This attribute specifies the maximum number of Vpts that can be
activated on this AtmIf.
If the AtmIf is linked to a LogicalProcessor of cardType other than
3pE3Atm, 3pDS3Atm, 3pOC3MmAtm, 3pOC3SmAtm, 3pE1Atm,
3pDS1Atm, 2pJ6MAtm, the sum of (maxVccs + maxVpcs +
(maxVpts * 3) + 1) across all AtmIfs linked to that Lp must not
exceed the totalConnectionPoolCapacity attribute of the Arc
component. Note that 3 connections are used for every standard Vpt
and 2 for each basic Vpt. If the Arc component doesn't exist, the
default value of the Arc totalConnectionPoolCapacity attribute is
used as the limit.
Parsed from file nortelPP-atmCoreV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-AtmCoreMIB
This attribute specifies the maximum number of Vpts that can be
activated on this AtmIf.
If the AtmIf is linked to a LogicalProcessor of cardType other than
3pE3Atm, 3pDS3Atm, 3pOC3MmAtm, 3pOC3SmAtm, 3pE1Atm,
3pDS1Atm, 2pJ6MAtm, the sum of (maxVccs + maxVpcs +
(maxVpts * 3) + 1) across all AtmIfs linked to that Lp must not
exceed the totalConnectionPoolCapacity attribute of the Arc
component. Note that 3 connections are used for every standard Vpt
and 2 for each basic Vpt. If the Arc component doesn't exist, the
default value of the Arc totalConnectionPoolCapacity attribute is
used as the limit.
Parsed from file Nortel-Magellan-Passport-AtmCoreMIB.mib
Module: Nortel-Magellan-Passport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-AtmCoreMIB
[Automatically extracted from oidview.com]
atmIfCAMaxCaVpts OBJECT-TYPE SYNTAX Unsigned32 (0..4096) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the maximum number of Vpts that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProcessor of cardType other than 3pE3Atm, 3pDS3Atm, 3pOC3MmAtm, 3pOC3SmAtm, 3pE1Atm, 3pDS1Atm, 2pJ6MAtm, the sum of (maxVccs + maxVpcs + (maxVpts * 3) + 1) across all AtmIfs linked to that Lp must not exceed the totalConnectionPoolCapacity attribute of the Arc component. Note that 3 connections are used for every standard Vpt and 2 for each basic Vpt. If the Arc component doesn't exist, the default value of the Arc totalConnectionPoolCapacity attribute is used as the limit." DEFVAL { 128 } ::= { atmIfCAProvEntry 106 }
atmIfCAMaxCaVpts OBJECT-TYPE SYNTAX Unsigned32 (0..4096) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the maximum number of Vpts that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProcessor of cardType other than 3pE3Atm, 3pDS3Atm, 3pOC3MmAtm, 3pOC3SmAtm, 3pE1Atm, 3pDS1Atm, 2pJ6MAtm, the sum of (maxVccs + maxVpcs + (maxVpts * 3) + 1) across all AtmIfs linked to that Lp must not exceed the totalConnectionPoolCapacity attribute of the Arc component. Note that 3 connections are used for every standard Vpt and 2 for each basic Vpt. If the Arc component doesn't exist, the default value of the Arc totalConnectionPoolCapacity attribute is used as the limit." DEFVAL { 128 } ::= { atmIfCAProvEntry 106 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.5 | atmIfCAMaxVpcs | 0 | 0 | This attribute specifies the maximum number of Vpcs that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.6 | atmIfCAMaxVccs | 0 | 0 | This attribute specifies the maximum number of usable Vccs (and Vpt Vccs) that can be configured on this AtmIf. The value must n… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.7 | atmIfCAMinMulticastBranches | 0 | 0 | This attribute specifies the guaranteed number of multicast branches that can be activated on this AtmIf, including those activa… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.8 | atmIfCAMaxMulticastBranches | 0 | 0 | This attribute specifies the maximum number of provisionable multicast branches that can be activated on this AtmIf, including th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.9 | atmIfCAMaxVpts | 0 | 0 | This attribute specifies the maximum number of Vpts that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.10 | atmIfCAMinAutoSelectedVci | 0 | 0 | This attribute specifies the default lower boundary for VCIs which are automatically allocated for a switched Vcc. A VCI number … |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.15 | atmIfCAMinAutoSelectedVciForVpiZero | 0 | 0 | This attribute specifies the minimum VCIs value which will be automatically allocated for a switched Vcc with VPI value of zero.… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.20 | atmIfCAMinAutoSelectedVciForNonZeroVpi | 0 | 0 | This attribute specifies the minimum VCI value which will be automatically allocated for a switched Vcc with a non-zero VPI value… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.25 | atmIfCAPermittedSvcAtmServiceCategories | 0 | 0 | This attribute specifies which ATM service categories are permitted on this interface for SVCs. The value of this attribute does… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.30 | atmIfCACbrPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the constant bit rate (Cbr) service category. When th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.40 | atmIfCACbrCdvt | 0 | 0 | This attribute specifies the cell delay variation tolerance (CDVT) which is to be applied to the entire ATM Interface for Cbr tr… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.50 | atmIfCACbrCellLossRatio | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for Cbr traffic. The number is the logarithm (base 10) of the CLR. … |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.51 | atmIfCASvcCbrHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies for SVC Cbr connections. It takes a value from 0 (highest) t… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.52 | atmIfCASvcVbrRtHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies for SVC VbrRt connections. It takes a value from 0 (highest)… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.53 | atmIfCASvcVbrNrtHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies for SVC VbrNrt connections. It takes a value from 0 (highest… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.60 | atmIfCAVbrRtPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the variable bit rate real time (VbrRt) service categ… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.70 | atmIfCAVbrRtCdvt | 0 | 0 | This attribute specifies the cell delay variation tolerance (CDVT) which is to be applied to the entire ATM Interface for VbrRt … |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.80 | atmIfCAVbrRtCellLossRatio | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for VbrRt traffic. The number is the logarithm (base 10) of the CLR… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.90 | atmIfCAVbrNrtPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the variable bit rate non-real time (VbrNrt) service c… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.100 | atmIfCAVbrNrtCdvt | 0 | 0 | This attribute specifies the cell delay variation tolerance (CDVT), which is to be applied to the entire ATM Interface for VbrNr… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.105 | atmIfCAMaxCaVpcs | 0 | 0 | This attribute specifies the maximum number of Vpcs that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.110 | atmIfCAVbrNrtCellLossRatio | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for VbrNrt traffic. The number is the logarithm (base 10) of the CL… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.120 | atmIfCAUbrMaxConnections | 0 | 0 | This attribute specifies the maximum number of unspecified bit rate (UBR) connections which are to be admitted under this AtmIf.… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.121 | atmIfCAMinAutoSelectedVpi | 0 | 0 | This attribute specifies the minimum VPI value which will be automatically allocated for a switched Vpc. A VPI number is automati… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.122 | atmIfCAPermittedAtmServiceCategories | 0 | 0 | This attribute specifies which ATM service categories are permitted on this interface for SVPs and SVCs. The value of this attri… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.125 | atmIfCAMaxAutoSelectedVpi | 0 | 0 | This attribute specifies the maximumVPI value which will be automatically allocated for a switched Vpc or Vcc. A VPI number is au… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.126 | atmIfCAMaxAutoSelectedVciForVpiZero | 0 | 0 | This attribute specifies the maximum VCI value which is automatically allocated for a switched Vcc. A VCI number is automatically… |
| 1.3.6.1.4.1.562.2.4.1.114.3.100.1.127 | atmIfCAMaxAutoSelectedVciForNonZeroVpi | 0 | 0 | This attribute specifies the maximum VCI value which is automatically allocated for a switched Vcc. A VCI number is automatically… |