The number of times this interface has detected the loss of signal
condition from the ring.
Parsed from file TNI-MIB.mib
Module: TNI-MIB
Vendor: Transition Engineering Inc.
Module: TNI-MIB
[Automatically extracted from oidview.com]
tnTRV1StatsSignalLoss OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times this interface has detected the loss of signal condition from the ring." ::= { tnTRVer1 20 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.2.1.2.1 | tnTRV1Commands | 0 | 0 | When this object is set to the value of open(2), the station should go into the open state. The progress and success of the ope… |
| 1.3.6.1.4.1.868.2.2.1.2.2 | tnTRV1RingStatus | 0 | 0 | The current interface status which can be used to diagnose fluctuating problems that can occur on token rings, after a station ha… |
| 1.3.6.1.4.1.868.2.2.1.2.3 | tnTRV1RingState | 0 | 0 | The current interface state with respect to entering or leaving the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.4 | tnTRV1RingOpenStatus | 0 | 0 | This object indicates the success, or the reason for failure, of the station's most recent attempt to enter the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.5 | tnTRV1RingSpeed | 0 | 0 | The ring's bandwidth. |
| 1.3.6.1.4.1.868.2.2.1.2.6 | tnTRV1UpStream | 0 | 0 | The MAC-address of the up stream neighbor station in the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.7 | tnTRV1ActMonParticipate | 0 | 0 | If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the valu… |
| 1.3.6.1.4.1.868.2.2.1.2.8 | tnTRV1Functional | 0 | 0 | The bit mask of all Token Ring functional addresses for which this interface will accept frames. |
| 1.3.6.1.4.1.868.2.2.1.2.9 | tnTRV1StatsLineErrors | 0 | 0 | This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token an… |
| 1.3.6.1.4.1.868.2.2.1.2.10 | tnTRV1StatsBurstErrors | 0 | 0 | This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error). |
| 1.3.6.1.4.1.868.2.2.1.2.11 | tnTRV1StatsACErrors | 0 | 0 | This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receive… |
| 1.3.6.1.4.1.868.2.2.1.2.12 | tnTRV1StatsAbortTransErrors | 0 | 0 | This counter is incremented when a station transmits an abort delimiter while transmitting. |
| 1.3.6.1.4.1.868.2.2.1.2.13 | tnTRV1StatsInternalErrors | 0 | 0 | This counter is incremented when a station recognizes an internal error. |
| 1.3.6.1.4.1.868.2.2.1.2.14 | tnTRV1StatsLostFrameErrors | 0 | 0 | This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where … |
| 1.3.6.1.4.1.868.2.2.1.2.15 | tnTRV1StatsReceiveCongestions | 0 | 0 | This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer spa… |
| 1.3.6.1.4.1.868.2.2.1.2.16 | tnTRV1StatsFrameCopiedErrors | 0 | 0 | This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A b… |
| 1.3.6.1.4.1.868.2.2.1.2.17 | tnTRV1StatsTokenErrors | 0 | 0 | This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmit… |
| 1.3.6.1.4.1.868.2.2.1.2.18 | tnTRV1StatsSoftErrors | 0 | 0 | The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this… |
| 1.3.6.1.4.1.868.2.2.1.2.19 | tnTRV1StatsHardErrors | 0 | 0 | The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this inte… |
| 1.3.6.1.4.1.868.2.2.1.2.21 | tnTRV1StatsTransmitBeacons | 0 | 0 | The number of times this interface has transmitted a beacon frame. |
| 1.3.6.1.4.1.868.2.2.1.2.22 | tnTRV1StatsRecoverys | 0 | 0 | The number of Claim Token MAC frames received or transmitted after the interface has received a Ring Purge MAC frame. This coun… |
| 1.3.6.1.4.1.868.2.2.1.2.23 | tnTRV1StatsLobeWires | 0 | 0 | The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed and do… |
| 1.3.6.1.4.1.868.2.2.1.2.24 | tnTRV1StatsRemoves | 0 | 0 | The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interfa… |
| 1.3.6.1.4.1.868.2.2.1.2.25 | tnTRV1StatsSingles | 0 | 0 | The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the … |
| 1.3.6.1.4.1.868.2.2.1.2.26 | tnTRV1StatsFreqErrors | 0 | 0 | The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency by … |
| 1.3.6.1.4.1.868.2.2.1.2.27 | tnTRV1TimerReturnRepeat | 0 | 0 | The time-out value used to ensure the interface will return to Repeat State, in units of 100 micro-seconds. The value should be… |
| 1.3.6.1.4.1.868.2.2.1.2.28 | tnTRV1TimerHolding | 0 | 0 | Maximum period of time a station is permitted to transmit frames after capturing a token, in units of 100 micro-seconds. Implemen… |
| 1.3.6.1.4.1.868.2.2.1.2.29 | tnTRV1TimerQueuePDU | 0 | 0 | The time-out value for enqueuing of an SMP PDU after reception of an AMP or SMP frame in which the A and C bits were equal to 0,… |
| 1.3.6.1.4.1.868.2.2.1.2.30 | tnTRV1TimerValidTransmit | 0 | 0 | The time-out value used by the active monitor to detect the absence of valid transmissions, in units of 100 micro-seconds. Impl… |
| 1.3.6.1.4.1.868.2.2.1.2.31 | tnTRV1TimerNoToken | 0 | 0 | The time-out value used to recover from various-related error situations [9]. If N is the maximum number of stations on the rin… |
| 1.3.6.1.4.1.868.2.2.1.2.32 | tnTRV1TimerActiveMon | 0 | 0 | The time-out value used by the active monitor to stimulate the enqueuing of an AMP PDU for transmission, in units of 100 micro-se… |
| 1.3.6.1.4.1.868.2.2.1.2.33 | tnTRV1TimerStandbyMon | 0 | 0 | The time-out value used by the stand-by monitors to ensure that there is an active monitor on the ring and to detect a continuou… |
| 1.3.6.1.4.1.868.2.2.1.2.34 | tnTRV1TimerErrorReport | 0 | 0 | The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in uni… |
| 1.3.6.1.4.1.868.2.2.1.2.35 | tnTRV1TimerBeaconTransmit | 0 | 0 | The time-out value which determines how long a station shall remain in the state of transmitting Beacon frames before entering t… |
| 1.3.6.1.4.1.868.2.2.1.2.36 | tnTRV1TimerBeaconReceive | 0 | 0 | The time-out value which determines how long a station shall receive Beacon frames from its downstream neighbor before entering … |