OID reference

vdslPhysCurrStatus

1.3.6.1.2.1.10.97.1.1.2.1.7

Description

Indicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There are no defects on the line. 1 lossOfFraming Vtu failure due to not receiving a valid frame. 2 lossOfSignal Vtu failure due to not receiving signal. 3 lossOfPower Vtu failure due to loss of…

Full description and source information

Identification

Identifier and names

Parent
1.3.6.1.2.1.10.97.1.1.2.1 (vdslPhysEntry)
Node code
7
Node name
vdslPhysCurrStatus
Category
SNMP management object
Numeric OID
1.3.6.1.2.1.10.97.1.1.2.1.7
URN notation
urn:oid:1.3.6.1.2.1.10.97.1.1.2.1.7
Type
OBJECT-TYPE
ASN.1, OID-IRI and named path variants
ASN.1 notation

{1 3 6 1 2 1 10 97 1 1 2 1 7}

  • {iso(1) identified-organization(3) dod(6) internet(1) mgmt(2) mib-2(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) identified-organization(3) dod(6) internet(1) mgmt(2) mib(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) identified-organization(3) dod(6) internet(1) mgmt(2) stdmib-2(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) org(3) dod(6) internet(1) mgmt(2) mib-2(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) org(3) dod(6) internet(1) mgmt(2) mib(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) org(3) dod(6) internet(1) mgmt(2) stdmib-2(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) mgmt(2) mib-2(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) mgmt(2) mib(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) mgmt(2) stdmib-2(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) iso-organization(3) dod(6) internet(1) mgmt(2) mib-2(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) iso-organization(3) dod(6) internet(1) mgmt(2) mib(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
  • {iso(1) iso-organization(3) dod(6) internet(1) mgmt(2) stdmib-2(1) transmission(10) vdslMIB(97) vdslLineMib(1) vdslMibObjects(1) vdslPhysTable(2) vdslPhysEntry(1) vdslPhysCurrStatus(7)}
OID-IRI notation
  • /1/3/6/1/2/1/10/97/1/1/2/1/7
  • /ISO/Identified-Organization/6/1/2/1/10/97/1/1/2/1/7
  • /ISO/3/6/1/2/1/10/97/1/1/2/1/7
Named path variants
  • /iso/identified-organization/dod/internet/mgmt/mib-2/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/identified-organization/dod/internet/mgmt/mib/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/identified-organization/dod/internet/mgmt/RFC1066-MIB-INTERPRETATION/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/identified-organization/dod/internet/mgmt/stdmib-2/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/org/dod/internet/mgmt/mib-2/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/org/dod/internet/mgmt/mib/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/org/dod/internet/mgmt/RFC1066-MIB-INTERPRETATION/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/org/dod/internet/mgmt/stdmib-2/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/iso-identified-organization/dod/internet/mgmt/mib-2/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/iso-identified-organization/dod/internet/mgmt/mib/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/iso-identified-organization/dod/internet/mgmt/RFC1066-MIB-INTERPRETATION/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/iso-identified-organization/dod/internet/mgmt/stdmib-2/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/iso-organization/dod/internet/mgmt/mib-2/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/iso-organization/dod/internet/mgmt/mib/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/iso-organization/dod/internet/mgmt/RFC1066-MIB-INTERPRETATION/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus
  • /iso/iso-organization/dod/internet/mgmt/stdmib-2/transmission/vdslMIB/vdslLineMib/vdslMibObjects/vdslPhysTable/vdslPhysEntry/vdslPhysCurrStatus

SNMP properties

Value type
BITS
Maximum access defined by MIB
read-only
Status in MIB
current

Bit values

Bit positionName
0noDefect
1lossOfFraming
2lossOfSignal
3lossOfPower
4lossOfSignalQuality
5lossOfLink
6dataInitFailure
7configInitFailure
8protocolInitFailure
9noPeerVtuPresent

Using this OID with SNMP

At least one MIB declaration places this object in a table row. A value belongs to a row instance; its suffix depends on the row's INDEX or AUGMENTS definition. The index encoding is not inferred here.

Published row index: ifIndex, vdslPhysSide.

snmpwalk [connection options] DEVICE .1.3.6.1.2.1.10.97.1.1.2.1.7

Replace the placeholders with your connection and authentication options. Available permissions and device support can differ from the MIB.

Properties come from available MIB definitions. Actual device support and access can differ. See source records below for original files and qualifications.

Meaning

Descriptions

2 unique

Identical descriptions are grouped. Different wording and device-specific notes are retained.

