This attribute displays whether a Loss Of Signal (LOS) alarm state
has been entered. An LOS alarm state is entered when LOS defects
has been observed and accumulated for a period of 2.5 seconds +/-
0.5 seconds. An LOS defect is detected at the E3 line interface upon
observing N continuous pulse positions with no pulses of either
positive or negative polarity, where N is between 10 and 255. If the
LOS defects are intermittently occurring, the LOS defect
accumulator is decremented at a rate of 1/10 of the incrementing
rate (alarm integration ratio of 1/10), with all measurements based
on a 200 ms polling cycle.
The E3 component goes into an operational state of disabled until
the LOS alarm condition is cleared. The LOS alarm state is cleared
when the LOS defects are absent for a period of 10 seconds +/- 0.5
seconds.
The losAlarm attribute is always set to off when the component has
been locked and left offline.
Parsed from file nortelPP-logicalProcessorV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
This attribute displays whether a Loss Of Signal (LOS) alarm state
has been entered. An LOS alarm state is entered when LOS defects
has been observed and accumulated for a period of 2.5 seconds +/-
0.5 seconds. An LOS defect is detected at the E3 line interface upon
observing N continuous pulse positions with no pulses of either
positive or negative polarity, where N is between 10 and 255. If the
LOS defects are intermittently occurring, the LOS defect
accumulator is decremented at a rate of 1/10 of the incrementing
rate (alarm integration ratio of 1/10), with all measurements based
on a 200 ms polling cycle.
The E3 component goes into an operational state of disabled until
the LOS alarm condition is cleared. The LOS alarm state is cleared
when the LOS defects are absent for a period of 10 seconds +/- 0.5
seconds.
The losAlarm attribute is always set to off when the component has
been locked and left offline.
Parsed from file Nortel-Magellan-Passport-LogicalProcessorMIB.mib
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
[Automatically extracted from oidview.com]
lpE3LosAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a Loss Of Signal (LOS) alarm state has been entered. An LOS alarm state is entered when LOS defects has been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. An LOS defect is detected at the E3 line interface upon observing N continuous pulse positions with no pulses of either positive or negative polarity, where N is between 10 and 255. If the LOS defects are intermittently occurring, the LOS defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The E3 component goes into an operational state of disabled until the LOS alarm condition is cleared. The LOS alarm state is cleared when the LOS defects are absent for a period of 10 seconds +/- 0.5 seconds. The losAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { lpE3OperEntry 1 }
lpE3LosAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a Loss Of Signal (LOS) alarm state has been entered. An LOS alarm state is entered when LOS defects has been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. An LOS defect is detected at the E3 line interface upon observing N continuous pulse positions with no pulses of either positive or negative polarity, where N is between 10 and 255. If the LOS defects are intermittently occurring, the LOS defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The E3 component goes into an operational state of disabled until the LOS alarm condition is cleared. The LOS alarm state is cleared when the LOS defects are absent for a period of 10 seconds +/- 0.5 seconds. The losAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { lpE3OperEntry 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.2 | lpE3LofAlarm | 0 | 0 | This attribute displays whether a Loss Of Frame (LOF) alarm state has been entered. An LOF alarm state is entered when Severely E… |
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.3 | lpE3RxAisAlarm | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm when state has been entered. An AIS alarm state is entere… |
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.4 | lpE3RxRaiAlarm | 0 | 0 | This attribute displays whether a Remote Alarm Indication (RAI) alarm state has been entered. A RAI alarm state is entered when … |
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.5 | lpE3TxAis | 0 | 0 | This attribute displays whether an AIS alarm is being transmitted on the E3 line. AIS is transmitted on the outgoing line when t… |
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.6 | lpE3TxRai | 0 | 0 | This attribute displays whether the far-end SEF/AIS defect indicator is transmitted over the outgoing line when the E3 component… |