This attribute specifies the tolerable cell loss ratio (CLR) for
VbrNrt traffic. The number is the logarithm (base 10) of the CLR.
In other words if the target CLR = 1E-10 then vbrNrtCellLossRatio
= -10.This number must be greater than or equal to
vbrRtCellLossRatio since VbrRt traffic has a higher discard
priority. The vbrNrtCellLossRatio is used by the Connection
Admission Control (CAC) algorithm to compute the required
(equivalent) cell rate for VbrNrt connections.
There is a trade-off between the service category CLR and the
achievable link utilization. To guarantee an excellent service
category, the CLR should be as small as possible (e.g., 1E-10).
However, a smaller CLR results in a larger equivalent cell rate for a
given connection and hence a lower link utilization.
Parsed from file nortelPP-atmBaseV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-AtmBaseMIB
This attribute has been obsoleted and migrated under the NrtVbr
subcomponent. In addition, the type and range of new attribute has
been changed.
This attribute specifies the tolerable cell loss ratio (CLR) for nrt-
VBR traffic. The number is the logarithm (base 10) of the CLR. In
other words if the target CLR = 1E-10 then vbrNrtCellLossRatio = -
10.This number must be greater than or equal to
vbrRtCellLossRatio since rt-VBR traffic has a higher discard
priority. The vbrNrtCellLossRatio is used by the Connection
Admission Control (CAC) algorithm to compute the required
(equivalent) cell rate for nrt-VBR connections.
There is a trade-off between the service category CLR and the
achievable link utilization. To guarantee an excellent service
category, the CLR should be as small as possible (e.g., 1E-10).
However, a smaller CLR results in a larger equivalent cell rate for a
given connection and hence a lower link utilization.
Parsed from file Nortel-Magellan-Passport-AtmCoreMIB.mib
Module: Nortel-Magellan-Passport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-AtmCoreMIB
[Automatically extracted from oidview.com]
atmIfCAVbrNrtCellLossRatio OBJECT-TYPE SYNTAX INTEGER (-10..0) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the tolerable cell loss ratio (CLR) for VbrNrt traffic. The number is the logarithm (base 10) of the CLR. In other words if the target CLR = 1E-10 then vbrNrtCellLossRatio = -10.This number must be greater than or equal to vbrRtCellLossRatio since VbrRt traffic has a higher discard priority. The vbrNrtCellLossRatio is used by the Connection Admission Control (CAC) algorithm to compute the required (equivalent) cell rate for VbrNrt connections. There is a trade-off between the service category CLR and the achievable link utilization. To guarantee an excellent service category, the CLR should be as small as possible (e.g., 1E-10). However, a smaller CLR results in a larger equivalent cell rate for a given connection and hence a lower link utilization." DEFVAL { -7 } ::= { atmIfCAProvEntry 110 }
atmIfCAVbrNrtCellLossRatio OBJECT-TYPE SYNTAX INTEGER (-10..0) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute has been obsoleted and migrated under the NrtVbr subcomponent. In addition, the type and range of new attribute has been changed. This attribute specifies the tolerable cell loss ratio (CLR) for nrt- VBR traffic. The number is the logarithm (base 10) of the CLR. In other words if the target CLR = 1E-10 then vbrNrtCellLossRatio = - 10.This number must be greater than or equal to vbrRtCellLossRatio since rt-VBR traffic has a higher discard priority. The vbrNrtCellLossRatio is used by the Connection Admission Control (CAC) algorithm to compute the required (equivalent) cell rate for nrt-VBR connections. There is a trade-off between the service category CLR and the achievable link utilization. To guarantee an excellent service category, the CLR should be as small as possible (e.g., 1E-10). However, a smaller CLR results in a larger equivalent cell rate for a given connection and hence a lower link utilization." DEFVAL { -7 } ::= { atmIfCAProvEntry 110 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.562.2.4.1.114.3.100.1.5 | atmIfCAMaxVpcs | 0 | 0 | This attribute specifies the maximum number of Vpcs that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.6 | atmIfCAMaxVccs | 0 | 0 | This attribute specifies the maximum number of usable Vccs (and Vpt Vccs) that can be configured on this AtmIf. The value must n… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.7 | atmIfCAMinMulticastBranches | 0 | 0 | This attribute specifies the guaranteed number of multicast branches that can be activated on this AtmIf, including those activa… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.8 | atmIfCAMaxMulticastBranches | 0 | 0 | This attribute specifies the maximum number of provisionable multicast branches that can be activated on this AtmIf, including th… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.9 | atmIfCAMaxVpts | 0 | 0 | This attribute specifies the maximum number of Vpts that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.10 | atmIfCAMinAutoSelectedVci | 0 | 0 | This attribute specifies the default lower boundary for VCIs which are automatically allocated for a switched Vcc. A VCI number … |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.15 | atmIfCAMinAutoSelectedVciForVpiZero | 0 | 0 | This attribute specifies the minimum VCIs value which will be automatically allocated for a switched Vcc with VPI value of zero.… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.20 | atmIfCAMinAutoSelectedVciForNonZeroVpi | 0 | 0 | This attribute specifies the minimum VCI value which will be automatically allocated for a switched Vcc with a non-zero VPI value… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.25 | atmIfCAPermittedSvcAtmServiceCategories | 0 | 0 | This attribute specifies which ATM service categories are permitted on this interface for SVCs. The value of this attribute does… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.30 | atmIfCACbrPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the constant bit rate (Cbr) service category. When th… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.40 | atmIfCACbrCdvt | 0 | 0 | This attribute specifies the cell delay variation tolerance (CDVT) which is to be applied to the entire ATM Interface for Cbr tr… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.50 | atmIfCACbrCellLossRatio | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for Cbr traffic. The number is the logarithm (base 10) of the CLR. … |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.51 | atmIfCASvcCbrHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies for SVC Cbr connections. It takes a value from 0 (highest) t… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.52 | atmIfCASvcVbrRtHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies for SVC VbrRt connections. It takes a value from 0 (highest)… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.53 | atmIfCASvcVbrNrtHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies for SVC VbrNrt connections. It takes a value from 0 (highest… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.60 | atmIfCAVbrRtPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the variable bit rate real time (VbrRt) service categ… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.70 | atmIfCAVbrRtCdvt | 0 | 0 | This attribute specifies the cell delay variation tolerance (CDVT) which is to be applied to the entire ATM Interface for VbrRt … |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.80 | atmIfCAVbrRtCellLossRatio | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for VbrRt traffic. The number is the logarithm (base 10) of the CLR… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.90 | atmIfCAVbrNrtPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the variable bit rate non-real time (VbrNrt) service c… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.100 | atmIfCAVbrNrtCdvt | 0 | 0 | This attribute specifies the cell delay variation tolerance (CDVT), which is to be applied to the entire ATM Interface for VbrNr… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.105 | atmIfCAMaxCaVpcs | 0 | 0 | This attribute specifies the maximum number of Vpcs that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.106 | atmIfCAMaxCaVpts | 0 | 0 | This attribute specifies the maximum number of Vpts that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.120 | atmIfCAUbrMaxConnections | 0 | 0 | This attribute specifies the maximum number of unspecified bit rate (UBR) connections which are to be admitted under this AtmIf.… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.121 | atmIfCAMinAutoSelectedVpi | 0 | 0 | This attribute specifies the minimum VPI value which will be automatically allocated for a switched Vpc. A VPI number is automati… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.122 | atmIfCAPermittedAtmServiceCategories | 0 | 0 | This attribute specifies which ATM service categories are permitted on this interface for SVPs and SVCs. The value of this attri… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.125 | atmIfCAMaxAutoSelectedVpi | 0 | 0 | This attribute specifies the maximumVPI value which will be automatically allocated for a switched Vpc or Vcc. A VPI number is au… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.126 | atmIfCAMaxAutoSelectedVciForVpiZero | 0 | 0 | This attribute specifies the maximum VCI value which is automatically allocated for a switched Vcc. A VCI number is automatically… |
1.3.6.1.4.1.562.2.4.1.114.3.100.1.127 | atmIfCAMaxAutoSelectedVciForNonZeroVpi | 0 | 0 | This attribute specifies the maximum VCI value which is automatically allocated for a switched Vcc. A VCI number is automatically… |