This MIB module describes all variations of the symmetric
DSL line interfaces. The structure of this module resembles
and maintains consistency with the ADSL-LINE-MIB,
ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, and
CISCO-ADSL-CAP-LINE-MIB. Observe that the tables in this
module do not necessarily extend the tables defined by the
these mibs. Currently, only those tables that contain
configuration information extend the profile tables defined
by the above modules. This allows the management
client to define DSL configuration profiles that apply across
all DSL modems, independent of the technology being utilized by
the modem.
*** DEFINITIONS ***
ATTENUATION
Attenuation is a decrease in the strength of a signal
over the length of a cable.
CODING VIOLATION
A coding violation occurs when the incoming signal exhibits
a CRC anomaly.
DOWNSTREAM
The flow of data in the direction from the ATU-C to ATU-R.
ERRORED SECOND
A second with one or more coding violations or one or more
incoming defects (e.g., LOS or LOSQ).
LINE RATE
The total data rate supported by a line. Observe that the
payload rate is equal the line rate for the earliest
implementations of SDSL. However, the payload rate maybe
less than the line rate for future implementations.
LOSS OF SYNC DEFECT
A Loss of Sync Defect is defined as 3 consecutive received
frames which contain one or more errors in the framing
bits. A Loss of Sync Defect shall be cleared when at least
2 consecutive received frames contain no errors in the
framing bits.
LOSS OF SYNC FAILURE
A LOSW Failure is defined as at least 2 consecutive
seconds of LOSW Defect. The LOSW Failure should be
cleared when the LOSW defect is absent for 20 seconds or
less. (i.e. clear within 20 seconds ).
MARGIN (also referred to as 'SNR margin')
The difference between the SNR of the received signal and
the SNR required to provide a BER of 10E-7.
SEVERELY ERRORED SECOND
A one second interval during which or more LOSW or CV defects
are declared.
UNAVAILABLE SECOND
A Unavailable Second is defined as a one second interval
during which LOSW Failure ( at least 2 seconds of LOSW
Defect ).
UPSTREAM
The flow of data in the direction from the ATU-R to ATU-C.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
ADSL - Asymmetric Digital Subscriber Line.
ATM - Asynchronous Transfer Mode.
BER - Bit Error Ratio.
CV - Coding Violation.
DSL - Digital Subscriber Line.
ES - Errored Second.
LOS - Loss Of Sync.
LOSQ - Loss Of Signal Quality.
LOSW - Loss of Sync Word Failure
PSD - Power Spectral Density.
SES - Severely Errored Second.
SNR - Signal-to-Noise Ratio.
STM - Synchronous Transfer Mode.
STU-C - SDSL Transceiver Unit, Central Office end.
STU-R - ADSL Transceiver Unit, Remote terminal end.
UAS - UnAvailable Second.
Parsed from file CISCO-SDSL-LINE-MIB.my.txt
Company: None
Module: CISCO-SDSL-LINE-MIB
This MIB module describes all variations of the symmetric
DSL line interfaces. The structure of this module resembles
and maintains consistency with the ADSL-LINE-MIB,
ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, and
CISCO-ADSL-CAP-LINE-MIB. Observe that the tables in this
module do not necessarily extend the tables defined by the
these mibs. Currently, only those tables that contain
configuration information extend the profile tables defined
by the above modules. This allows the management
client to define DSL configuration profiles that apply across
all DSL modems, independent of the technology being utilized by
the modem.
*** DEFINITIONS ***
ATTENUATION
Attenuation is a decrease in the strength of a signal
over the length of a cable.
CODING VIOLATION
A coding violation occurs when the incoming signal exhibits
a CRC anomaly.
DOWNSTREAM
The flow of data in the direction from the ATU-C to ATU-R.
ERRORED SECOND
A second with one or more coding violations or one or more
incoming defects (e.g., LOS or LOSQ).
