For devices that allows dynamic determination of whether
a link between two switches should be a trunk or not, this
object allows the operator to mandate the behavior of that
dynamic mechanism.
on(1) dictates that the interface will always be a
trunk. This is the value for static entries (those that
show no dynamic behavior). If the negotiation is supported
on this port, negotiation will take place with the far end
to attempt to bring the far end into trunking state.
off(2) allows an operator to specify that the specified
interface is never to be trunk, regardless of any dynamic
mechanisms to the contrary. This value is useful for
overriding the default behavior of some switches. If the
negotiation is supported on this port, negotiation will take
place with the far end to attempt on the link to bring the
far end into non-trunking state.
desirable(3) is used to indicate that it is desirable for
the interface to become a trunk. The device will initiate
any negotiation necessary to become a trunk but will not
become a trunk unless it receives confirmation from the far
end on the link.
auto(4) is used to indicate that the interface is capable
and willing to become a trunk but will not initiate
trunking negotiations. The far end on the link are
required to either start negotiations or start sending
encapsulated packets, on which event the specified
interface will become a trunk.
onNoNegotiate(5) is used to indicate that the interface is
permanently set to be a trunk, and no negotiation takes
place with the far end on the link to ensure consistent
operation. This is similar to on(1) except no negotiation
takes place with the far end.
If the port does not support negotiation or its
vlanTrunkPortEncapsulationType is set to negotiate(5),
onNoNegotiate(5) is not allowed.
Devices that do no support dynamic determination (for just
a particular interface, encapsulation or for the whole
device) need only support the 'on', and 'off' values.
Parsed from file CISCO-VTP-MIB.mib
Module: CISCO-VTP-MIB
For devices that allows dynamic determination of whether
a link between two switches should be a trunk or not, this
object allows the operator to mandate the behavior of that
dynamic mechanism.
on(1) dictates that the interface will always be a
trunk. This is the value for static entries (those that
show no dynamic behavior). If the negotiation is supported
on this port, negotiation will take place with the far end
to attempt to bring the far end into trunking state.
off(2) allows an operator to specify that the specified
interface is never to be trunk, regardless of any dynamic
mechanisms to the contrary. This value is useful for
overriding the default behavior of some switches. If the
negotiation is supported on this port, negotiation will take
place with the far end to attempt on the link to bring the
far end into non-trunking state.
desirable(3) is used to indicate that it is desirable for
the interface to become a trunk. The device will initiate
any negotiation necessary to become a trunk but will not
become a trunk unless it receives confirmation from the far
end on the link.
auto(4) is used to indicate that the interface is capable
and willing to become a trunk but will not initiate
trunking negotiations. The far end on the link are
required to either start negotiations or start sending
encapsulated packets, on which event the specified
interface will become a trunk.
onNoNegotiate(5) is used to indicate that the interface is
permanently set to be a trunk, and no negotiation takes
place with the far end on the link to ensure consistent
operation. This is similar to on(1) except no negotiation
takes place with the far end.
If the port does not support negotiation or its
vlanTrunkPortEncapsulationType is set to negotiate(5),
onNoNegotiate(5) is not allowed.
Devices that do no support dynamic determination (for just
a particular interface, encapsulation or for the whole
device) need only support the 'on', and 'off' values.
vlanTrunkPortDynamicState OBJECT-TYPE
SYNTAX INTEGER { on(1), off(2), desirable(3),
auto(4), onNoNegotiate(5) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For devices that allows dynamic determination of whether
a link between two switches should be a trunk or not, this
object allows the operator to mandate the behavior of that
dynamic mechanism.
on(1) dictates that the interface will always be a
trunk. This is the value for static entries (those that
show no dynamic behavior). If the negotiation is supported
on this port, negotiation will take place with the far end
to attempt to bring the far end into trunking state.
off(2) allows an operator to specify that the specified
interface is never to be trunk, regardless of any dynamic
mechanisms to the contrary. This value is useful for
overriding the default behavior of some switches. If the
negotiation is supported on this port, negotiation will take
place with the far end to attempt on the link to bring the
far end into non-trunking state.
desirable(3) is used to indicate that it is desirable for
the interface to become a trunk. The device will initiate
any negotiation necessary to become a trunk but will not
become a trunk unless it receives confirmation from the far
end on the link.
auto(4) is used to indicate that the interface is capable
and willing to become a trunk but will not initiate
trunking negotiations. The far end on the link are
required to either start negotiations or start sending
encapsulated packets, on which event the specified
interface will become a trunk.
onNoNegotiate(5) is used to indicate that the interface is
permanently set to be a trunk, and no negotiation takes
place with the far end on the link to ensure consistent
operation. This is similar to on(1) except no negotiation
takes place with the far end.
If the port does not support negotiation or its
vlanTrunkPortEncapsulationType is set to negotiate(5),
onNoNegotiate(5) is not allowed.
