The number of times the interface has sensed that it is the only
station on the ring. This will happen if the interface is the first
one up on a ring, or if there is a hardware problem.
Parsed from file TNI-MIB.mib
Module: TNI-MIB
Vendor: Transition Engineering Inc.
Module: TNI-MIB
[Automatically extracted from oidview.com]
tnTRV1StatsSingles OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the first one up on a ring, or if there is a hardware problem." ::= { tnTRVer1 25 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.2.1.2.1 | tnTRV1Commands | 0 | 0 | When this object is set to the value of open(2), the station should go into the open state. The progress and success of the ope… |
| 1.3.6.1.4.1.868.2.2.1.2.2 | tnTRV1RingStatus | 0 | 0 | The current interface status which can be used to diagnose fluctuating problems that can occur on token rings, after a station ha… |
| 1.3.6.1.4.1.868.2.2.1.2.3 | tnTRV1RingState | 0 | 0 | The current interface state with respect to entering or leaving the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.4 | tnTRV1RingOpenStatus | 0 | 0 | This object indicates the success, or the reason for failure, of the station's most recent attempt to enter the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.5 | tnTRV1RingSpeed | 0 | 0 | The ring's bandwidth. |
| 1.3.6.1.4.1.868.2.2.1.2.6 | tnTRV1UpStream | 0 | 0 | The MAC-address of the up stream neighbor station in the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.7 | tnTRV1ActMonParticipate | 0 | 0 | If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the valu… |
| 1.3.6.1.4.1.868.2.2.1.2.8 | tnTRV1Functional | 0 | 0 | The bit mask of all Token Ring functional addresses for which this interface will accept frames. |
| 1.3.6.1.4.1.868.2.2.1.2.9 | tnTRV1StatsLineErrors | 0 | 0 | This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token an… |
| 1.3.6.1.4.1.868.2.2.1.2.10 | tnTRV1StatsBurstErrors | 0 | 0 | This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error). |
| 1.3.6.1.4.1.868.2.2.1.2.11 | tnTRV1StatsACErrors | 0 | 0 | This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receive… |
| 1.3.6.1.4.1.868.2.2.1.2.12 | tnTRV1StatsAbortTransErrors | 0 | 0 | This counter is incremented when a station transmits an abort delimiter while transmitting. |
| 1.3.6.1.4.1.868.2.2.1.2.13 | tnTRV1StatsInternalErrors | 0 | 0 | This counter is incremented when a station recognizes an internal error. |
| 1.3.6.1.4.1.868.2.2.1.2.14 | tnTRV1StatsLostFrameErrors | 0 | 0 | This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where … |
| 1.3.6.1.4.1.868.2.2.1.2.15 | tnTRV1StatsReceiveCongestions | 0 | 0 | This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer spa… |
| 1.3.6.1.4.1.868.2.2.1.2.16 | tnTRV1StatsFrameCopiedErrors | 0 | 0 | This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A b… |
| 1.3.6.1.4.1.868.2.2.1.2.17 | tnTRV1StatsTokenErrors | 0 | 0 | This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmit… |
| 1.3.6.1.4.1.868.2.2.1.2.18 | tnTRV1StatsSoftErrors | 0 | 0 | The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this… |
| 1.3.6.1.4.1.868.2.2.1.2.19 | tnTRV1StatsHardErrors | 0 | 0 | The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this inte… |
| 1.3.6.1.4.1.868.2.2.1.2.20 | tnTRV1StatsSignalLoss | 0 | 0 | The number of times this interface has detected the loss of signal condition from the ring. |
| 1.3.6.1.4.1.868.2.2.1.2.21 | tnTRV1StatsTransmitBeacons | 0 | 0 | The number of times this interface has transmitted a beacon frame. |
| 1.3.6.1.4.1.868.2.2.1.2.22 | tnTRV1StatsRecoverys | 0 | 0 | The number of Claim Token MAC frames received or transmitted after the interface has received a Ring Purge MAC frame. This coun… |
| 1.3.6.1.4.1.868.2.2.1.2.23 | tnTRV1StatsLobeWires | 0 | 0 | The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed and do… |
| 1.3.6.1.4.1.868.2.2.1.2.24 | tnTRV1StatsRemoves | 0 | 0 | The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interfa… |
| 1.3.6.1.4.1.868.2.2.1.2.26 | tnTRV1StatsFreqErrors | 0 | 0 | The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency by … |
| 1.3.6.1.4.1.868.2.2.1.2.27 | tnTRV1TimerReturnRepeat | 0 | 0 | The time-out value used to ensure the interface will return to Repeat State, in units of 100 micro-seconds. The value should be… |
| 1.3.6.1.4.1.868.2.2.1.2.28 | tnTRV1TimerHolding | 0 | 0 | Maximum period of time a station is permitted to transmit frames after capturing a token, in units of 100 micro-seconds. Implemen… |
| 1.3.6.1.4.1.868.2.2.1.2.29 | tnTRV1TimerQueuePDU | 0 | 0 | The time-out value for enqueuing of an SMP PDU after reception of an AMP or SMP frame in which the A and C bits were equal to 0,… |
| 1.3.6.1.4.1.868.2.2.1.2.30 | tnTRV1TimerValidTransmit | 0 | 0 | The time-out value used by the active monitor to detect the absence of valid transmissions, in units of 100 micro-seconds. Impl… |
| 1.3.6.1.4.1.868.2.2.1.2.31 | tnTRV1TimerNoToken | 0 | 0 | The time-out value used to recover from various-related error situations [9]. If N is the maximum number of stations on the rin… |
| 1.3.6.1.4.1.868.2.2.1.2.32 | tnTRV1TimerActiveMon | 0 | 0 | The time-out value used by the active monitor to stimulate the enqueuing of an AMP PDU for transmission, in units of 100 micro-se… |
| 1.3.6.1.4.1.868.2.2.1.2.33 | tnTRV1TimerStandbyMon | 0 | 0 | The time-out value used by the stand-by monitors to ensure that there is an active monitor on the ring and to detect a continuou… |
| 1.3.6.1.4.1.868.2.2.1.2.34 | tnTRV1TimerErrorReport | 0 | 0 | The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in uni… |
| 1.3.6.1.4.1.868.2.2.1.2.35 | tnTRV1TimerBeaconTransmit | 0 | 0 | The time-out value which determines how long a station shall remain in the state of transmitting Beacon frames before entering t… |
| 1.3.6.1.4.1.868.2.2.1.2.36 | tnTRV1TimerBeaconReceive | 0 | 0 | The time-out value which determines how long a station shall receive Beacon frames from its downstream neighbor before entering … |