LINE RATE
The total data rate supported by a line. Observe that the
payload rate is equal the line rate for the earliest
implementations of SDSL. However, the payload rate maybe
less than the line rate for future implementations.
LOSS OF SYNC DEFECT
A Loss of Sync Defect is defined as 3 consecutive received
frames which contain one or more errors in the framing
bits. A Loss of Sync Defect shall be cleared when at least
2 consecutive received frames contain no errors in the
framing bits.
LOSS OF SYNC FAILURE
A LOSW Failure is defined as at least 2 consecutive
seconds of LOSW Defect. The LOSW Failure should be
cleared when the LOSW defect is absent for 20 seconds or
less. (i.e. clear within 20 seconds ).
MARGIN (also referred to as 'SNR margin')
The difference between the SNR of the received signal and
the SNR required to provide a BER of 10E-7.
SEVERELY ERRORED SECOND
A one second interval during which or more LOSW or CV defects
are declared.
UNAVAILABLE SECOND
A Unavailable Second is defined as a one second interval
during which LOSW Failure ( at least 2 seconds of LOSW
Defect ).
UPSTREAM
The flow of data in the direction from the ATU-R to ATU-C.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
ADSL - Asymmetric Digital Subscriber Line.
ATM - Asynchronous Transfer Mode.
BER - Bit Error Ratio.
CV - Coding Violation.
DSL - Digital Subscriber Line.
ES - Errored Second.
LOS - Loss Of Sync.
LOSQ - Loss Of Signal Quality.
LOSW - Loss of Sync Word Failure
PSD - Power Spectral Density.
SES - Severely Errored Second.
SNR - Signal-to-Noise Ratio.
STM - Synchronous Transfer Mode.
STU-C - SDSL Transceiver Unit, Central Office end.
STU-R - ADSL Transceiver Unit, Remote terminal end.
UAS - UnAvailable Second.
ciscoSdslLineMIB OBJECT IDENTIFIER ::= { ciscoMgmt 155 }
Vendor: Cisco
Module: CISCO-SDSL-LINE-MIB
[Automatically extracted from oidview.com]
ciscoSdslLineMIB MODULE-IDENTITY LAST-UPDATED "200108201000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "This MIB module describes all variations of the symmetric DSL line interfaces. The structure of this module resembles and maintains consistency with the ADSL-LINE-MIB, ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, and CISCO-ADSL-CAP-LINE-MIB. Observe that the tables in this module do not necessarily extend the tables defined by the these mibs. Currently, only those tables that contain configuration information extend the profile tables defined by the above modules. This allows the management client to define DSL configuration profiles that apply across all DSL modems, independent of the technology being utilized by the modem. *** DEFINITIONS *** ATTENUATION Attenuation is a decrease in the strength of a signal over the length of a cable. CODING VIOLATION A coding violation occurs when the incoming signal exhibits a CRC anomaly. DOWNSTREAM The flow of data in the direction from the ATU-C to ATU-R. ERRORED SECOND A second with one or more coding violations or one or more incoming defects (e.g., LOS or LOSQ). LINE RATE The total data rate supported by a line. Observe that the payload rate is equal the line rate for the earliest implementations of SDSL. However, the payload rate maybe less than the line rate for future implementations. LOSS OF SYNC DEFECT A Loss of Sync Defect is defined as 3 consecutive received frames which contain one or more errors in the framing bits. A Loss of Sync Defect