Specifies the number of test pattern blocks to
generate during the test. The requested number
of blocks are sent and checked during the test
as a means of verifying circuit and/or unit
integrity. Each block contains 1000 bits of test
pattern. The external selection specifies that
the test be invoked without any test pattern
block generation. The external(9) disables the
automatic test tear-down timer, and requires the
use of an external Bit Error Rate Tester(BERT).
!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!!
THE SNMP540 EXTERNAL(9) TEST SELECTION REQUIRES
A POWER-UP RESET TO END THE TEST !!
Parsed from file SNMP540.mib.txt
Company: None
Module: SNMP540-MGMT-MIB
Specifies the number of test pattern blocks to
generate during the test. The requested number
of blocks are sent and checked during the test
as a means of verifying circuit and/or unit
integrity. Each block contains 1000 bits of test
pattern. The external selection specifies that
the test be invoked without any test pattern
block generation. The external(9) disables the
automatic test tear-down timer, and requires the
use of an external Bit Error Rate Tester(BERT).
!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!!
THE SNMP540 EXTERNAL(9) TEST SELECTION REQUIRES
A POWER-UP RESET TO END THE TEST !!
Parsed from file SNMP540-MGMT-MIB.mib
Module: SNMP540-MGMT-MIB
snmp540DiagBlocksToSend OBJECT-TYPE SYNTAX INTEGER { blocks1(1), blocks10(2), blocks100(3), blocks500(4), blocks1000(5), blocks5000(6), blocks10000(7), blocks50000(8), external(9) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the number of test pattern blocks to generate during the test. The requested number of blocks are sent and checked during the test as a means of verifying circuit and/or unit integrity. Each block contains 1000 bits of test pattern. The external selection specifies that the test be invoked without any test pattern block generation. The external(9) disables the automatic test tear-down timer, and requires the use of an external Bit Error Rate Tester(BERT). !!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!! THE SNMP540 EXTERNAL(9) TEST SELECTION REQUIRES A POWER-UP RESET TO END THE TEST !!" ::= { snmp540DiagTest 6 }
Vendor: General DataComm, Inc.
Module: SNMP540-MGMT-MIB
[Automatically extracted from oidview.com]
snmp540DiagBlocksToSend OBJECT-TYPE SYNTAX INTEGER { blocks1(1), blocks10(2), blocks100(3), blocks500(4), blocks1000(5), blocks5000(6), blocks10000(7), blocks50000(8), external(9) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the number of test pattern blocks to generate during the test. The requested number of blocks are sent and checked during the test as a means of verifying circuit and/or unit integrity. Each block contains 1000 bits of test pattern. The external selection specifies that the test be invoked without any test pattern block generation. The external(9) disables the automatic test tear-down timer, and requires the use of an external Bit Error Rate Tester(BERT). !!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!! THE SNMP540 EXTERNAL(9) TEST SELECTION REQUIRES A POWER-UP RESET TO END THE TEST !!" ::= { snmp540DiagTest 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.498.8.4.7.6.0 | snmp540DiagBlocksToSend | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.498.8.4.7.1 | snmp540DiagTestPattern | 1 | 1 | The Self Test Pattern choices generated internally by the snmp540 are 511 Pattern (snmp540Send511Pattern(2)), 2047 pattern, (snmp5… |
| 1.3.6.1.4.1.498.8.4.7.2 | snmp540DiagTestExceptions | 1 | 1 | Indicates exceptions that have occurred that may affect interpretation of the test results. The exception values are: value excepti… |
| 1.3.6.1.4.1.498.8.4.7.3 | snmp540DiagBitErrors | 1 | 1 | The bit errors of the most recently run diagnostic test. If TestExceptions reports bitsOutOfRange, this object should be ignored. |
| 1.3.6.1.4.1.498.8.4.7.4 | snmp540DiagBlockErrors | 1 | 1 | The block errors of the most recently run diagnostic test. |
| 1.3.6.1.4.1.498.8.4.7.5 | snmp540RlLoopType | 1 | 1 | The value Pn127(1), will use a PN127 loopback sequence to initiate a remote loopback test. The value v54(2) will use a V54 loopba… |
| 1.3.6.1.4.1.498.8.4.7.7 | snmp540DiagControl | 1 | 1 | The lineloop(2) selection places the snmp540 into line loopback mode. The noTest(1) and telcoLoop(5) are READ ONLY values. NoTest… |