snmp540DiagTest OBJECT IDENTIFIER ::= { snmp540 7 }
Vendor: General DataComm, Inc.
Module: SNMP540-MGMT-MIB
[Automatically extracted from oidview.com]
snmp540DiagTest OBJECT IDENTIFIER ::= { snmp540 7 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.498.8.4.7.1 | snmp540DiagTestPattern | 1 | 1 | The Self Test Pattern choices generated internally by the snmp540 are 511 Pattern (snmp540Send511Pattern(2)), 2047 pattern, (snmp5… |
| 1.3.6.1.4.1.498.8.4.7.2 | snmp540DiagTestExceptions | 1 | 1 | Indicates exceptions that have occurred that may affect interpretation of the test results. The exception values are: value excepti… |
| 1.3.6.1.4.1.498.8.4.7.3 | snmp540DiagBitErrors | 1 | 1 | The bit errors of the most recently run diagnostic test. If TestExceptions reports bitsOutOfRange, this object should be ignored. |
| 1.3.6.1.4.1.498.8.4.7.4 | snmp540DiagBlockErrors | 1 | 1 | The block errors of the most recently run diagnostic test. |
| 1.3.6.1.4.1.498.8.4.7.5 | snmp540RlLoopType | 1 | 1 | The value Pn127(1), will use a PN127 loopback sequence to initiate a remote loopback test. The value v54(2) will use a V54 loopba… |
| 1.3.6.1.4.1.498.8.4.7.6 | snmp540DiagBlocksToSend | 1 | 1 | Specifies the number of test pattern blocks to generate during the test. The requested number of blocks are sent and checked dur… |
| 1.3.6.1.4.1.498.8.4.7.7 | snmp540DiagControl | 1 | 1 | The lineloop(2) selection places the snmp540 into line loopback mode. The noTest(1) and telcoLoop(5) are READ ONLY values. NoTest… |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.498.8.4.1 | snmp540AlarmTrap, snmp540MIBversion | 1 | 1 | Identifies the version of the MIB. The format of the version is x.yzT, where 'x' identifies the major revision number, 'y'identif… |
| 1.3.6.1.4.1.498.8.4.2 | snmp540Config | 3 | 13 | None |
| 1.3.6.1.4.1.498.8.4.3 | snmp540Control | 1 | 2 | None |
| 1.3.6.1.4.1.498.8.4.4 | snmp540AlarmData | 18 | 18 | None |
| 1.3.6.1.4.1.498.8.4.5 | snmp540AlarmCfgThr | 2 | 6 | None |
| 1.3.6.1.4.1.498.8.4.6 | snmp540LineStats | 9 | 18 | None |
| 1.3.6.1.4.1.498.8.4.8 | snmp540Led | 1 | 2 | None |
| 1.3.6.1.4.1.498.8.4.9 | snmp540DeviceSerialNumber | 1 | 1 | Display's the unique serial number of this device. The octet string starts with the two byte product code (0540) followed by a re… |
| 1.3.6.1.4.1.498.8.4.10 | snmp540Alarm | 5 | 17 | None |