This attribute specifies the type of VC call.
If the value is set to permanentMaster, then a permanent
connection will be established between two ends. The remote end
must be defined as a permanentSlave, permanentBackupSlave, or
permanentSlaveWithBackup. The connection cannot be established
if the remote end is defined as anything else. The end defined as
permanentMaster always initiates the calls. It attempts to call once
per minute.
If the value is set to permanentSlave then a permanent connection
will be established between two ends. The remote end must be
defined as a permanentMaster. The connection cannot be
established if the remote end is defined as anything else. The
permanentSlave end attempts to call once per minute.
If the value is set to permanentSlaveWithBackup then a permanent
connection will be established between the two ends. The remote
end must be defined as a permanentMaster. The connection cannot
be established if the remote interface is defined as anything else.
The permanentSlaveWithBackup attempts to call once per minute.
When type is set to permanentSlaveWithBackup, the connection is
cleared if the interface becomes unavailable. This enables a retry of
the connection which can be redirected to the
permanentBackupSlave.
If the value is set to permanentBackupSlave then a permanent
connection is established between the two ends only if the
permanentMaster end is disconnected from the
permanentSlaveWithBackup end and a backup call is established
by the call redirection system. If the permanentSlaveWithBackup
interface becomes available again, the permanentBackupSlave end
is disconnected and the permanentSlaveWithBackup end is
reconnected to the permanentMaster end. The
permanentBackupSlave end does not try to establish a call.
If the value is set to spvcMaster, then a permanent connection is
established between two ends, with resiliency at the NNI), if the
connection transits across two or more networks. The remote end,
which may be in the same network, or an external network that is
reachable via Frame Relay NNIs, must be defined as either a
spvcSlave, spvcBackupSlave or spvcSlaveWithBackup. The
connection cannot be established if the remote end is defined as
anything else. The end defined as spvcMaster always initiates the
call. It attempts to call once per minute. The call is attempted by the
spvcMaster and accepted by the remote end only if all of the
following conditions are satisfied, at both ends:
1. The physical layer must be operational.
2. The LMI procedures must be in normalCondition (that is, no
service affecting condition).
3. If the LMI side attribute is provisioned to both, the A-bit
received from the interface must be Active. If the LMI side
attribute is not provisioned to both, this condition does not
apply.
After a call is cleared, the spvcMaster end attempts to retry the call
according to the rule for the clear cause. If the call is cleared or
rejected due to the failure of one of the three conditions indicated
above, or due to unavailability of resources along any point in the
connection path, the call will be retried after 60 seconds. For all
other causes, such as loss of service at an NNI, the call will be
retried immediately.
If the value is set to spvcSlave then an SPVC connection is
established between two ends. The remote end must be defined as
an spvcMaster. The connection cannot be established if the remote
end is defined as anything else. The spvcSlave end does not attempt
to call.
If the value is set to spvcSlaveWithBackup then a SPVC connection
is established between the two ends. The remote end must be
defined as an spvcMaster. The connection cannot be established if
the remote interface end is defined as anything else. Unlike a
permanentSlaveWithBackup end, the spvcSlaveWithBackup end
does not attempt to call. If the value is set to spvcSlaveWithBackup,
the connection is cleared if the interface becomes unavailable. This
enables a retry of the connection by the spvcMaster end, which may
be redirected to an end that is set to spvcBackupSlave.
If the value is set to spvcBackupSlave then an SPVC connection is
established between the two ends only if the spvcMaster end is
disconnected from the spvcSlaveWithBackup end, and a backup
call is redirected by the call redirection system. Unlike the PVC
connection, if the spvcSlaveWithBackup interface becomes
available again, the spvcBackupSlave end is not disconnected and
the spvcSlaveWithBackup end is not reconnected to the spvcMaster
end. Neither the spvcBackupSlave nor the spvcSlaveWithBackup
ends try to establish an SPVC call.
Parsed from file nortelPC-frameRelayUniV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-FrameRelayUniMIB
This attribute specifies the type of VC call.