shall be cleared when at least 2 consecutive received frames contain no errors in the framing bits. LOSS OF SYNC FAILURE A LOSW Failure is defined as at least 2 consecutive seconds of LOSW Defect. The LOSW Failure should be cleared when the LOSW defect is absent for 20 seconds or less. (i.e. clear within 20 seconds ). MARGIN (also referred to as 'SNR margin') The difference between the SNR of the received signal and the SNR required to provide a BER of 10E-7. SEVERELY ERRORED SECOND A one second interval during which or more LOSW or CV defects are declared. UNAVAILABLE SECOND A Unavailable Second is defined as a one second interval during which LOSW Failure ( at least 2 seconds of LOSW Defect ). UPSTREAM The flow of data in the direction from the ATU-R to ATU-C. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** ADSL - Asymmetric Digital Subscriber Line. ATM - Asynchronous Transfer Mode. BER - Bit Error Ratio. CV - Coding Violation. DSL - Digital Subscriber Line. ES - Errored Second. LOS - Loss Of Sync. LOSQ - Loss Of Signal Quality. LOSW - Loss of Sync Word Failure PSD - Power Spectral Density. SES - Severely Errored Second. SNR - Signal-to-Noise Ratio. STM - Synchronous Transfer Mode. STU-C - SDSL Transceiver Unit, Central Office end. STU-R - ADSL Transceiver Unit, Remote terminal end. UAS - UnAvailable Second." REVISION "200108201000Z" DESCRIPTION "The object cSdslStucCurrGain and cSdslSturCurrGain are deprecated to remove the range. The new objects added are cSdslStucCurrGainRev and cSdslSturCurrGainRev." REVISION "200104091013Z" DESCRIPTION "Added cSdslSturAnnex for G.shdsl CPE device. Also updated description for cSdslStucAnnex. " REVISION "200101301600Z" DESCRIPTION "Added cSdslLineEquipmentType, cSdslLineAutoRateEnable. cSdslShdslLineMaxRate, cSdslStucPsdMaskType, cSdslStucAnnex, and cSdslStucThresholdSnrMgn. Changed default for cSdslLineMaxRate. Updated description for SNR and output pwr profile settings." ::= { ciscoMgmt 155 }
ciscoSdslLineMIB MODULE-IDENTITY LAST-UPDATED "200108201000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "This MIB module describes all variations of the symmetric DSL line interfaces. The structure of this module resembles and maintains consistency with the ADSL-LINE-MIB, ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, and CISCO-ADSL-CAP-LINE-MIB. Observe that the tables in this module do not necessarily extend the tables defined by the these mibs. Currently, only those tables that contain configuration information extend the profile tables defined by the above modules. This allows the management client to define DSL configuration profiles that apply across all DSL modems, independent of the technology being utilized by the modem. *** DEFINITIONS *** ATTENUATION Attenuation is a decrease in the strength of a signal over the length of a cable. CODING VIOLATION A coding violation occurs when the incoming signal exhibits a CRC anomaly. DOWNSTREAM The flow of data in the direction from the ATU-C to ATU-R. ERRORED SECOND A second with one or more coding violations or one or more incoming defects (e.g., LOS or LOSQ). LINE RATE The total data rate supported by a line. Observe that the payload rate is equal the line rate for the earliest implementations of SDSL. However, the payload rate maybe less than the line rate for future implementations. LOSS OF SYNC DEFECT A Loss of Sync Defect is defined as 