To initiate a test, write to this object with the
appropriate value. If a test between this station
and the NMM has already been started or if a test
between this station and the NMM has completed but
has not aged out of the table the NMM's response
will return 'no error' to the SNMP Set request.
However, the NMM will not initiate a new test.
If the test cannot be started because of errors
in the SET request or if the test path operation
could not be started because of some limitations
on the agent side (e.g., the table limit has been
exceeded) then the response of a SET operation will
be SNMP 'bad value' or 'general' error. After the
SET has completed successfully, a GET of this object
will return the value that was previously SET. To
check the test status, GET the value of
s3TrNmmTpStatus. It has current status of the test.
To clear a test (i.e., removed the entry from the
table), use a SET with value 'clearTest'.
When a test is started, the NMM will issue a LLC test
frame request to the destination station. For both
start-test and retry-test the time-out value for the
entry will be set to the starting value (i.e., as if
the test was just started).
Parsed from file s3tok430.mib.txt
Company: nortel
Module: SYNOPTICS-TOKENRING-MIB
Vendor: Nortel Networks
Module: SYNOPTICS-TOKENRING-MIB (s3tok430.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
s3TrNmmTpStart OBJECT-TYPE SYNTAX INTEGER { other(1), startTestSourceRoute(2), startTestTransparent(3), retryTestSourceRoute(4), retryTestTransparent(5), clearTest(6) } ACCESS read-write STATUS mandatory DESCRIPTION "To initiate a test, write to this object with the appropriate value. If a test between this station and the NMM has already been started or if a test between this station and the NMM has completed but has not aged out of the table the NMM's response will return 'no error' to the SNMP Set request. However, the NMM will not initiate a new test. If the test cannot be started because of errors in the SET request or if the test path operation could not be started because of some limitations on the agent side (e.g., the table limit has been exceeded) then the response of a SET operation will be SNMP 'bad value' or 'general' error. After the SET has completed successfully, a GET of this object will return the value that was previously SET. To check the test status, GET the value of s3TrNmmTpStatus. It has current status of the test. To clear a test (i.e., removed the entry from the table), use a SET with value 'clearTest'. When a test is started, the NMM will issue a LLC test frame request to the destination station. For both start-test and retry-test the time-out value for the entry will be set to the starting value (i.e., as if the test was just started)." DEFVAL { startTestSourceRoute } ::={s3TrNmmTestPathEntry 2}
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.45.1.3.3.4.18.1.1 | s3TrNmmTpAddrTo | 0 | 0 | The destination MAC address to be used for the testpath operation |
| 1.3.6.1.4.1.45.1.3.3.4.18.1.3 | s3TrNmmTpStatus | 0 | 0 | The current status of the test. If the interval of time between the NMM's request and the station's response is less than s3TrNm… |
| 1.3.6.1.4.1.45.1.3.3.4.18.1.4 | s3TrNmmTpRoute | 0 | 0 | The encoded octet string that specifies the source route path of a successful startTestSourceRoute. The first octet represents th… |
| 1.3.6.1.4.1.45.1.3.3.4.18.1.5 | s3TrNmmTpDuration | 0 | 0 | This specifies the round trip time of a successful test in units of 100 milliseconds. This object will be equal to the value of s… |
| 1.3.6.1.4.1.45.1.3.3.4.18.1.6 | s3TrNmmTpTimeStamp | 0 | 0 | This is the time stamp (i.e., sysUpTime) of the last time that the path test was run successfully. |