This attribute displays whether the Path Remote Failure Indication
(P-RFI) alarm state has been entered. An P-RFI alarm state is
entered when Path Remote Defect Indicator (P-RDI) defects have
been observed and accumulated for a period of 2.5 seconds +/- 0.5
seconds. The P-RDI defect is the occurrence of the P-RDI signal in
five contiguous valid STS or STM frames (bit 5 of the G1 byte set
to 1). If the P-RDI defects are intermittently occurring, the P-RDI
defect accumulator is decremented at a rate of 1/10 of the
incrementing rate (alarm integration ratio of 1/10)with all
measurements based on a 200 ms polling cycle.
The Path component goes into an operational state of disabled until
the P-RFI alarm condition is cleared. The condition is cleared after
no P-RDI defect has been detected for 10 seconds +/- 0.5 seconds.
The rxRfiAlarm attribute is always set to off when the Path
component has been locked and left offline by the operator or when
the Path component has been suspended since the parent component
has been locked.
Parsed from file nortelPC-logicalProcessorV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
This attribute displays whether the Path Remote Failure Indication
(P-RFI) alarm state has been entered. An P-RFI alarm state is
entered when Path Remote Defect Indicator (P-RDI) defects have
been observed and accumulated for a period of 2.5 seconds +/- 0.5
seconds. The P-RDI defect is the occurrence of the P-RDI signal in
five contiguous valid STS or STM frames (bit 5 of the G1 byte set
to 1). If the P-RDI defects are intermittently occurring, the P-RDI
defect accumulator is decremented at a rate of 1/10 of the
incrementing rate (alarm integration ratio of 1/10)with all
measurements based on a 200 ms polling cycle.
The Path component goes into an operational state of disabled until
the P-RFI alarm condition is cleared. The condition is cleared after
no P-RDI defect has been detected for 10 seconds +/- 0.5 seconds.
The rxRfiAlarm attribute is always set to off when the Path
component has been locked and left offline by the operator or when
the Path component has been suspended since the parent component
has been locked.
Parsed from file Nortel-MsCarrier-MscPassport-LogicalProcessorMIB.mib
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
[Automatically extracted from oidview.com]
mscLpSonetPathRxRfiAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether the Path Remote Failure Indication (P-RFI) alarm state has been entered. An P-RFI alarm state is entered when Path Remote Defect Indicator (P-RDI) defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. The P-RDI defect is the occurrence of the P-RDI signal in five contiguous valid STS or STM frames (bit 5 of the G1 byte set to 1). If the P-RDI defects are intermittently occurring, the P-RDI defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10)with all measurements based on a 200 ms polling cycle. The Path component goes into an operational state of disabled until the P-RFI alarm condition is cleared. The condition is cleared after no P-RDI defect has been detected for 10 seconds +/- 0.5 seconds. The rxRfiAlarm attribute is always set to off when the Path component has been locked and left offline by the operator or when the Path component has been suspended since the parent component has been locked." ::= { mscLpSonetPathOperEntry 3 }
mscLpSonetPathRxRfiAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether the Path Remote Failure Indication (P-RFI) alarm state has been entered. An P-RFI alarm state is entered when Path Remote Defect Indicator (P-RDI) defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. The P-RDI defect is the occurrence of the P-RDI signal in five contiguous valid STS or STM frames (bit 5 of the G1 byte set to 1). If the P-RDI defects are intermittently occurring, the P-RDI defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10)with all measurements based on a 200 ms polling cycle. The Path component goes into an operational state of disabled until the P-RFI alarm condition is cleared. The condition is cleared after no P-RDI defect has been detected for 10 seconds +/- 0.5 seconds. The rxRfiAlarm attribute is always set to off when the Path component has been locked and left offline by the operator or when the Path component has been suspended since the parent component has been locked." ::= { mscLpSonetPathOperEntry 3 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.12.14.2.15.1.1 | mscLpSonetPathLopAlarm | 0 | 0 | This attribute displays whether a Loss Of Pointer (LOP) alarm state has been entered. An LOP alarm state is entered when LOP def… |
| 1.3.6.1.4.1.562.36.2.1.12.14.2.15.1.2 | mscLpSonetPathRxAisAlarm | 0 | 0 | This attribute displays whether an Path Alarm Indication Signal (P- AIS) alarm state has been entered. An P-AIS alarm state is e… |
| 1.3.6.1.4.1.562.36.2.1.12.14.2.15.1.4 | mscLpSonetPathSignalLabelMismatch | 0 | 0 | This attribute displays whether the Path Signal Label Mismatch (P- SLM) failure condition has been entered. An P-SLM failure cond… |
| 1.3.6.1.4.1.562.36.2.1.12.14.2.15.1.5 | mscLpSonetPathTxAis | 0 | 0 | mscLpSonetPathtxAis |
| 1.3.6.1.4.1.562.36.2.1.12.14.2.15.1.6 | mscLpSonetPathTxRdi | 0 | 0 | mscLpSonetPathtxRdi |