3 consecutive received frames which contain one or more errors in the framing bits. A Loss of Sync Defect shall be cleared when at least 2 consecutive received frames contain no errors in the framing bits. LOSS OF SYNC FAILURE A LOSW Failure is defined as at least 2 consecutive seconds of LOSW Defect. The LOSW Failure should be cleared when the LOSW defect is absent for 20 seconds or less. (i.e. clear within 20 seconds ). MARGIN (also referred to as 'SNR margin') The difference between the SNR of the received signal and the SNR required to provide a BER of 10E-7. SEVERELY ERRORED SECOND A one second interval during which or more LOSW or CV defects are declared. UNAVAILABLE SECOND A Unavailable Second is defined as a one second interval during which LOSW Failure ( at least 2 seconds of LOSW Defect ). UPSTREAM The flow of data in the direction from the ATU-R to ATU-C. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** ADSL - Asymmetric Digital Subscriber Line. ATM - Asynchronous Transfer Mode. BER - Bit Error Ratio. CV - Coding Violation. DSL - Digital Subscriber Line. ES - Errored Second. LOS - Loss Of Sync. LOSQ - Loss Of Signal Quality. LOSW - Loss of Sync Word Failure PSD - Power Spectral Density. SES - Severely Errored Second. SNR - Signal-to-Noise Ratio. STM - Synchronous Transfer Mode. STU-C - SDSL Transceiver Unit, Central Office end. STU-R - ADSL Transceiver Unit, Remote terminal end. UAS - UnAvailable Second." REVISION "200108201000Z" DESCRIPTION "The object cSdslStucCurrGain and cSdslSturCurrGain are deprecated to remove the range. The new objects added are cSdslStucCurrGainRev and cSdslSturCurrGainRev." REVISION "200104091013Z" DESCRIPTION "Added cSdslSturAnnex for G.shdsl CPE device. Also updated description for cSdslStucAnnex. " REVISION "200101301600Z" DESCRIPTION "Added cSdslLineEquipmentType, cSdslLineAutoRateEnable. cSdslShdslLineMaxRate, cSdslStucPsdMaskType, cSdslStucAnnex, and cSdslStucThresholdSnrMgn. Changed default for cSdslLineMaxRate. Updated description for SNR and output pwr profile settings." ::= { ciscoMgmt 155 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.9.9.155.1 | ciscoSdslLineMIBObjects | 9 | 144 | None |
1.3.6.1.4.1.9.9.155.2 | ciscoSdslLineMIBNotificationsPrefix | 1 | 1 | None |
1.3.6.1.4.1.9.9.155.3 | ciscoSdslLineMIBConformance | 2 | 22 | None |
To many brothers! Only 100 nearest brothers are shown.
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
... | ||||
1.3.6.1.4.1.9.9.105 | ciscoC8500RedundancyMIB | 3 | 49 | This MIB allows management of redundancy of CPU and switch cards for the Catalyst 8540 switch, and other products with similar im… |
1.3.6.1.4.1.9.9.106 | ciscoHsrpMIB | 3 | 38 | ciscoHsrpMIB MODULE-IDENTITY LAST-UPDATED "9808030000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Custome… |
1.3.6.1.4.1.9.9.107 | ciscoHsrpExtMIB | 2 | 36 | ciscoHsrpExtMIB MODULE-IDENTITY LAST-UPDATED "9808030000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Cust… |
1.3.6.1.4.1.9.9.109 | ciscoProcessMIB | 3 | 187 | The MIB module to describe active system processes. |
1.3.6.1.4.1.9.9.110 | ciscoAtmSwitchFrRmMIB | 3 | 30 | This MIB module describes a set of objects used for switch Resource Management (RM) for Frame Relay/Frame based User-to-Network (… |
1.3.6.1.4.1.9.9.112 | ciscoAtmSwitchFrIwfMIB | 2 | 109 | A MIB module for managing Frame Relay to ATM interworking connections, and Frame Relay to Frame Relay switched connections via an… |