Devices that do no support dynamic determination (for just
a particular interface, encapsulation or for the whole
device) need only support the on, and off values."
View at oid-info.com
For devices that allows dynamic determination of whether
a link between two switches should be a trunk or not, this object
allows the operator to mandate the behavior of that dynamic
mechanism.
on(1) dictates that the interface will always be a
trunk. This is the value for static entries (those that
show no dynamic behavior). If the negotiation is supported on this
port, negotiation will take place with the far end to attempt
to bring the far end into trunking state.
off(2) allows an operator to specify that the specified
interface is never to be trunk, regardless of any dynamic
mechanisms to the contrary. This value is useful for
overriding the default behavior of some switches. If the
negotiation is supported on this port, negotiation will take place
with the far end to attempt on the link to bring the far end into
non-trunking state.
desirable(3) is used to indicate that it is desirable for
the interface to become a trunk. The device will initiate
any negotiation necessary to become a trunk but will not
become a trunk unless it receives confirmation from the far
end on the link.
auto(4) is used to indicate that the interface is capable
and willing to become a trunk but will not initiate
trunking negotiations. The far end on the link are
required to either start negotiations or start sending
encapsulated packets, on which event the specified
interface will become a trunk.
onNoNegotiate(5) is used to indicate that the interface is permanently
set to be a trunk, and no negotiation takes place with the
far end on the link to ensure consistent operation. This is similar
to on(1) except no negotiation takes place with the far end.
If the port does not support negotiation or its
vlanTrunkPortEncapsulationType is set to negotiate(5),
onNoNegotiate(5) is not allowed.
Devices that do no support dynamic determination (for just
a particular interface, encapsulation or for the whole
device) need only support the 'on', and 'off' values.
Parsed from file cisco-vtp.mib.txt
Company: None
Module: CISCO-VTP-MIB
For devices that allows dynamic determination of whether
a link between two switches should be a trunk or not, this
object allows the operator to mandate the behavior of that
dynamic mechanism.
on(1) dictates that the interface will always be a
trunk. This is the value for static entries (those that
show no dynamic behavior). If the negotiation is supported
on this port, negotiation will take place with the far end
to attempt to bring the far end into trunking state.
off(2) allows an operator to specify that the specified
interface is never to be trunk, regardless of any dynamic
mechanisms to the contrary. This value is useful for
overriding the default behavior of some switches. If the
negotiation is supported on this port, negotiation will take
place with the far end to attempt on the link to bring the
far end into non-trunking state.
desirable(3) is used to indicate that it is desirable for
the interface to become a trunk. The device will initiate
any negotiation necessary to become a trunk but will not
become a trunk unless it receives confirmation from the far
end on the link.
auto(4) is used to indicate that the interface is capable
and willing to become a trunk but will not initiate
trunking negotiations. The far end on the link are
required to either start negotiations or start sending
encapsulated packets, on which event the specified
interface will become a trunk.
onNoNegotiate(5) is used to indicate that the interface is
permanently set to be a trunk, and no negotiation takes
place with the far end on the link to ensure consistent
operation. This is similar to on(1) except no negotiation
takes place with the far end.
If the port does not support negotiation or its
vlanTrunkPortEncapsulationType is set to negotiate(5),
onNoNegotiate(5) is not allowed.
Devices that do no support dynamic determination (for just
a particular interface, encapsulation or for the whole
device) need only support the 'on', and 'off' values.