Description 1

Indicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There are no defects on the line. 1 lossOfFraming Vtu failure due to not receiving a valid frame. 2 lossOfSignal Vtu failure due to not receiving signal. 3 lossOfPower Vtu failure due to loss of power. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink Vtu failure due to inability to link with peer Vtu. Set whenever the transceiver is in the Warm Start state. 6 dataInitFailure Vtu failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure Vtu failure during initialization due to peer Vtu not able to support requested configuration. 8 protocolInitFailure Vtu failure during initialization due to incompatible protocol used by the peer Vtu. 9 noPeerVtuPresent Vtu failure during initialization due to no activation sequence detected from peer Vtu. This is intended to supplement ifOperStatus.
Original text from OID Repository
vdslPhysCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
lossOfFraming(1),
lossOfSignal(2),
lossOfPower(3),
lossOfSignalQuality(4),
lossOfLink(5),
dataInitFailure(6),
configInitFailure(7),
protocolInitFailure(8),
noPeerVtuPresent(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state of the Vtu line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There are no defects on the line.
1 lossOfFraming Vtu failure due to not receiving
a valid frame.
2 lossOfSignal Vtu failure due to not receiving
signal.
3 lossOfPower Vtu failure due to loss of power.
4 lossOfSignalQuality Loss of Signal Quality is declared
when the Noise Margin falls below
the Minimum Noise Margin, or the
bit-error-rate exceeds 10^-7.
5 lossOfLink Vtu failure due to inability to
link with peer Vtu. Set whenever
the transceiver is in the Warm
Start state.
6 dataInitFailure Vtu failure during initialization
due to bit errors corrupting
startup exchange data.
7 configInitFailure Vtu failure during initialization
due to peer Vtu not able to
support requested configuration.
8 protocolInitFailure Vtu failure during initialization
due to incompatible protocol used
by the peer Vtu.
9 noPeerVtuPresent Vtu failure during initialization
due to no activation sequence
detected from peer Vtu.
This is intended to supplement ifOperStatus."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
Sources for this description

OID Repository

View at oid-base.com
Automatically extracted from RFC3728

Description 2

Indicates current state of the Vtu line. This is a
bit-map of possible conditions. The various bit
positions are:

0 noDefect There are no defects on the line.

1 lossOfFraming Vtu failure due to not receiving
a valid frame.

2 lossOfSignal Vtu failure due to not receiving
signal.

3 lossOfPower Vtu failure due to loss of power.

4 lossOfSignalQuality Loss of Signal Quality is declared
when the Noise Margin falls below
the Minimum Noise Margin, or the
bit-error-rate exceeds 10^-7.

5 lossOfLink Vtu failure due to inability to
link with peer Vtu. Set whenever
the transceiver is in the 'Warm
Start' state.

6 dataInitFailure Vtu failure during initialization
due to bit errors corrupting
startup exchange data.




7 configInitFailure Vtu failure during initialization
due to peer Vtu not able to
support requested configuration.

8 protocolInitFailure Vtu failure during initialization
due to incompatible protocol used
by the peer Vtu.

9 noPeerVtuPresent Vtu failure during initialization
due to no activation sequence
detected from peer Vtu.

This is intended to supplement ifOperStatus.
Sources for this description

Circitor

Parsed from VDSL-LINE-MIB.mib · VDSL-LINE-MIB

Source file: Download VDSL-LINE-MIB.txt · Publisher's file

Vendor MIB copy from the Netdisco archive.

Source file: Download VDSL-LINE-MIB · Publisher's file

Vendor MIB copy from the LibreNMS archive.

Source file: Download VDSL-LINE-MIB · Publisher's file

Vendor MIB copy from the Observium Community archive.

Related source files and packages:

Source file: Download RFC 3728 · Publisher's file · RFC errata

Source file: Download VDSL-LINE-MIB.mib

Browse all files from Circitor

Historical records

Additional source information

Information from MIBdepot
vdslPhysCurrStatus OBJECT-TYPE
       SYNTAX       BITS
           {
           noDefect(0),
           lossOfFraming(1),
           lossOfSignal(2),
           lossOfPower(3),
           lossOfSignalQuality(4),
           lossOfLink(5),
           dataInitFailure(6),
           configInitFailure(7),
           protocolInitFailure(8),
           noPeerVtuPresent(9)
           }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "Indicates current state of the Vtu line.  This is a
           bit-map of possible conditions.  The various bit
           positions are:

           0   noDefect             There are no defects on the line.

           1   lossOfFraming        Vtu failure due to not receiving
                                    a valid frame.

           2   lossOfSignal         Vtu failure due to not receiving
                                    signal.

           3   lossOfPower          Vtu failure due to loss of power.

           4   lossOfSignalQuality  Loss of Signal Quality is declared
                                    when the Noise Margin falls below
                                    the Minimum Noise Margin, or the
                                    bit-error-rate exceeds 10^-7.