1.3.6.1.4.1.9.9.113 | ciscoCarMIB | 2 | 36 | Cisco CAR MIB - Overview Cisco Weighted Rate-limit, known as Commited Access Rate (CAR), is a traffic control method which uses a… |
1.3.6.1.4.1.9.9.114 | ciscoCableSpectrumMIB | 3 | 162 | This is the MIB Module for Cable Spectrum Management for DOCSIS-compliant Cable Modem Termination Systems (CMTS). Spectrum manage… |
1.3.6.1.4.1.9.9.115 | ciscoCasaFaMIB | 3 | 78 | This MIB module in conjunction with the CISCO-CASA-MIB, defines the SNMP management information base for managing the Cisco Appli… |
1.3.6.1.4.1.9.9.116 | ciscoDocsExtMIB | 3 | 235 | This is the MIB module for the Cisco specific extension objects of Data Over Cable Service, Radio Frequency interface. There is … |
1.3.6.1.4.1.9.9.117 | ciscoEntityFRUControlMIB | 3 | 147 | The CISCO-ENTITY-FRU-CONTROL-MIB is used to monitor and configure operational status of Field Replaceable Units (FRUs) and other … |
1.3.6.1.4.1.9.9.118 | ciscoUdldpMIB | 3 | 51 | Cisco Uni Direction Link Detection Protocol MIB |
1.3.6.1.4.1.9.9.120 | ciscoNetworkRegistrarMIB | 3 | 125 | MIB for Cisco Network Registrar (CNR). |
1.3.6.1.4.1.9.9.121 | ciscoAtmNetworkClockMIB | 3 | 53 | The MIB module for management of network clock distribution and the Network Clock Distribution Protocol (NCDP) in Cisco de… |
1.3.6.1.4.1.9.9.122 | ciscoCasaMIB | 3 | 78 | This MIB contains the basic objects for managing a Cisco Appliance Services Architecture (CASA) Entity. A CASA Entity can be a Ma… |
1.3.6.1.4.1.9.9.124 | ciscoCallResourcePoolMIB | 3 | 114 | The MIB module for call resource pool management. This MIB supports the resource pool manager feature of CISCO IOS. This feature … |
1.3.6.1.4.1.9.9.125 | ciscoWANRsrcPartMIB | 2 | 55 | The MIB module to manage resource partition objects. A resource partition is configured on a virtual interface (ifType value atmV… |
1.3.6.1.4.1.9.9.126 | ciscoSonetMIB | 3 | 136 | The MIB module to describe SONET/SDH interfaces objects. This is an extension to the standard SONET MIB(RFC 2558). |
1.3.6.1.4.1.9.9.128 | ciscoVlanIfTableRelationshipMIB | 1 | 12 | ciscoVlanIftableRelationshipMIB |
1.3.6.1.4.1.9.9.129 | ciscoAtmVirtualIfMIB | 2 | 139 | The MIB module to manage ATM Virtual interface objects. ATM virtual interfaces are configured on a physical line. |
1.3.6.1.4.1.9.9.130 | ciscoAdslDmtLineMIB | 3 | 72 | This MIB module serves as an enterprise-specific extension of the ADSL-LINE-MIB. The structure of this MIB module shadows the st… |
1.3.6.1.4.1.9.9.131 | ciscoSystemMIB | 3 | 57 | The systemGroup (see RFC 1907) provides a standard set of basic system information. This MIB module contains Cisco-defined exten… |
1.3.6.1.4.1.9.9.132 | ciscoDs3MIB | 2 | 140 | The MIB module to describe DS3 line objects. This is an extension to the standard DS3 MIB(RFC 2496). |
1.3.6.1.4.1.9.9.133 | ciscoAtmCellLayerMIB | 1 | 138 | The MIB module to describe ATM cell layer objects and statistics of a physical line. |
1.3.6.1.4.1.9.9.134 | ciscoClusterMIB | 3 | 49 | The MIB module for the management of a group of devices called a 'cluster'. A cluster comprises: 1. A command switch, which is a… |
1.3.6.1.4.1.9.9.135 | ciscoWirelessP2pBpiMIB | 3 | 66 | This is the MIB Module for the Baseline Privacy Interface (BPI) at Point to Point Wireless Radio Card. This is a specialization o… |
