This object specifies the desired line rate which the STU-C
will attempt to train at.
This object specifies the desired line rate which the STU-C
will attempt to train at.
Parsed from file CISCO-SDSL-LINE-MIB.my.txt
Company: None
Module: CISCO-SDSL-LINE-MIB
This object specifies the desired line rate which the STU-C
will attempt to train at.
cSdslLineMaxRate OBJECT-TYPE SYNTAX INTEGER(144000|272000|400000|528000|784000|1040000|1168000|1552000|2064000|2320000) ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the desired line rate which the STU-C will attempt to train at." DEFVAL { 784000 } ::= { cSdslLineConfProfileEntry 1 }
Vendor: Cisco
Module: CISCO-SDSL-LINE-MIB
[Automatically extracted from oidview.com]
cSdslLineMaxRate OBJECT-TYPE SYNTAX Integer32 (144000 | 272000 | 400000 | 528000 | 784000 | 1040000 | 1168000 | 1552000 | 2064000 | 2320000 ) UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the desired line rate which the STU-C will attempt to train at." DEFVAL { 784000 } ::= { cSdslLineConfProfileEntry 1 }
cSdslLineMaxRate OBJECT-TYPE SYNTAX Integer32 (144000 | 272000 | 400000 | 528000 | 784000 | 1040000 | 1168000 | 1552000 | 2064000 | 2320000 ) UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the desired line rate which the STU-C will attempt to train at." DEFVAL { 784000 } ::= { cSdslLineConfProfileEntry 1 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.9.9.155.1.14.1.2 | cSdslLineFramingMode | 0 | 0 | This object specifies the desired Transmission Convergence framing structure being used by the interface. |
1.3.6.1.4.1.9.9.155.1.14.1.3 | cSdslStucTargetSnrMgn | 0 | 0 | This object specifies the target SNR margin. This is the desired noise margin the STU-C must achieve with a BER of 10-7 or bette… |
1.3.6.1.4.1.9.9.155.1.14.1.4 | cSdslStucMaxSnrMgn | 0 | 0 | This object specifies the maximum acceptable SNR margin. If the noise margin exceeds this level, then the STU-C should attempt to… |
1.3.6.1.4.1.9.9.155.1.14.1.5 | cSdslStucMinSnrMgn | 0 | 0 | This object specifies the minimum acceptable SNR margin. If the noise margin falls below this level, the STU-C will retrain. The … |
1.3.6.1.4.1.9.9.155.1.14.1.6 | cSdslStucOutputPwr | 0 | 0 | This object specifies the transmit power level used by the STU-C. The value for this object must be in multiples of 10. The speci… |
1.3.6.1.4.1.9.9.155.1.14.1.7 | cSdslShdslLineMaxRate | 0 | 0 | This object specifies the desired line rate at which the G.shdsl STU-C will attempt to train. |
1.3.6.1.4.1.9.9.155.1.14.1.8 | cSdslStucPsdMaskType | 0 | 0 | This object specifies the PSD mask type for the transceiver. For all values of the cSdslShdslLineMaxRate, the symmetric PSD maskt… |
1.3.6.1.4.1.9.9.155.1.14.1.9 | cSdslStucAnnex | 0 | 0 | This object specifies the operating conditions for the port of G.shdsl CO equipment . Annex A is optimized for conditions typical… |
1.3.6.1.4.1.9.9.155.1.14.1.10 | cSdslLineEquipmentType | 0 | 0 | This object specifies the type of the STU device ,either STU-C or STU-R |
1.3.6.1.4.1.9.9.155.1.14.1.11 | cSdslLineAutoRateEnable | 0 | 0 | This object specifies whether the device uses the rate adaptive training mode. |
1.3.6.1.4.1.9.9.155.1.14.1.12 | cSdslStucThresholdSnrMgn | 0 | 0 | This object specifies the SNR margin threshold. An appropriate alarm should be generated when the difference between the actual … |
1.3.6.1.4.1.9.9.155.1.14.1.13 | cSdslSturAnnex | 0 | 0 | This object specifies the operating conditions for the port of G.shdsl CPE equipment. Annex A is optimized for conditions typical… |