This attribute is not applicable and is ignored for CQC-based ATM
cards.
This attribute specifies the emission priority (EP) which is used to
transmit traffic of the UBR service category. A lower numerical
value for this attribute specifies a higher emission priority. 0 is the
highest EP and 7 is the lowest. Cells at a higher emission priority
receive higher preference for link bandwidth. EPs 0 and 1 are in the
absolute priority range, and are unaffected by any minimum
bandwidth guarantees. EPs 2 through 7 are in the guaranteed
bandwidth range. Minimum bandwidth guarantee is specified in the
AtmIf/n Ep/m component.
Emission priority setting must comply with all of the following
constraints:
1. The emission priority numbers must be in the following order:
CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR
2. Two different ATM service categories may share the same EP
only if they are both shaped.
3. CBR and rt-VBR may be placed either in the absolute priority
range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2
through 7).
4. If both CBR and rt-VBR are shaped, rt-VBR must share the
same EP with CBR or ABR. If either one of CBR or rt-VBR are
not shaped, then they cannot share the same EP.
5. ABR service category is always deemed to be shaped. If nrt-VBR
is shaped, it must share the same EP with ABR. If nrt-VBR is not
shaped it must have a higher EP than ABR.
6. If UBR is shaped, it must share the same EP with ABR. If UBR
is not shaped, it must have a lower EP than ABR.
This attribute does not apply to basic Vpts, and standard Vpt Vccs.
Parsed from file nortelPC-atmCoreV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
This attribute is not applicable and is ignored for CQC-based ATM
cards.
This attribute specifies the emission priority (EP) which is used to
transmit traffic of the UBR service category. A lower numerical
value for this attribute specifies a higher emission priority. 0 is the
highest EP and 7 is the lowest. Cells at a higher emission priority
receive higher preference for link bandwidth. EPs 0 and 1 are in the
absolute priority range, and are unaffected by any minimum
bandwidth guarantees. EPs 2 through 7 are in the guaranteed
bandwidth range. Minimum bandwidth guarantee is specified in the
AtmIf/n Ep/m component.
Emission priority setting must comply with all of the following
constraints:
1. The emission priority numbers must be in the following order:
CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR
2. Two different ATM service categories may share the same EP
only if they are both shaped.
3. CBR and rt-VBR may be placed either in the absolute priority
range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2
through 7).
4. If both CBR and rt-VBR are shaped, rt-VBR must share the
same EP with CBR or ABR. If either one of CBR or rt-VBR are
not shaped, then they cannot share the same EP.
5. ABR service category is always deemed to be shaped. If nrt-VBR
is shaped, it must share the same EP with ABR. If nrt-VBR is not
shaped it must have a higher EP than ABR.
6. If UBR is shaped, it must share the same EP with ABR. If UBR
is not shaped, it must have a lower EP than ABR.
This attribute does not apply to basic Vpts, and standard Vpt Vccs.
Parsed from file Nortel-MsCarrier-MscPassport-AtmCoreMIB.mib
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
[Automatically extracted from oidview.com]
mscAtmIfCAUbrEmissionPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) which is used to transmit traffic of the UBR service category. A lower numerical value for this attribute specifies a higher emission priority. 0 is the highest EP and 7 is the lowest. Cells at a higher emission priority receive higher preference for link bandwidth. EPs 0 and 1 are in the absolute priority range, and are unaffected by any minimum bandwidth guarantees. EPs 2 through 7 are in the guaranteed bandwidth range. Minimum bandwidth guarantee is specified in the AtmIf/n Ep/m component. Emission priority setting must comply with all of the following constraints: 1. The emission priority numbers must be in the following order: CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR 2. Two different ATM service categories may share the same EP only if they are both shaped. 3. CBR and rt-VBR may be placed either in the absolute priority range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2 through 7). 4. If both CBR and rt-VBR are shaped, rt-VBR must share the same EP with CBR or ABR. If either one of CBR or rt-VBR are not shaped, then they cannot share the same EP. 5. ABR service category is always deemed to be shaped. If nrt-VBR is shaped, it must share the same EP with ABR. If nrt-VBR is not shaped it must have a higher EP than ABR. 6. If UBR is shaped, it must share the same EP with ABR. If UBR is not shaped, it must have a lower EP than ABR. This attribute does not apply to basic Vpts, and standard Vpt Vccs." DEFVAL { 7 } ::= { mscAtmIfCAUbrProvEntry 15 }
mscAtmIfCAUbrEmissionPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) which is used to transmit traffic of the UBR service category. A lower numerical value for this attribute specifies a higher emission priority. 0 is the highest EP and 7 is the lowest. Cells at a higher emission priority receive higher preference for link bandwidth. EPs 0 and 1 are in the absolute priority range, and are unaffected by any minimum bandwidth guarantees. EPs 2 through 7 are in the guaranteed bandwidth range. Minimum bandwidth guarantee is specified in the AtmIf/n Ep/m component. Emission priority setting must comply with all of the following constraints: 1. The emission priority numbers must be in the following order: CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR 2. Two different ATM service categories may share the same EP only if they are both shaped. 3. CBR and rt-VBR may be placed either in the absolute priority range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2 through 7). 4. If both CBR and rt-VBR are shaped, rt-VBR must share the same EP with CBR or ABR. If either one of CBR or rt-VBR are not shaped, then they cannot share the same EP. 5. ABR service category is always deemed to be shaped. If nrt-VBR is shaped, it must share the same EP with ABR. If nrt-VBR is not shaped it must have a higher EP than ABR. 6. If UBR is shaped, it must share the same EP with ABR. If UBR is not shaped, it must have a lower EP than ABR. This attribute does not apply to basic Vpts, and standard Vpt Vccs." DEFVAL { 7 } ::= { mscAtmIfCAUbrProvEntry 15 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.5 | mscAtmIfCAUbrMaxVpcs | 0 | 0 | This attribute specifies the maximum number of UBR Vpcs that can be activated on this AtmIf. The value must not exceed the maxVp… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.6 | mscAtmIfCAUbrMaxVccs | 0 | 0 | This attribute specifies the maximum number of UBR Vccs that can be activated on this AtmIf, including UBR Vpt Vccs. The value m… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.7 | mscAtmIfCAUbrMaxVpts | 0 | 0 | This attribute specifies the maximum number of UBR Vpts that can be activated on this AtmIf. The value must not exceed the maxVp… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.10 | mscAtmIfCAUbrPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the unspecified bit rate (UBR) service category excep… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.11 | mscAtmIfCAUbrMinimumCellRate | 0 | 0 | This attribute specifies the minimum cell rate (MCR) which is allocated from the UBR bandwidth pool for each UBR connection which… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.12 | mscAtmIfCAUbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the UBR service c… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.13 | mscAtmIfCAUbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the UBR service category. The queue lim… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.14 | mscAtmIfCAUbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the UB… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.19 | mscAtmIfCAUbrTrafficShaping | 0 | 0 | This attribute specifies the default traffic shaping option for connections of the UBR service category. An override to this def… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.20 | mscAtmIfCAUbrShapeRecoupPolicy | 0 | 0 | This attribute specifies the shaping recoup policy for the UBR service category. This is the policy which is used to recoup shap… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.21 | mscAtmIfCAUbrUnshapedTransmitQueueing | 0 | 0 | This attribute specifies the default queuing option for unshaped connections of the UBR service category. This attribute control… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.22 | mscAtmIfCAUbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the UBR service category. This attr… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.23 | mscAtmIfCAUbrWeightPolicy | 0 | 0 | This attribute specifies the policy which is applied when calculating the fairness weight for unshaped connections of the UBR se… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.24 | mscAtmIfCAUbrForceTagging | 0 | 0 | This attribute specifies the default of whether to force tagging (CLP=1) of all cells for all UBR connections. An override to th… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.30 | mscAtmIfCAUbrCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the UBR service category. An ov… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.40 | mscAtmIfCAUbrHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVP and SVC UBR connections. It takes a value from 0 (hig… |
1.3.6.1.4.1.562.36.2.1.114.3.6.100.1.50 | mscAtmIfCAUbrSvcMpHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC UBR point-to-multipoint connections. It takes a value… |