1.3.6.1.4.1.9.9.136 | ciscoWirelessIfMIB | 3 | 307 | This is the MIB Module for the Cisco Wireless Radio Point to Point interface specification. I) Relationship of the Cisco Wireless… |
1.3.6.1.4.1.9.9.137 | ciscoWirelessTextualConventions | 0 | 0 | This module defines textual conventions used in Cisco Wireless MIBs. |
1.3.6.1.4.1.9.9.138 | ciscoEntityAlarmMIB | 3 | 66 | This MIB module defines the managed objects that support the monitoring of alarms generated by physical entities contained by the… |
1.3.6.1.4.1.9.9.139 | ciscoEntityProvMIB | 3 | 13 | This MIB module defines the objects that support provisioning of 'container' class physical entities. Provisioning sets up a 'co… |
1.3.6.1.4.1.9.9.140 | ciscoCopsClientMIB | 3 | 43 | This MIB module is for configuration & statistic query of Common Open Policy Service(COPS) client feature on the Cisco device. C… |
1.3.6.1.4.1.9.9.141 | ciscoVSIControllerMIB | 2 | 21 | This MIB module is used for configuring ATM Capable Switch to be aware of VSI Controller information. Terminolgies used: VSI … |
1.3.6.1.4.1.9.9.144 | ciscoTransactionConnectionMIB | 2 | 66 | The MIB module for retrieving Cisco Transaction Connection configuration and status. Cisco Transaction Connection routes transac… |
1.3.6.1.4.1.9.9.145 | ciscoWanModuleMIB | 3 | 32 | The MIB to configure Connection Specific parameters and statistics related information in a Service Module. The Service Module(SM… |
1.3.6.1.4.1.9.9.146 | ciscoCallApplicationMIB | 2 | 548 | This MIB allows management of call applications on a network device. A 'call application' is a software module that processes cal… |
1.3.6.1.4.1.9.9.147 | ciscoFirewallMIB | 3 | 75 | MIB module for monitoring Cisco Firewalls. |
1.3.6.1.4.1.9.9.148 | ciscoBgpPolAcctMIB | 2 | 15 | BGP policy based accounting information |
1.3.6.1.4.1.9.9.149 | ciscoAdslLineCapMIB | 3 | 46 | This MIB module serves as an enterprise-specific extension of the ADSL-LINE-MIB. The structure of this MIB module shadows the st… |
1.3.6.1.4.1.9.9.150 | ciscoAAASessionMIB | 3 | 31 | This MIB module provides data for accounting sessions based on Authentication, Authorization, Accounting (AAA) protocols. Referenc… |
1.3.6.1.4.1.9.9.151 | ciscoL2L3IfConfigMIB | 2 | 11 | Interface switchport mode configuration management MIB. This MIB is used to monitor and control configuration of interface switch… |
1.3.6.1.4.1.9.9.152 | ciscoSipUaMIB | 4 | 504 | Cisco User Agent Session Initiation Protocol (SIP) MIB module. SIP is an application-layer signalling protocol for creating, mod… |
1.3.6.1.4.1.9.9.154 | ciscoIdslLineMIB | 3 | 148 | This MIB module describes IDSL (ISDN Digital Line Subscriber) line interfaces. The structure of this module resembles that of th… |
1.3.6.1.4.1.9.9.156 | ciscoCcmMIB | 3 | 487 | The MIB Module for the management of a Cisco Unified Communications Manager (CUCM) application running with a Cisco Communication… |
1.3.6.1.4.1.9.9.157 | ciscoCdmaPdsnMIB | 3 | 984 | This MIB is to support the CDMA PDSN (Packet Data Serving Node) feature. A CDMA2000 network supports wireless data communication… |
1.3.6.1.4.1.9.9.158 | ciscoAAAClientMIB | 3 | 25 | This MIB module provides data for authentication method priority based on Authentication, Authorization, Accounting (AAA) protoco… |
1.3.6.1.4.1.9.9.159 | ciscoQosPolicyConfigMIB | 3 | 35 | This MIB module defines managed objects that support the policy source configuration of Quality of Service (QoS) on the device. T… |