If the value is set to permanentMaster, then a permanent
connection will be established between two ends. The remote end
must be defined as a permanentSlave, permanentBackupSlave, or
permanentSlaveWithBackup. The connection cannot be established
if the remote end is defined as anything else. The end defined as
permanentMaster always initiates the calls. It attempts to call once
per minute.
If the value is set to permanentSlave then a permanent connection
will be established between two ends. The remote end must be
defined as a permanentMaster. The connection cannot be
established if the remote end is defined as anything else. The
permanentSlave end attempts to call once per minute.
If the value is set to permanentSlaveWithBackup then a permanent
connection will be established between the two ends. The remote
end must be defined as a permanentMaster. The connection cannot
be established if the remote interface is defined as anything else.
The permanentSlaveWithBackup attempts to call once per minute.
When type is set to permanentSlaveWithBackup, the connection is
cleared if the interface becomes unavailable. This enables a retry of
the connection which can be redirected to the
permanentBackupSlave.
If the value is set to permanentBackupSlave then a permanent
connection is established between the two ends only if the
permanentMaster end is disconnected from the
permanentSlaveWithBackup end and a backup call is established
by the call redirection system. If the permanentSlaveWithBackup
interface becomes available again, the permanentBackupSlave end
is disconnected and the permanentSlaveWithBackup end is
reconnected to the permanentMaster end. The
permanentBackupSlave end does not try to establish a call.
If the value is set to spvcMaster, then a permanent connection is
established between two ends, with resiliency at the NNI), if the
connection transits across two or more networks. The remote end,
which may be in the same network, or an external network that is
reachable via Frame Relay NNIs, must be defined as either a
spvcSlave, spvcBackupSlave or spvcSlaveWithBackup. The
connection cannot be established if the remote end is defined as
anything else. The end defined as spvcMaster always initiates the
call. It attempts to call once per minute. The call is attempted by the
spvcMaster and accepted by the remote end only if all of the
following conditions are satisfied, at both ends:
1. The physical layer must be operational.
2. The LMI procedures must be in normalCondition (that is, no
service affecting condition).
3. If the LMI side attribute is provisioned to both, the A-bit
received from the interface must be Active. If the LMI side
attribute is not provisioned to both, this condition does not
apply.
After a call is cleared, the spvcMaster end attempts to retry the call
according to the rule for the clear cause. If the call is cleared or
rejected due to the failure of one of the three conditions indicated
above, or due to unavailability of resources along any point in the
connection path, the call will be retried after 60 seconds. For all
other causes, such as loss of service at an NNI, the call will be
retried immediately.
If the value is set to spvcSlave then an SPVC connection is
established between two ends. The remote end must be defined as
an spvcMaster. The connection cannot be established if the remote
end is defined as anything else. The spvcSlave end does not attempt
to call.
If the value is set to spvcSlaveWithBackup then a SPVC connection
is established between the two ends. The remote end must be
defined as an spvcMaster. The connection cannot be established if
the remote interface end is defined as anything else. Unlike a
permanentSlaveWithBackup end, the spvcSlaveWithBackup end
does not attempt to call. If the value is set to spvcSlaveWithBackup,
the connection is cleared if the interface becomes unavailable. This
enables a retry of the connection by the spvcMaster end, which may
be redirected to an end that is set to spvcBackupSlave.
If the value is set to spvcBackupSlave then an SPVC connection is
established between the two ends only if the spvcMaster end is
disconnected from the spvcSlaveWithBackup end, and a backup
call is redirected by the call redirection system. Unlike the PVC
connection, if the spvcSlaveWithBackup interface becomes
available again, the spvcBackupSlave end is not disconnected and
the spvcSlaveWithBackup end is not reconnected to the spvcMaster
end. Neither the spvcBackupSlave nor the spvcSlaveWithBackup
ends try to establish an SPVC call.