vlanTrunkPortDynamicState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), desirable(3), auto(4), onNoNegotiate(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "For devices that allows dynamic determination of whether a link between two switches should be a trunk or not, this object allows the operator to mandate the behavior of that dynamic mechanism. on(1) dictates that the interface will always be a trunk. This is the value for static entries (those that show no dynamic behavior). If the negotiation is supported on this port, negotiation will take place with the far end to attempt to bring the far end into trunking state. off(2) allows an operator to specify that the specified interface is never to be trunk, regardless of any dynamic mechanisms to the contrary. This value is useful for overriding the default behavior of some switches. If the negotiation is supported on this port, negotiation will take place with the far end to attempt on the link to bring the far end into non-trunking state. desirable(3) is used to indicate that it is desirable for the interface to become a trunk. The device will initiate any negotiation necessary to become a trunk but will not become a trunk unless it receives confirmation from the far end on the link. auto(4) is used to indicate that the interface is capable and willing to become a trunk but will not initiate trunking negotiations. The far end on the link are required to either start negotiations or start sending encapsulated packets, on which event the specified interface will become a trunk. onNoNegotiate(5) is used to indicate that the interface is permanently set to be a trunk, and no negotiation takes place with the far end on the link to ensure consistent operation. This is similar to on(1) except no negotiation takes place with the far end. If the port does not support negotiation or its vlanTrunkPortEncapsulationType is set to negotiate(5), onNoNegotiate(5) is not allowed. Devices that do no support dynamic determination (for just a particular interface, encapsulation or for the whole device) need only support the 'on', and 'off' values." ::= { vlanTrunkPortEntry 13 }
vlanTrunkPortDynamicState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), desirable(3), auto(4), onNoNegotiate(5) } ACCESS read-write STATUS mandatory DESCRIPTION "For devices that allows dynamic determination of whether a link between two switches should be a trunk or not, this object allows the operator to mandate the behavior of that dynamic mechanism. on(1) dictates that the interface will always be a trunk. This is the value for static entries (those that show no dynamic behavior). If the negotiation is supported on this port, negotiation will take place with the far end to attempt to bring the far end into trunking state. off(2) allows an operator to specify that the specified interface is never to be trunk, regardless of any dynamic mechanisms to the contrary. This value is useful for overriding the default behavior of some switches. If the negotiation is supported on this port, negotiation will take place with the far end to attempt on the link to bring the far end into non-trunking state. desirable(3) is used to indicate that it is desirable for the interface to become a trunk. The device will initiate any negotiation necessary to become a trunk but will not become a trunk unless it receives confirmation from the far end on the link. auto(4) is used to indicate that the interface is capable and willing to become a trunk but will not initiate trunking negotiations. The far end on the link are required to either start negotiations or start sending encapsulated packets, on which event the specified interface will become a trunk. onNoNegotiate(5) is used to indicate that the interface is permanently set to be a trunk, and no negotiation takes place with the far end on the link to ensure consistent operation. This is similar to on(1) except no negotiation takes place with the far end. If the port does not support negotiation or its vlanTrunkPortEncapsulationType is set to negotiate(5), onNoNegotiate(5) is not allowed. Devices that do no support dynamic determination (for just a particular interface, encapsulation or for the whole device) need only support the 'on', and 'off' values." ::= { vlanTrunkPortEntry 13 }
Automatically extracted from a file named C-VTP
vlanTrunkPortDynamicState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), desirable(3), auto(4), onNoNegotiate(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "For devices that allows dynamic determination of whether a link between two switches should be a trunk or not, this object allows the operator to mandate the behavior of that dynamic mechanism. on(1) dictates that the interface will always be a trunk. This is the value for static entries (those that show no dynamic behavior). If the negotiation is supported on this port, negotiation will take place with the far end to attempt to bring the far end into trunking state. off(2) allows an operator to specify that the specified interface is never to be trunk, regardless of any dynamic mechanisms to the contrary. This value is useful for overriding the default behavior of some switches. If the negotiation is supported on this port, negotiation will take place with the far end to attempt on the link to bring the far end into non-trunking state. desirable(3) is used to indicate that it is desirable for the interface to become a trunk. The device will initiate any negotiation necessary to become a trunk but will not become a trunk unless it receives confirmation from the far end on the link. auto(4) is used to indicate that the interface is capable and willing to become a trunk but will not initiate trunking negotiations. The far end on the link are required to either start negotiations or start sending encapsulated packets, on which event the specified interface will become a trunk. onNoNegotiate(5) is used to indicate that the interface is permanently set to be a trunk, and no negotiation takes place with the far end on the link to ensure consistent operation. This is similar to on(1) except no negotiation takes place with the far end. If the port does not support negotiation or its vlanTrunkPortEncapsulationType is set to negotiate(5), onNoNegotiate(5) is not allowed. Devices that do no support dynamic determination (for just a particular interface, encapsulation or for the whole device) need only support the 'on', and 'off' values." ::= { vlanTrunkPortEntry 13 }
