This object indicates the format of the layer 3
protocol ID in the Ethernet packet. A value of
none(0) means that the rule does not use the
layer 3 protocol type as a matching criteria.
A value of ethertype(1) means that the rule
applies only to frames that contain an
EtherType value. Ethertype values are contained
in packets using the Dec-Intel-Xerox (DIX)
encapsulation or the RFC1042 Sub-Network Access
Protocol (SNAP) encapsulation formats.
A value of dsap(2) means that the rule applies
only to frames using the IEEE802.3
encapsulation format with a Destination Service
Access Point (DSAP) other
than 0xAA (which is reserved for SNAP).
A value of mac(3) means that the rule applies
only to MAC management messages for MAC management
messages.
A value of all(4) means that the rule matches
all Ethernet packets.
If the Ethernet frame contains an 802.1P/Q Tag
header (i.e., EtherType 0x8100), this object
applies to the embedded EtherType field within
the 802.1P/Q header.
If the referenced parameter is not present in a
classifier, this object reports the value of 0.
Parsed from file DOCS-IETF-QOS-MIB.mib
Module: DOCS-IETF-QOS-MIB
This object indicates the format of the layer 3
protocol ID in the Ethernet packet. A value of
none(0) means that the rule does not use the
layer 3 protocol type as a matching criteria.
A value of ethertype(1) means that the rule
applies only to frames that contain an
EtherType value. Ethertype values are contained
in packets using the Dec-Intel-Xerox (DIX)
encapsulation or the RFC1042 Sub-Network Access
Protocol (SNAP) encapsulation formats.
A value of dsap(2) means that the rule applies
only to frames using the IEEE802.3
encapsulation format with a Destination Service
Access Point (DSAP) other
than 0xAA (which is reserved for SNAP).
A value of mac(3) means that the rule applies
only to MAC management messages for MAC management
messages.
A value of all(4) means that the rule matches
all Ethernet packets.
If the Ethernet frame contains an 802.1P/Q Tag
header (i.e., EtherType 0x8100), this object
applies to the embedded EtherType field within
the 802.1P/Q header.
If the referenced parameter is not present in a
classifier, this object reports the value of 0.
This object indicates the format of the layer 3
protocol ID in the Ethernet packet. A value of
none(0) means that the rule does not use the
layer 3 protocol type as a matching criteria.
A value of ethertype(1) means that the rule
applies only to frames that contain an
EtherType value. Ethertype values are contained
in packets using the Dec-Intel-Xerox (DIX)
encapsulation or the RFC1042 Sub-Network Access
Protocol (SNAP) encapsulation formats.
A value of dsap(2) means that the rule applies
only to frames using the IEEE802.3
encapsulation format with a Destination Service
Access Point (DSAP) other
than 0xAA (which is reserved for SNAP).
A value of mac(3) means that the rule applies
only to MAC management messages for MAC management
messages.
A value of all(4) means that the rule matches
all Ethernet packets.
If the Ethernet frame contains an 802.1P/Q Tag
header (i.e., EtherType 0x8100), this object
applies to the embedded EtherType field within
the 802.1P/Q header.
If the referenced parameter is not present in a
classifier, this object reports the value of 0.
Parsed from file rfc4323-IPCDN-DOCSIS-QoS.mib.txt
Company: None
Module: DOCS-IETF-QOS-MIB
This object indicates the format of the layer 3
protocol ID in the Ethernet packet. A value of
none(0) means that the rule does not use the
layer 3 protocol type as a matching criteria.
A value of ethertype(1) means that the rule
applies only to frames that contain an
EtherType value. Ethertype values are contained
in packets using the Dec-Intel-Xerox (DIX)
encapsulation or the RFC1042 Sub-Network Access
Protocol (SNAP) encapsulation formats.
A value of dsap(2) means that the rule applies
only to frames using the IEEE802.3
encapsulation format with a Destination Service
Access Point (DSAP) other
than 0xAA (which is reserved for SNAP).