Parsed from file Nortel-MsCarrier-MscPassport-FrameRelayUniMIB.mib
Module: Nortel-MsCarrier-MscPassport-FrameRelayUniMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-FrameRelayUniMIB
[Automatically extracted from oidview.com]
mscFrUniDlciDcType OBJECT-TYPE SYNTAX INTEGER { permanentMaster(1), permanentSlave(2), permanentBackupSlave(3), permanentSlaveWithBackup(4), spvcMaster(5), spvcSlave(6), spvcBackupSlave(7), spvcSlaveWithBackup(8) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of VC call. If the value is set to permanentMaster, then a permanent connection will be established between two ends. The remote end must be defined as a permanentSlave, permanentBackupSlave, or permanentSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It attempts to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote end is defined as anything else. The permanentSlave end attempts to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote interface is defined as anything else. The permanentSlaveWithBackup attempts to call once per minute. When type is set to permanentSlaveWithBackup, the connection is cleared if the interface becomes unavailable. This enables a retry of the connection which can be redirected to the permanentBackupSlave. If the value is set to permanentBackupSlave then a permanent connection is established between the two ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the call redirection system. If the permanentSlaveWithBackup interface becomes available again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish a call. If the value is set to spvcMaster, then a permanent connection is established between two ends, with resiliency at the NNI), if the connection transits across two or more networks. The remote end, which may be in the same network, or an external network that is reachable via Frame Relay NNIs, must be defined as either a spvcSlave, spvcBackupSlave or spvcSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as spvcMaster always initiates the call. It attempts to call once per minute. The call is attempted by the spvcMaster and accepted by the remote end only if all of the following conditions are satisfied, at both ends: 1. The physical layer must be operational. 2. The LMI procedures must be in normalCondition (that is, no service affecting condition). 3. If the LMI side attribute is provisioned to both, the A-bit received from the interface must be Active. If the LMI side attribute is not provisioned to both, this condition does not apply. After a call is cleared, the spvcMaster end attempts to retry the call according to the rule for the clear cause. If the call is cleared or rejected due to the failure of one of the three conditions indicated above, or due to unavailability of resources along any point in the connection path, the call will be retried after 60 seconds. For all other causes, such as loss of service at an NNI, the call will be retried immediately. If the value is set to spvcSlave then an SPVC connection is established between two ends. The remote end must be defined as an spvcMaster. The connection cannot be established if the remote end is defined as anything else. The spvcSlave end does not attempt to call. If the value is set to spvcSlaveWithBackup then a SPVC connection is established between the two ends. The remote end must be defined as an spvcMaster. The connection cannot be established if the remote interface end is defined as anything else. Unlike a permanentSlaveWithBackup end, the spvcSlaveWithBackup end does not attempt to call. If the value is set to spvcSlaveWithBackup, the connection is cleared if the interface becomes unavailable. This enables a retry of the connection by the spvcMaster end, which may be redirected to an end that is set to spvcBackupSlave. If the value is set to spvcBackupSlave then an SPVC connection is established between the two ends only if the spvcMaster end is disconnected from the spvcSlaveWithBackup end, and a backup call is redirected by the call redirection system. Unlike the PVC connection, if the spvcSlaveWithBackup interface becomes available again, the spvcBackupSlave end is not disconnected and the spvcSlaveWithBackup end is not reconnected to the spvcMaster end. Neither the spvcBackupSlave nor the spvcSlaveWithBackup ends try to establish an SPVC call." DEFVAL { permanentMaster } ::= { mscFrUniDlciDcOptionsEntry 6 }
mscFrUniDlciDcType OBJECT-TYPE SYNTAX INTEGER { permanentMaster(1), permanentSlave(2), permanentBackupSlave(3), permanentSlaveWithBackup(4), spvcMaster(5), spvcSlave(6), spvcBackupSlave(7), spvcSlaveWithBackup(8) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of VC call. If the value is set to permanentMaster, then a permanent connection will be established between two ends. The remote end must be defined as a permanentSlave, permanentBackupSlave, or permanentSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It attempts to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote end is defined as anything else. The permanentSlave end attempts to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote interface is defined as anything else. The permanentSlaveWithBackup attempts to call once per minute. When type is set to permanentSlaveWithBackup, the connection is cleared if the interface becomes