This attribute displays whether a Remote Alarm Indication (RAI)
alarm state has been entered. A RAI alarm state is entered when far-
end SEF/AIS defects (or Far-End Receive Failure (FERF) defects in
G.832 E3 Framing mode) have been observed and accumulated for
a period of 2.5 seconds +/- 0.5 seconds on the E3 incoming line. If
the RAI defects are intermittently occurring, the RAI defect
accumulator is decremented at a rate of 1/10 of the incrementing
rate (alarm integration ratio of 1/10), with all measurements based
on a 200 ms polling cycle.
The E3 component goes into an operational state of disabled until
the RAI alarm condition is cleared. The condition is cleared when
the far-end defect indicator has not been detected for 10 seconds +/-
0.5 seconds. The declaration of a RAI Alarm is usually a signal that
the far end facility is unable to gain synchronization.
The rxRaiAlarm attribute is always set to off when the component
has been locked and left offline.
Parsed from file nortelPP-logicalProcessorV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
This attribute displays whether a Remote Alarm Indication (RAI)
alarm state has been entered. A RAI alarm state is entered when far-
end SEF/AIS defects (or Far-End Receive Failure (FERF) defects in
G.832 E3 Framing mode) have been observed and accumulated for
a period of 2.5 seconds +/- 0.5 seconds on the E3 incoming line. If
the RAI defects are intermittently occurring, the RAI defect
accumulator is decremented at a rate of 1/10 of the incrementing
rate (alarm integration ratio of 1/10), with all measurements based
on a 200 ms polling cycle.
The E3 component goes into an operational state of disabled until
the RAI alarm condition is cleared. The condition is cleared when
the far-end defect indicator has not been detected for 10 seconds +/-
0.5 seconds. The declaration of a RAI Alarm is usually a signal that
the far end facility is unable to gain synchronization.
The rxRaiAlarm attribute is always set to off when the component
has been locked and left offline.
Parsed from file Nortel-Magellan-Passport-LogicalProcessorMIB.mib
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
[Automatically extracted from oidview.com]
lpE3RxRaiAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a Remote Alarm Indication (RAI) alarm state has been entered. A RAI alarm state is entered when far- end SEF/AIS defects (or Far-End Receive Failure (FERF) defects in G.832 E3 Framing mode) have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds on the E3 incoming line. If the RAI defects are intermittently occurring, the RAI defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The E3 component goes into an operational state of disabled until the RAI alarm condition is cleared. The condition is cleared when the far-end defect indicator has not been detected for 10 seconds +/- 0.5 seconds. The declaration of a RAI Alarm is usually a signal that the far end facility is unable to gain synchronization. The rxRaiAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { lpE3OperEntry 4 }
lpE3RxRaiAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a Remote Alarm Indication (RAI) alarm state has been entered. A RAI alarm state is entered when far- end SEF/AIS defects (or Far-End Receive Failure (FERF) defects in G.832 E3 Framing mode) have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds on the E3 incoming line. If the RAI defects are intermittently occurring, the RAI defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The E3 component goes into an operational state of disabled until the RAI alarm condition is cleared. The condition is cleared when the far-end defect indicator has not been detected for 10 seconds +/- 0.5 seconds. The declaration of a RAI Alarm is usually a signal that the far end facility is unable to gain synchronization. The rxRaiAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { lpE3OperEntry 4 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.1 | lpE3LosAlarm | 0 | 0 | This attribute displays whether a Loss Of Signal (LOS) alarm state has been entered. An LOS alarm state is entered when LOS defe… |
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.2 | lpE3LofAlarm | 0 | 0 | This attribute displays whether a Loss Of Frame (LOF) alarm state has been entered. An LOF alarm state is entered when Severely E… |
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.3 | lpE3RxAisAlarm | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm when state has been entered. An AIS alarm state is entere… |
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.5 | lpE3TxAis | 0 | 0 | This attribute displays whether an AIS alarm is being transmitted on the E3 line. AIS is transmitted on the outgoing line when t… |
| 1.3.6.1.4.1.562.2.4.1.12.6.16.1.6 | lpE3TxRai | 0 | 0 | This attribute displays whether the far-end SEF/AIS defect indicator is transmitted over the outgoing line when the E3 component… |