This object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames which contains an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC 1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0.
Status in source: current.
Names: wmanIfCmnClassifierRuleEnetProtocolType
Technical details
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"wmanIfCmnClassifierRuleEnetProtocolType",
"OBJECT-TYPE",
"SYNTAX",
"INTEGER",
"{",
"none",
"(",
"0",
")",
",",
"ethertype",
"(",
"1",
")",
",",
"dsap",
"(",
"2",
")",
"}",
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"This object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames which contains an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC 1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0.\"",
"REFERENCE",
"\"Section 11.13.19.3.4.10 in IEEE 802.16REVd/D5-2004\"",
"::=",
"{",
"wmanIfCmnClassifierRuleEntry",
"21",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"INTEGER",
[
"enumSpec",
[
[
"none",
0
],
[
"ethertype",
1
],
[
"dsap",
2
]
]
]
],
null,
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"This object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames which contains an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC 1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0."
],
[
"REFERENCE",
"Section 11.13.19.3.4.10 in IEEE 802.16REVd/D5-2004"
],
null,
null,
null
]
}- etsi-formal
· Publisher's source file
Source location: PDF page 74/WMAN-IF-MIB::wmanIfCmnClassifierRuleEnetProtocolType.Source version and references
Published package: ETSI TS 102389 1.1.1; file: ts_102389v010101p.pdf.
Downloaded: 2026-10-19T23:15:36.254096+00:00. SHA-256:
624ae041d6abee4b6cf0a5b3bf2ae2b0e602a96229c82d5ac5ed39f9c531f2d1{'kind': 'OBJECT-TYPE', 'details': {'module': 'WMAN-IF-MIB', 'imports': {'IF-MIB': ['ifIndex', 'InterfaceIndexOrZero'], 'SNMPv2-TC': ['TEXTUAL-CONVENTION', 'MacAddress', 'RowStatus', 'TruthValue', 'DateAndTime', 'DisplayString', 'TimeInterval', 'TimeStamp'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'NOTIFICATION-TYPE', 'Unsigned32', 'Integer32', 'Counter32', 'Counter64', 'TimeTicks', 'IpAddress', 'transmission'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}, 'document': {'language': 'pdf', 'pdf_page': 74, 'software': 'ETSI TS 102389', 'extraction_note': 'Definition is pdftotext output; locate it by module/symbol on the stated physical PDF page, not by a claimed byte offset', 'release_version': '1.1.1'}, 'smi_kind': 'OBJECT-TYPE', 'definition': 'wmanIfCmnClassifierRuleEnetProtocolType OBJECT-TYPE\n SYNTAX INTEGER {none(0),\n ethertype(1),\n dsap(2)}\n MAX-ACCESS read-only\n STATUS current\n DESCRIPTION\n "This object indicates the format of the layer 3 protocol\n id in the Ethernet packet. A value of none(0) means that\n the rule does not use the layer 3 protocol type as a\n matching criteria. A value of ethertype(1) means that the\n rule applies only to frames which contains an EtherType\n value. Ethertype values are contained in packets using\n the Dec-Intel-Xerox (DIX) encapsulation or the RFC 1042\n Sub-Network Access Protocol (SNAP) encapsulation formats.\n A value of dsap(2) means that the rule applies only to\n frames using the IEEE802.3 encapsulation format with a\n Destination Service Access Point (DSAP) other than 0xAA\n (which is reserved for SNAP). If the Ethernet frame\n contains an 802.1P/Q Tag header (i.e. EtherType 0x8100),\n this object applies to the embedded EtherType field within\n the 802.1P/Q header. If the referenced parameter is not\n present in a classifier, this object reports the value of\n 0."\n REFERENCE\n "Section 11.13.19.3.4.10 in IEEE 802.16REVd/D5-2004"\n ::= { wmanIfCmnClassifierRuleEntry 21 }', 'syntax_tree': [['SimpleSyntax', 'INTEGER', ['enumSpec', [['none', 0], ['ethertype', 1], ['dsap', 2]]]], None, ['MaxAccessPart', 'read-only'], ['Status', 'current'], ['DESCRIPTION', 'This object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames which contains an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC 1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0.'], ['REFERENCE', 'Section 11.13.19.3.4.10 in IEEE 802.16REVd/D5-2004'], None, None, None], 'source_encoding': 'utf-8-sig'}, 'parser_version': 'formal-3-q1'}