           5   lossOfLink           Vtu failure due to inability to
                                    link with peer Vtu.  Set whenever
                                    the transceiver is in the 'Warm
                                    Start' state.

           6   dataInitFailure      Vtu failure during initialization
                                    due to bit errors corrupting
                                    startup exchange data.

           7   configInitFailure    Vtu failure during initialization
                                    due to peer Vtu not able to
                                    support requested configuration.

           8   protocolInitFailure  Vtu failure during initialization
                                    due to incompatible protocol used
                                    by the peer Vtu.

           9   noPeerVtuPresent     Vtu failure during initialization
                                    due to no activation sequence
                                    detected from peer Vtu.

           This is intended to supplement ifOperStatus."
       REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
        ::= { vdslPhysEntry 7 }
Information from Circitor
vdslPhysCurrStatus OBJECT-TYPE
    SYNTAX       BITS
        {
        noDefect(0),
        lossOfFraming(1),
        lossOfSignal(2),
        lossOfPower(3),
        lossOfSignalQuality(4),
        lossOfLink(5),
        dataInitFailure(6),
        configInitFailure(7),
        protocolInitFailure(8),
        noPeerVtuPresent(9)
        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Indicates current state of the Vtu line.  This is a
        bit-map of possible conditions.  The various bit
        positions are:

        0   noDefect             There are no defects on the line.

        1   lossOfFraming        Vtu failure due to not receiving
                                 a valid frame.

        2   lossOfSignal         Vtu failure due to not receiving
                                 signal.

        3   lossOfPower          Vtu failure due to loss of power.

        4   lossOfSignalQuality  Loss of Signal Quality is declared
                                 when the Noise Margin falls below
                                 the Minimum Noise Margin, or the
                                 bit-error-rate exceeds 10^-7.

        5   lossOfLink           Vtu failure due to inability to
                                 link with peer Vtu.  Set whenever
                                 the transceiver is in the 'Warm
                                 Start' state.

        6   dataInitFailure      Vtu failure during initialization
                                 due to bit errors corrupting
                                 startup exchange data.




        7   configInitFailure    Vtu failure during initialization
                                 due to peer Vtu not able to
                                 support requested configuration.

        8   protocolInitFailure  Vtu failure during initialization
                                 due to incompatible protocol used
                                 by the peer Vtu.

        9   noPeerVtuPresent     Vtu failure during initialization
                                 due to no activation sequence
                                 detected from peer Vtu.

        This is intended to supplement ifOperStatus."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
     ::= { vdslPhysEntry 7 }

Registration

Registration authorities

First Registration Authority (inferred from ancestor 1.3.6)

Defense Communication Agency

Current Registration Authority (inferred from ancestor 1.3.6.1.2)

Internet Assigned Numbers Authority

Siblings (9)

OIDNameDirect childrenDescendantsDescription
1.3.6.1.2.1.10.97.1.1.2.1.1 vdslPhysSide00 Identifies whether the transceiver is the Vtuc or Vtur.
1.3.6.1.2.1.10.97.1.1.2.1.2 vdslPhysInvSerialNumber00 The vendor specific string that identifies the



vendor equipment.
1.3.6.1.2.1.10.97.1.1.2.1.3 vdslPhysInvVendorID00 The vendor ID code is a copy of the binary vendor
identification field expressed as readable characters
in hexadecimal notation.
1.3.6.1.2.1.10.97.1.1.2.1.4 vdslPhysInvVersionNumber00 The vendor specific version number sent by this Vtu
as part of the initialization messages. It is a copy
of the binary version n…
1.3.6.1.2.1.10.97.1.1.2.1.5 vdslPhysCurrSnrMgn00 Noise Margin as seen by this Vtu with respect to its
received signal in 0.25dB. The effective range is
-31.75 to +31.75 dB.
1.3.6.1.2.1.10.97.1.1.2.1.6 vdslPhysCurrAtn00 Measured difference in the total power transmitted by
the peer Vtu and the total power received by this Vtu.
The effective range …
1.3.6.1.2.1.10.97.1.1.2.1.8 vdslPhysCurrOutputPwr00 Measured total output power transmitted by this VTU.
This is the measurement that was reported during
the last activation sequenc…
1.3.6.1.2.1.10.97.1.1.2.1.9 vdslPhysCurrAttainableRate00 Indicates the maximum currently attainable data rate
in steps of 1000 bits/second by the Vtu. This value
will be equal to or gre…
1.3.6.1.2.1.10.97.1.1.2.1.10 vdslPhysCurrLineRate00 Indicates the current data rate in steps of 1000
bits/second by the Vtu. This value will be less than
or equal to vdslPhysCurrAt…