1.3.6.1.4.1.9.9.160 | ciscoCircuitInterfaceMIB | 2 | 11 | The MIB module to configure the circuit description for an interface. The circuit description can be used to describe and identify… |
1.3.6.1.4.1.9.9.161 | ciscoSlbMIB | 3 | 279 | The MIB for managing Server Load Balancing Manager(s), such as the Cisco IOS SLB product. This MIB includes instrumentation for t… |
1.3.6.1.4.1.9.9.162 | ciscoVsiMasterMIB | 3 | 100 | This MIB module contains objects related to the master side of the Virtual Switch Interface protocol used for control of ATM swit… |
1.3.6.1.4.1.9.9.163 | ciscoCallTrackerMIB | 3 | 104 | CISCO-CALL-TRACKER-MIB |
1.3.6.1.4.1.9.9.164 | ciscoCallTrackerTCPMIB | 3 | 25 | This MIB module provides TCP service connection related data for tracking the progress and status of a call. This module extends t… |
1.3.6.1.4.1.9.9.165 | ciscoCallTrackerModemMIB | 3 | 97 | This MIB module provides modem call related data for tracking the progress and status of a call. This module extends tables defin… |
1.3.6.1.4.1.9.9.166 | ciscoCBQosMIB | 2 | 544 | Cisco Class-Based QoS MIB ********************************** Overview ********************************** This MIB provides read acc… |
1.3.6.1.4.1.9.9.167 | ciscoWirelessDocsIfMib | 3 | 140 | This is the MIB Module for MCNS compliant Radio Frequency (RF) interfaces in wireless point-to-multipoint subscriber units (SU) a… |
1.3.6.1.4.1.9.9.168 | ciscoNtpMIB | 3 | 87 | This MIB module defines a MIB which provides mechanisms to monitor an NTP server. The MIB is derived from the Technical Report #Ma… |
1.3.6.1.4.1.9.9.169 | ciscoWirelessDocsExtMIB | 3 | 99 | This MIB module defines Cisco-specific objects that add to the functionality defined in CISCO-WIRELESS-DOCS-IF-MIB. These objects … |
1.3.6.1.4.1.9.9.170 | ciscoWirelessPhyMIB | 2 | 112 | This is the MIB Module for the Cisco Wireless Radio Point to MultiPoint interface. |
1.3.6.1.4.1.9.9.171 | ciscoIpSecFlowMonitorMIB | 3 | 507 | This is a MIB Module for monitoring the structures in IPSec-based Virtual Private Networks. The MIB has been designed to be adopt… |
1.3.6.1.4.1.9.9.172 | ciscoIpSecPolMapMIB | 3 | 21 | The MIB module maps the IPSec entities created dynamically to the policy entities that caused them. This is an appendix to the IPS… |
1.3.6.1.4.1.9.9.173 | ciscoPrivateVlanMIB | 2 | 56 | The MIB module to support Private VLAN feature on Cisco's switching devices. |
1.3.6.1.4.1.9.9.174 | ciscoMobileIpMIB | 3 | 533 | An extension to the IETF MIB module defined in RFC-2006 for managing Mobile IP implementations. Mobile IP introduces the followin… |
1.3.6.1.4.1.9.9.175 | ciscoIfLinkConfigMIB | 2 | 15 | The MIB module for configuration of bulk distribution (de-multiplexing of traffic from higher-bandwidth to lower-bandwidth interf… |
1.3.6.1.4.1.9.9.176 | ciscoRFMIB | 3 | 117 | This MIB provides configuration control and status for the Redundancy Framework (RF) subsystem. RF provides a mechanism for logic… |
1.3.6.1.4.1.9.9.177 | ciscoSaaApmMIB | 3 | 38 | Acronyms and Terms: SAA - Service Assurance Agent APM - Application Performance Monitoring A MIB for controlling SAA APM. APM provi… |
1.3.6.1.4.1.9.9.178 | ciscoContentEngineMIB | 3 | 263 | The MIB module for the Cisco Content Engine from Cisco Systems, Inc. |
1.3.6.1.4.1.9.9.179 | ciscoCatOSAclQosMIB | 3 | 470 | This MIB module is for Access Control Lists(ACLs) configuration of Quality of Service (QoS) as well as Security feature on the Ci… |
