Indicates whether the trunk is connected to a
segment that will perform beacon recovery. This
should be set to exists(1) for trunks which connect
to hubs which perform beacon recovery. This attribute
is used to determine the fault domain when resolving a
beaconing condition.
The beacon recovery process will resolve beaconing on
trunks with this attribute set to nonExists(2) before
trunks with the attribute set to exists(1) are resolved.
For backplane trunks, setting to a value other than
notApplicable will return invalidData error. The
default value is nonExists(2).
Parsed from file isd_mib.txt
Company: a3com
Module: CHIPCOMMIB
Vendor: 3Com
Module: CHIPCOMMIB (isd_mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
ol52nnMCRTrunkExtBcnRecovery OBJECT-TYPE SYNTAX INTEGER { exists(1), nonExists(2), notApplicable(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which perform beacon recovery. This attribute is used to determine the fault domain when resolving a beaconing condition. The beacon recovery process will resolve beaconing on trunks with this attribute set to nonExists(2) before trunks with the attribute set to exists(1) are resolved. For backplane trunks, setting to a value other than notApplicable will return invalidData error. The default value is nonExists(2)." ::= { ol52nnMCRTrunkEntry 10 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.1 | ol52nnMCRTrunkSlotIndex | 0 | 0 | The slot number of this trunk's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.2 | ol52nnMCRTrunkIndex | 0 | 0 | The trunk number of this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.3 | ol52nnMCRTrunkDipAdminState | 0 | 0 | The state of this trunk as indicated by the trunk's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.4 | ol52nnMCRTrunkPhantomMode | 0 | 0 | If enabled(1), then the trunk will operate in Phantom Mode. Note that Cable Monitor and Phantom Modes are mutually exclusive. I… |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.5 | ol52nnMCRTrunkDipPhantomMode | 0 | 0 | The Phantom Mode as indicated by this module's dip switches. Refer to previous object's description. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.6 | ol52nnMCRTrunkCableMon | 0 | 0 | The cable monitor configuration for this trunk. Note that Cable Monitor and Phantom Modes are mutually exclusive. If one attribu… |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.7 | ol52nnMCRTrunkDipCableMon | 0 | 0 | The cable monitor configuration as indicated by this module's dipswitches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.8 | ol52nnMCRTrunkJumperCableImp | 0 | 0 | The setting of this trunk's impedance matching, with ohm100(1) corresponding to unshielded twisted pair cabling and ohm150(2) cor… |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.9 | ol52nnMCRTrunkNetMapState | 0 | 0 | The map state of the copper Ring In trunk. This should be set to external(3) for Ring In trunks which connect to external hubs. … |