vlanTrunkPortDynamicState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), desirable(3), auto(4), onNoNegotiate(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "For devices that allows dynamic determination of whether a link between two switches should be a trunk or not, this object allows the operator to mandate the behavior of that dynamic mechanism. on(1) dictates that the interface will always be a trunk. This is the value for static entries (those that show no dynamic behavior). If the negotiation is supported on this port, negotiation will take place with the far end to attempt to bring the far end into trunking state. off(2) allows an operator to specify that the specified interface is never to be trunk, regardless of any dynamic mechanisms to the contrary. This value is useful for overriding the default behavior of some switches. If the negotiation is supported on this port, negotiation will take place with the far end to attempt on the link to bring the far end into non-trunking state. desirable(3) is used to indicate that it is desirable for the interface to become a trunk. The device will initiate any negotiation necessary to become a trunk but will not become a trunk unless it receives confirmation from the far end on the link. auto(4) is used to indicate that the interface is capable and willing to become a trunk but will not initiate trunking negotiations. The far end on the link are required to either start negotiations or start sending encapsulated packets, on which event the specified interface will become a trunk. onNoNegotiate(5) is used to indicate that the interface is permanently set to be a trunk, and no negotiation takes place with the far end on the link to ensure consistent operation. This is similar to on(1) except no negotiation takes place with the far end. If the port does not support negotiation or its vlanTrunkPortEncapsulationType is set to negotiate(5), onNoNegotiate(5) is not allowed. Devices that do no support dynamic determination (for just a particular interface, encapsulation or for the whole device) need only support the 'on', and 'off' values." ::= { vlanTrunkPortEntry 13 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.46.1.6.1.1.1 | vlanTrunkPortIfIndex | 0 | 0 | The value of ifIndex for the interface corresponding to this trunk port. |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.2 | vlanTrunkPortManagementDomain | 0 | 0 | The value of managementDomainIndex for the management domain on this trunk port. Devices which support only one management domai… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.3 | vlanTrunkPortEncapsulationType | 0 | 0 | The type of VLAN encapsulation used on this trunk port. Whether writing to this object in order to modify the encapsulation is su… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.4 | vlanTrunkPortVlansEnabled | 0 | 0 | vlanTrunkPortVlansEnabled OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A str… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.5 | vlanTrunkPortNativeVlan | 0 | 0 | The VlanIndex of the VLAN which is represented by native frames on this trunk port. For trunk ports not supporting the sending a… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.6 | vlanTrunkPortRowStatus | 0 | 0 | The status of this row. In some circumstances, the creation of a row in this table is needed to enable the appropriate trunking/… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.7 | vlanTrunkPortInJoins | 0 | 0 | The number of VTP Join messages received on this trunk port. |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.8 | vlanTrunkPortOutJoins | 0 | 0 | The number of VTP Join messages sent on this trunk port. |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.9 | vlanTrunkPortOldAdverts | 0 | 0 | The number of VTP Advertisement messages which indicated the sender does not support VLAN-pruning received on this trunk port. |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.10 | vlanTrunkPortVlansPruningEligible | 0 | 0 | vlanTrunkPortVlansPruningEligible OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-create STATUS current DESCRIPTIO… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.11 | vlanTrunkPortVlansXmitJoined | 0 | 0 | A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.12 | vlanTrunkPortVlansRcvJoined | 0 | 0 | A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.14 | vlanTrunkPortDynamicStatus | 0 | 0 | Indicates whether the specified interface is either acting as a trunk or not. This is a result of the vlanTrunkPortDynamicState a… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.15 | vlanTrunkPortVtpEnabled | 0 | 0 | Some trunk interface modules allow VTP to be enabled/disabled seperately from that of the central device. In such a case this ob… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.16 | vlanTrunkPortEncapsulationOperType | 0 | 0 | The type of VLAN encapsulation in use on this trunk port. For intefaces with vlanTrunkPortDynamicStatus of notTrunking(2) the vla… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.17 | vlanTrunkPortVlansEnabled2k | 0 | 0 | vlanTrunkPortVlansEnabled2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.18 | vlanTrunkPortVlansEnabled3k | 0 | 0 | vlanTrunkPortVlansEnabled3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.19 | vlanTrunkPortVlansEnabled4k | 0 | 0 | vlanTrunkPortVlansEnabled4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.20 | vtpVlansPruningEligible2k | 0 | 0 | vtpVlansPruningEligible2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A … |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.21 | vtpVlansPruningEligible3k | 0 | 0 | vtpVlansPruningEligible3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A … |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.22 | vtpVlansPruningEligible4k | 0 | 0 | vtpVlansPruningEligible4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A … |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.23 | vlanTrunkPortVlansXmitJoined2k | 0 | 0 | A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on t… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.24 | vlanTrunkPortVlansXmitJoined3k | 0 | 0 | A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on t… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.25 | vlanTrunkPortVlansXmitJoined4k | 0 | 0 | A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on t… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.26 | vlanTrunkPortVlansRcvJoined2k | 0 | 0 | A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on t… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.27 | vlanTrunkPortVlansRcvJoined3k | 0 | 0 | A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on t… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.28 | vlanTrunkPortVlansRcvJoined4k | 0 | 0 | A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on t… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.29 | vlanTrunkPortDot1qTunnel | 0 | 0 | Indicates dot1qtunnel mode of the port. If the portDot1qTunnel is set to 'trunk' mode, the port's vlanTrunkPortDynamicState will… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.30 | vlanTrunkPortVlansActiveFirst2k | 0 | 0 | A string of octets containing one bit per VLAN with VlanIndex values of 0 through 2047. If the bit corresponding to a VLAN is set… |
| 1.3.6.1.4.1.9.9.46.1.6.1.1.31 | vlanTrunkPortVlansActiveSecond2k | 0 | 0 | A string of octets containing one bit per VLAN with VlanIndex values of 2048 through 4095. If the bit corresponding to a VLAN is … |