on(2) enables it. Normally, th… |
| 1.3.6.1.4.1.45.1.3.3.4.23 | s3TrNmmBnWrapTrapIntval | 1 | 1 | The time interval in seconds in between the consecutive auto beacon wrap traps. |