A value of mac(3) means that the rule applies
only to MAC management messages for MAC management
messages.
A value of all(4) means that the rule matches
all Ethernet packets.
If the Ethernet frame contains an 802.1P/Q Tag
header (i.e., EtherType 0x8100), this object
applies to the embedded EtherType field within
the 802.1P/Q header.
If the referenced parameter is not present in a
classifier, this object reports the value of 0.
docsIetfQosPktClassEnetProtocolType OBJECT-TYPE SYNTAX INTEGER { none(0), ethertype(1), dsap(2), mac(3), all(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the format of the layer 3 protocol ID in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames that contain an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of mac(3) means that the rule applies only to MAC management messages for MAC management messages. A value of all(4) means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e., EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv2.0-I06-040804, Appendix C.2.1.6.3" ::= { docsIetfQosPktClassEntry 20 }
docsIetfQosPktClassEnetProtocolType OBJECT-TYPE SYNTAX INTEGER { none(0), ethertype(1), dsap(2), mac(3), all(4) } ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the format of the layer 3 protocol ID in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames that contain an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of mac(3) means that the rule applies only to MAC management messages for MAC management messages. A value of all(4) means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e., EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv2.0-I06-040804, Appendix C.2.1.6.3" ::= { docsIetfQosPktClassEntry 20 }
Vendor: Cisco Systems
Module: DOCS-IETF-QOS-MIB (DOCS-IETF-QOS-MIB-V1SMI.my)
Type: TABULAR
Access: read-only
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
docsIetfQosPktClassEnetProtocolType OBJECT-TYPE SYNTAX INTEGER { none(0), ethertype(1), dsap(2), mac(3), all(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the format of the layer 3 protocol ID in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames that contain an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of mac(3) means that the rule applies only to MAC management messages for MAC management messages. A value of all(4) means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e., EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv2.0-I06-040804, Appendix C.2.1.6.3" ::= { docsIetfQosPktClassEntry 20 }
docsIetfQosPktClassEnetProtocolType OBJECT-TYPE SYNTAX INTEGER { none(0), ethertype(1), dsap(2), mac(3), all(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the format of the layer 3 protocol ID in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames that contain an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of mac(3) means that the rule applies only to MAC management messages for MAC management messages. A value of all(4) means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e., EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv2.0-I06-040804, Appendix C.2.1.6.3" ::= { docsIetfQosPktClassEntry 20 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.127.1.1.1.1 | docsIetfQosPktClassId | 0 | 0 | Index assigned to packet classifier entry by the CMTS, which is unique per Service Flow. |
| 1.3.6.1.2.1.127.1.1.1.2 | docsIetfQosPktClassDirection | 0 | 0 | Indicates the direction to which the classifier is applied. |
| 1.3.6.1.2.1.127.1.1.1.3 | docsIetfQosPktClassPriority | 0 | 0 | The value specifies the order of evaluation of the classifiers. The higher the value, the higher the priority. The value of 0 is u… |
| 1.3.6.1.2.1.127.1.1.1.4 | docsIetfQosPktClassIpTosLow | 0 | 0 | The low value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the … |
| 1.3.6.1.2.1.127.1.1.1.5 | docsIetfQosPktClassIpTosHigh | 0 | 0 | The 8-bit high value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object report… |
