The map state of the copper Ring In trunk. This
should be set to external(3) for Ring In trunks which
connect to external hubs. The mapping logic will not
operate on trunks which are set to external(3). This
prevents incorrect mapping which can occur when a
module in one hub detects the mapping signal from
another hub.
Parsed from file isd_mib.txt
Company: a3com
Module: CHIPCOMMIB
Vendor: 3Com
Module: CHIPCOMMIB (isd_mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
ol52nnMCRTrunkNetMapState OBJECT-TYPE SYNTAX INTEGER { notApplicable(1), internal(2), external(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The map state of the copper Ring In trunk. This should be set to external(3) for Ring In trunks which connect to external hubs. The mapping logic will not operate on trunks which are set to external(3). This prevents incorrect mapping which can occur when a module in one hub detects the mapping signal from another hub." ::= { ol52nnMCRTrunkEntry 9 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.1 | ol52nnMCRTrunkSlotIndex | 0 | 0 | The slot number of this trunk's module. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.2 | ol52nnMCRTrunkIndex | 0 | 0 | The trunk number of this trunk. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.3 | ol52nnMCRTrunkDipAdminState | 0 | 0 | The state of this trunk as indicated by the trunk's dip switches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.4 | ol52nnMCRTrunkPhantomMode | 0 | 0 | If enabled(1), then the trunk will operate in Phantom Mode. Note that Cable Monitor and Phantom Modes are mutually exclusive. I… |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.5 | ol52nnMCRTrunkDipPhantomMode | 0 | 0 | The Phantom Mode as indicated by this module's dip switches. Refer to previous object's description. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.6 | ol52nnMCRTrunkCableMon | 0 | 0 | The cable monitor configuration for this trunk. Note that Cable Monitor and Phantom Modes are mutually exclusive. If one attribu… |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.7 | ol52nnMCRTrunkDipCableMon | 0 | 0 | The cable monitor configuration as indicated by this module's dipswitches. |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.8 | ol52nnMCRTrunkJumperCableImp | 0 | 0 | The setting of this trunk's impedance matching, with ohm100(1) corresponding to unshielded twisted pair cabling and ohm150(2) cor… |
| 1.3.6.1.4.1.49.2.3.1.4.4.59.3.1.10 | ol52nnMCRTrunkExtBcnRecovery | 0 | 0 | Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for tru… |