1.3.6.1.4.1.9.9.180 | ciscoWirelessRfMetricsMIB | 5 | 99 | This is the MIB Module for the Cisco Wireless Radio Point to MultiPoint interface specification. |
1.3.6.1.4.1.9.9.181 | ciscoWirelessLinkMetricsMIB | 4 | 141 | This is the MIB Module for the Cisco Wireless Radio Point to MultiPoint interface link metrics specification. Glossary The followin… |
1.3.6.1.4.1.9.9.183 | ciscoGprsAccPtMIB | 3 | 338 | This MIB module supports access point configuration for GGSN in a GPRS system. GPRS [1] is a GSM network providing mobile wireles… |
1.3.6.1.4.1.9.9.184 | ciscoPimMIB | 3 | 36 | This MIB module defines the cisco specific variables for Protocol Independent Multicast (PIM) management. These definitions are a… |
1.3.6.1.4.1.9.9.185 | ciscoBertMIB | 2 | 46 | The MIB module to configure and perform Bit Error Rate Testing (BERT) on DS3, DS1/E1 and DS0/DS0Bundle interfaces. Bit error rate… |
1.3.6.1.4.1.9.9.187 | ciscoBgp4MIB | 4 | 137 | An extension to the IETF BGP4 MIB module defined in RFC 1657. Following is the terminology associated with Border Gateway Protocol… |
1.3.6.1.4.1.9.9.188 | cGtpMIB | 3 | 248 | This MIB module manages the GPRS Tunnelling Protocol (GTP) on GGSN and SGSN. GPRS provides wireless access to packet data network… |
1.3.6.1.4.1.9.9.189 | ciscoPortQosMIB | 3 | 114 | Cisco PORT QOS MIB - Overview This MIB module is for the management of Cisco's per port rate-limiting and traffic shaping on L3 sw… |
1.3.6.1.4.1.9.9.190 | ciscoVoiceAppsMIB | 3 | 40 | The MIB Module for the management of Cisco Voice Applications. This MIB is designed to work in conjunction with the SYSAPPL-MIB … |
1.3.6.1.4.1.9.9.191 | ciscoIpUplinkRedirectMIB | 3 | 11 | This MIB module is for the configuration of Cisco IP Uplink Redirect feature. |
1.3.6.1.4.1.9.9.192 | ciscoGprsChargingMIB | 3 | 315 | This MIB module manages the charging related function on the GGSN node of a GPRS system. The following diagram illustrates a simp… |
1.3.6.1.4.1.9.9.194 | ciscoPppoeMIB | 3 | 89 | Cisco PPPoE sessions management MIB Module. |
1.3.6.1.4.1.9.9.195 | ciscoEntityExtMIB | 3 | 64 | This MIB is an extension of the ENTITY-MIB specified in RFC2737. This MIB module contains Cisco-defined extensions to the entit… |
1.3.6.1.4.1.9.9.197 | ciscoDistDirMIB | 3 | 123 | Cisco Distributed Director MIB. The Cisco Distributed Director provides global Internet scalability and increased performance as … |
1.3.6.1.4.1.9.9.198 | ciscoRfSupMIB | 3 | 58 | This MIB was designed to complement the CISCO-RF-MIB by providing additional optional status and configuration control for redund… |
1.3.6.1.4.1.9.9.199 | ciscoSmFileDownloadMIB | 3 | 23 | The MIB module for downloading files to the Service Modules specifically designed for an architecture containing a controller car… |
1.3.6.1.4.1.9.9.201 | ciscoSwitchUsageMIB | 3 | 15 | This MIB defines objects related to statistics for the usage of switch fabric. The switch fabric is used by the incoming packets … |
1.3.6.1.4.1.9.9.202 | ciscoOscpMIB | 3 | 52 | The MIB module for managing the Cisco Optical Supervisory Channel Protocol (OSCP). The OSCP is used to determine and maintain wav… |
1.3.6.1.4.1.9.9.204 | ciscoXdslLineMIB | 2 | 32 | The tables defined by this MIB module contain a collection of managed objects that are general in nature and apply to different t… |
... |