| 1.3.6.1.2.1.127.1.1.1.6 | docsIetfQosPktClassIpTosMask | 0 | 0 | The mask value is bitwise ANDed with TOS byte in an IP packet, and this value is used for range checking of TosLow and TosHigh. If… |
| 1.3.6.1.2.1.127.1.1.1.7 | docsIetfQosPktClassIpProtocol | 0 | 0 | This object indicates the value of the IP Protocol field required for IP packets to match this rule. The value 256 matches traffic… |
| 1.3.6.1.2.1.127.1.1.1.8 | docsIetfQosPktClassInetAddressType | 0 | 0 | The type of the Internet address for docsIetfQosPktClassInetSourceAddr, docsIetfQosPktClassInetSourceMask, docsIetfQosPktClassInet… |
| 1.3.6.1.2.1.127.1.1.1.9 | docsIetfQosPktClassInetSourceAddr | 0 | 0 | This object specifies the value of the IP Source Address required for packets to match this rule. An IP packet matches the rule wh… |
| 1.3.6.1.2.1.127.1.1.1.10 | docsIetfQosPktClassInetSourceMask | 0 | 0 | This object specifies which bits of a packet's IP Source Address are compared to match this rule. An IP packet matches the rule wh… |
| 1.3.6.1.2.1.127.1.1.1.11 | docsIetfQosPktClassInetDestAddr | 0 | 0 | This object specifies the value of the IP Destination Address required for packets to match this rule. An IP packet matches the ru… |
| 1.3.6.1.2.1.127.1.1.1.12 | docsIetfQosPktClassInetDestMask | 0 | 0 | This object specifies which bits of a packet's IP Destination Address are compared to match this rule. An IP packet matches the ru… |
| 1.3.6.1.2.1.127.1.1.1.13 | docsIetfQosPktClassSourcePortStart | 0 | 0 | This object specifies the low-end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is i… |
| 1.3.6.1.2.1.127.1.1.1.14 | docsIetfQosPktClassSourcePortEnd | 0 | 0 | This object specifies the high-end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is … |
| 1.3.6.1.2.1.127.1.1.1.15 | docsIetfQosPktClassDestPortStart | 0 | 0 | This object specifies the low-end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the refere… |
| 1.3.6.1.2.1.127.1.1.1.16 | docsIetfQosPktClassDestPortEnd | 0 | 0 | This object specifies the high-end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the refer… |
| 1.3.6.1.2.1.127.1.1.1.17 | docsIetfQosPktClassDestMacAddr | 0 | 0 | An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with docsIetfQosPktClassDestMacMask equals the… |
| 1.3.6.1.2.1.127.1.1.1.18 | docsIetfQosPktClassDestMacMask | 0 | 0 | An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with docsIetfQosPktClassDestMacMask equals the… |
| 1.3.6.1.2.1.127.1.1.1.19 | docsIetfQosPktClassSourceMacAddr | 0 | 0 | An Ethernet packet matches this entry when its source MAC address equals the value of this object. If the referenced parameter is … |
| 1.3.6.1.2.1.127.1.1.1.21 | docsIetfQosPktClassEnetProtocol | 0 | 0 | If docsIetfQosEthPktClassProtocolType is none(0), this object is ignored when considering whether a packet matches the current ru… |
| 1.3.6.1.2.1.127.1.1.1.22 | docsIetfQosPktClassUserPriLow | 0 | 0 | This object applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include… |
| 1.3.6.1.2.1.127.1.1.1.23 | docsIetfQosPktClassUserPriHigh | 0 | 0 | This object applies only to Ethernet frames using the 802.1P/Qtag header (indicated with EtherType 0x8100). Such frames include … |
| 1.3.6.1.2.1.127.1.1.1.24 | docsIetfQosPktClassVlanId | 0 | 0 | This object applies only to Ethernet frames using the 802.1P/Q tag header. Tagged packets must have a VLAN Identifier that matches… |
| 1.3.6.1.2.1.127.1.1.1.25 | docsIetfQosPktClassStateActive | 0 | 0 | This object indicates whether or not the classifier is enabled to classify packets to a Service Flow. If the referenced parameter… |
| 1.3.6.1.2.1.127.1.1.1.26 | docsIetfQosPktClassPkts | 0 | 0 | This object counts the number of packets that have been classified using this entry. This includes all packets delivered to a Se… |
| 1.3.6.1.2.1.127.1.1.1.27 | docsIetfQosPktClassBitMap | 0 | 0 | This object indicates which parameter encodings were actually present in the DOCSIS packet classifier encoding signaled in the DO… |