This attribute displays whether the application is set to tolerate
momentary interruption of a path while a new path is selected. If
disconnectConnection is displayed, the application is informed as
soon as possible about a failure by disconnection. If the attribute
displays reRoutePath, the path may attempt an immediate reroute,
provided the failure is a recoverable failure. If rerouting fails the
application is informed of the failure.
With this option set to reRoutePath the LCo may wait up to 30
seconds before informing the service of complete disconnection in
order to allow both ends to attempt to reconnect. Note that if PLC
components are different at both ends only the calling end is
allowed to reconnect.
All pathTypes respect this attribute. Also on a manualPath with
both ends provisioned with independent paths (at least with respect
to the failure) this option will have the desired effect that the path is
rerouted without complete disconnection at both ends
Parsed from file nortelPP-circuitEmulationServiceV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-CircuitEmulationServiceMIB
This attribute displays whether the application is set to tolerate
momentary interruption of a path while a new path is selected. If
disconnectConnection is displayed, the application is informed as
soon as possible about a failure by disconnection. If the attribute
displays reRoutePath, the path may attempt an immediate reroute,
provided the failure is a recoverable failure. If rerouting fails the
application is informed of the failure.
With this option set to reRoutePath the LCo may wait up to 30
seconds before informing the service of complete disconnection in
order to allow both ends to attempt to reconnect. Note that if PLC
components are different at both ends only the calling end is
allowed to reconnect.
All pathTypes respect this attribute. Also on a manualPath with
both ends provisioned with independent paths (at least with respect
to the failure) this option will have the desired effect that the path is
rerouted without complete disconnection at both ends
Parsed from file Nortel-Magellan-Passport-CircuitEmulationServiceMIB.mib
Module: Nortel-Magellan-Passport-CircuitEmulationServiceMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-CircuitEmulationServiceMIB
[Automatically extracted from oidview.com]
aal1CesLCoPathFailureAction OBJECT-TYPE SYNTAX INTEGER { disconnectConnection(0), reRoutePath(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether the application is set to tolerate momentary interruption of a path while a new path is selected. If disconnectConnection is displayed, the application is informed as soon as possible about a failure by disconnection. If the attribute displays reRoutePath, the path may attempt an immediate reroute, provided the failure is a recoverable failure. If rerouting fails the application is informed of the failure. With this option set to reRoutePath the LCo may wait up to 30 seconds before informing the service of complete disconnection in order to allow both ends to attempt to reconnect. Note that if PLC components are different at both ends only the calling end is allowed to reconnect. All pathTypes respect this attribute. Also on a manualPath with both ends provisioned with independent paths (at least with respect to the failure) this option will have the desired effect that the path is rerouted without complete disconnection at both ends" ::= { aal1CesLCoPathDataEntry 22 }
aal1CesLCoPathFailureAction OBJECT-TYPE SYNTAX INTEGER { disconnectConnection(0), reRoutePath(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether the application is set to tolerate momentary interruption of a path while a new path is selected. If disconnectConnection is displayed, the application is informed as soon as possible about a failure by disconnection. If the attribute displays reRoutePath, the path may attempt an immediate reroute, provided the failure is a recoverable failure. If rerouting fails the application is informed of the failure. With this option set to reRoutePath the LCo may wait up to 30 seconds before informing the service of complete disconnection in order to allow both ends to attempt to reconnect. Note that if PLC components are different at both ends only the calling end is allowed to reconnect. All pathTypes respect this attribute. Also on a manualPath with both ends provisioned with independent paths (at least with respect to the failure) this option will have the desired effect that the path is rerouted without complete disconnection at both ends" ::= { aal1CesLCoPathDataEntry 22 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.1 | aal1CesLCoState | 0 | 0 | This attribute reflects the current state of the connection. The pathDown state indicates a connection that has no remote end pro… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.2 | aal1CesLCoOverrideRemoteName | 0 | 0 | If set and the current PLC remoteName is blank this remoteName will override the blank PLC remoteName. Usually you would set this… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.3 | aal1CesLCoEnd | 0 | 0 | This attribute identifies whether this is the calling or called end of the path. |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.4 | aal1CesLCoCostMetric | 0 | 0 | This attribute gives the route's total cost metric. It is calculated as the sum of the cost metric of all trunks in the path at … |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.5 | aal1CesLCoDelayMetric | 0 | 0 | This attribute gives the total delay of the route as the one way delay for a 512 byte packet. It is calculated as the sum of the… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.6 | aal1CesLCoRoundTripDelay | 0 | 0 | This attribute contains the time taken for a packet (cell) of 44 bytes to be transmitted to the remote LCo and return to this LC… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.7 | aal1CesLCoSetupPriority | 0 | 0 | This attribute gives the priority at which the current path is established. Zero is the highest priority and four is the lowest.… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.8 | aal1CesLCoHoldingPriority | 0 | 0 | This attribute gives the priority at which a path holds its current path once the path is established. Zero is the highest prior… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.9 | aal1CesLCoRequiredTxBandwidth | 0 | 0 | This attribute gives the actual bandwidth (in bits per second) reserved by this path on each of the trunks of its route. This at… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.10 | aal1CesLCoRequiredRxBandwidth | 0 | 0 | This attribute gives the actual bandwidth (in bits per second) reserved by this path on each of trunks of its route. This attrib… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.11 | aal1CesLCoRequiredTrafficType | 0 | 0 | This operational attribute indicates the type of traffic transmitted over the path. There are eight possible traffic types, and … |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.12 | aal1CesLCoPermittedTrunkTypes | 0 | 0 | This operational attribute lists up to eight types of trunk that can be used on the route. The originating end of the connection… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.13 | aal1CesLCoRequiredSecurity | 0 | 0 | This attribute indicates the required minimum level of security of the trunks on the route. Zero represents the most secure and … |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.14 | aal1CesLCoRequiredCustomerParameter | 0 | 0 | This attribute indicates the allowed customer defined parameter of the trunks on the route.The originating end of the connection… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.15 | aal1CesLCoEmissionPriority | 0 | 0 | This attribute indicates the urgency with which packets on the path are emitted by the trunks on the route. The originating end … |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.16 | aal1CesLCoDiscardPriority | 0 | 0 | This attribute indicates the importance of the packets on the path.The originating end of the connection sets discardPriority. O… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.17 | aal1CesLCoPathType | 0 | 0 | aal1CesLCoPathtype |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.18 | aal1CesLCoRetryCount | 0 | 0 | This attribute is the count of the number of times the path chosen during route selection could not be instantiated. This count … |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.19 | aal1CesLCoPathFailureCount | 0 | 0 | This attribute is the count of the number of times the path has successfully connected. It is set to zero the first time the pat… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.20 | aal1CesLCoReasonForNoRoute | 0 | 0 | This attribute is the route selection's reasonForNoRoute and provides a brief reason for which a route was not selected. The reas… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.21 | aal1CesLCoLastTearDownReason | 0 | 0 | This attribute reflects the last tear down reason for a connection (LCo). In many cases this displays the reason for a momentary… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.23 | aal1CesLCoBumpPreference | 0 | 0 | This attribute specifies when bumping will occur during route selection process. Bumping may occur when necessary or always. It w… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.24 | aal1CesLCoOptimization | 0 | 0 | This attribute is used to specify whether this connection should attempt to optimize its path when requested by the routing PORS… |
| 1.3.6.1.4.1.562.2.4.1.119.5.10.1.25 | aal1CesLCoPathUpDateTime | 0 | 0 | This is the time stamp when the current path was established or reestablished. |