unavailable. This enables a retry of the connection which can be redirected to the permanentBackupSlave. If the value is set to permanentBackupSlave then a permanent connection is established between the two ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the call redirection system. If the permanentSlaveWithBackup interface becomes available again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish a call. If the value is set to spvcMaster, then a permanent connection is established between two ends, with resiliency at the NNI), if the connection transits across two or more networks. The remote end, which may be in the same network, or an external network that is reachable via Frame Relay NNIs, must be defined as either a spvcSlave, spvcBackupSlave or spvcSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as spvcMaster always initiates the call. It attempts to call once per minute. The call is attempted by the spvcMaster and accepted by the remote end only if all of the following conditions are satisfied, at both ends: 1. The physical layer must be operational. 2. The LMI procedures must be in normalCondition (that is, no service affecting condition). 3. If the LMI side attribute is provisioned to both, the A-bit received from the interface must be Active. If the LMI side attribute is not provisioned to both, this condition does not apply. After a call is cleared, the spvcMaster end attempts to retry the call according to the rule for the clear cause. If the call is cleared or rejected due to the failure of one of the three conditions indicated above, or due to unavailability of resources along any point in the connection path, the call will be retried after 60 seconds. For all other causes, such as loss of service at an NNI, the call will be retried immediately. If the value is set to spvcSlave then an SPVC connection is established between two ends. The remote end must be defined as an spvcMaster. The connection cannot be established if the remote end is defined as anything else. The spvcSlave end does not attempt to call. If the value is set to spvcSlaveWithBackup then a SPVC connection is established between the two ends. The remote end must be defined as an spvcMaster. The connection cannot be established if the remote interface end is defined as anything else. Unlike a permanentSlaveWithBackup end, the spvcSlaveWithBackup end does not attempt to call. If the value is set to spvcSlaveWithBackup, the connection is cleared if the interface becomes unavailable. This enables a retry of the connection by the spvcMaster end, which may be redirected to an end that is set to spvcBackupSlave. If the value is set to spvcBackupSlave then an SPVC connection is established between the two ends only if the spvcMaster end is disconnected from the spvcSlaveWithBackup end, and a backup call is redirected by the call redirection system. Unlike the PVC connection, if the spvcSlaveWithBackup interface becomes available again, the spvcBackupSlave end is not disconnected and the spvcSlaveWithBackup end is not reconnected to the spvcMaster end. Neither the spvcBackupSlave nor the spvcSlaveWithBackup ends try to establish an SPVC call." DEFVAL { permanentMaster } ::= { mscFrUniDlciDcOptionsEntry 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.3 | mscFrUniDlciDcRemoteNpi | 0 | 0 | This attribute specifies the Numbering Plan Indicator (NPI) of the remoteDna. |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.4 | mscFrUniDlciDcRemoteDna | 0 | 0 | This attribute specifies the Data Network Address (DNA) of the service at the remote end of the DLCI. This is the called (destina… |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.5 | mscFrUniDlciDcRemoteDlci | 0 | 0 | This attribute specifies the remote DLCI of the PVC connection. |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.9 | mscFrUniDlciDcTransferPriority | 0 | 0 | This attribute specifies the transfer priority to the local network for the outgoing calls using this particular DLCI. It overri… |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.10 | mscFrUniDlciDcDiscardPriority | 0 | 0 | This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning val… |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.11 | mscFrUniDlciDcDeDiscardPriority | 0 | 0 | This attribute specifies whether the discardPriority applies to DE frames for this DLCI. When set to determinedByDiscardPriority… |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.12 | mscFrUniDlciDcDataPath | 0 | 0 | This attribute specifies the data path to be used by Virtual Circuits on this interface. The value of the dataPath attribute in … |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.13 | mscFrUniDlciDcCugIndex | 0 | 0 | This attribute specifies the CUG index which is to be signalled in PVC and SPVC call requests to the remote end. The type of CUG… |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.14 | mscFrUniDlciDcCugType | 0 | 0 | This attribute specifies the type of CUG signalling to be used in PVC and SPVC call requests. Index of CUG to be used is defined… |
| 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.15 | mscFrUniDlciDcMapIpCosToFrQos | 0 | 0 | This attribute specifies whether an IP TOS value is mapped to an FR QOS. The mapping used is provisioned in the Mod Frs IpCosToFr… |