To initiate a Network Delay test SET this object and specifiy
runDelayTest. Both the remote (nms510) and master (sc5520) units
will go into a test to measure network delay. Emun 3
is write only. The only valid responses to a READ are delayTestOn(2)
or delayTestOff(1). This test will terminate after 10 seconds.
Test results should be read only after the test is
completed and are available from the master (sc5520) unit. The
current Test Status can be obtained by reading the sc5520DiagTestStatus
object on the master unit, reading test status on the remote unit may
interfere with the test and cause errors. This test can not be
terminated early once it is started.
Parsed from file nms510.mib.txt
Company: None
Module: NMS510-MIB
To initiate a Network Delay test SET this object and specifiy
runDelayTest. Both the remote (nms510) and master (sc5520) units
will go into a test to measure network delay. Emun 3
is write only. The only valid responses to a READ are delayTestOn(2)
or delayTestOff(1). This test will terminate after 10 seconds.
Test results should be read only after the test is
completed and are available from the master (sc5520) unit. The
current Test Status can be obtained by reading the sc5520DiagTestStatus
object on the master unit, reading test status on the remote unit may
interfere with the test and cause errors. This test can not be
terminated early once it is started.
Parsed from file NMS510-MIB.mib
Module: NMS510-MIB
nms510DiagNetworkDelay OBJECT-TYPE SYNTAX INTEGER { delayTestOff(1), delayTestOn(2), runDelayTest(3) } ACCESS read-write STATUS mandatory DESCRIPTION "To initiate a Network Delay test SET this object and specifiy runDelayTest. Both the remote (nms510) and master (sc5520) units will go into a test to measure network delay. Emun 3 is write only. The only valid responses to a READ are delayTestOn(2) or delayTestOff(1). This test will terminate after 10 seconds. Test results should be read only after the test is completed and are available from the master (sc5520) unit. The current Test Status can be obtained by reading the sc5520DiagTestStatus object on the master unit, reading test status on the remote unit may interfere with the test and cause errors. This test can not be terminated early once it is started." ::= { nms510DiagExcEntry 5 }
Vendor: General DataComm, Inc.
Module: NMS510-MIB
[Automatically extracted from oidview.com]
nms510DiagNetworkDelay OBJECT-TYPE SYNTAX INTEGER { delayTestOff(1), delayTestOn(2), runDelayTest(3) } ACCESS read-write STATUS mandatory DESCRIPTION "To initiate a Network Delay test SET this object and specifiy runDelayTest. Both the remote (nms510) and master (sc5520) units will go into a test to measure network delay. Emun 3 is write only. The only valid responses to a READ are delayTestOn(2) or delayTestOff(1). This test will terminate after 10 seconds. Test results should be read only after the test is completed and are available from the master (sc5520) unit. The current Test Status can be obtained by reading the sc5520DiagTestStatus object on the master unit, reading test status on the remote unit may interfere with the test and cause errors. This test can not be terminated early once it is started." ::= { nms510DiagExcEntry 5 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.498.8.6.7.1.1 | nms510DiagExcIndex | 0 | 0 | The index value which uniquely identifies the NMS510 to which this entry is applicable. This has the form of a SCinstance which … |
| 1.3.6.1.4.1.498.8.6.7.1.2 | nms510DiagIntLineloop | 0 | 0 | Lineloop (or Analoop) can be either a Bilaterial or Unilaterial loopback depending on option ddsDteTermaloop. To initiate a Line… |
| 1.3.6.1.4.1.498.8.6.7.1.3 | nms510DiagIntDataloop | 0 | 0 | To initiate a Dataloop with Selftest SET this object and specifiy a blocksize. The nms510 (the remote) unit will go into Dataloo… |
| 1.3.6.1.4.1.498.8.6.7.1.4 | nms510DiagEndToEndSelftest | 0 | 0 | To initiate an End to End Selftest(Error Rate Test) SET this object and specifiy a blocksize. Both the remote (nms510) amd maste… |
| 1.3.6.1.4.1.498.8.6.7.1.6 | nms510DiagTestStatus | 0 | 0 | This object gives the current diagonostic test status. noTest indicates that no diagonostic test is currently active. Reading thi… |
| 1.3.6.1.4.1.498.8.6.7.1.7 | nms510DiagExtDataloop | 0 | 0 | To initiate a Dataloop test with no Selftest SET this object and specifiy external, this will allow the data from the DTE attach… |