mdmCCConnectionFailReason OBJECT-TYPE
SYNTAX INTEGER {
-- General
unknown(1),
other(2),
managementCommand(3),
inactivityTimeout(4),
mnpIncompatibility(5),
protocolError(6),
-- DCE
powerLoss(10),
equipmentFailure(11),
-- DTE Interface
dtrDrop(20),
-- Line Interface
noDialTone(30),
lineBusy(31),
noAnswer(32),
voiceDetected(33),
-- Signal Converter
carrierLost(40),
trainingFailed(41),
faxDetected(42)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the reason that the last connection or attempt
failed. The meaning of each reason code is explained below.
unknown:
This code means the failure reason is unknown or
there has been no previous call.
other:
This code used when no other code is applicable.
Additional vendor information may be available
elsewhere.
managementCommand:
A management command terminated the call. These
commands include escaping to command mode, initiating
dialing, restoring lines, and disconnecting.
inactivityTimeout:
The call was terminated because it was inactive for
at the minimum duration specified.
mnpIncompatibility:
The modems are unable to resolve MNP protocol
differences.
protocolError:
An error occured in one of protocol in use. Further
information is required to determine in which
protocol the error occurred, and the exact nature of
the error.
powerLoss:
The modem lost power and disconnected the call.
equipmentFailure:
The modem equipment failed.
dtrDrop:
DTR has been turned off while the modem is to
disconnect on DTR drop. (Ref: V.58 cct108TurnedOff)
noDialTone:
If the modem is to monitor for call progress tones,
but the modem has failed to detect dial tone while
attempting to dial a number.
lineBusy:
Busy signal is detected while busy signal detection
is enabled, or while the W or @ dial modifier is
used. (Ref: V.58 engagedTone)
noAnswer:
The call was not answered.
voiceDetected:
A voice was detected on the call.
carrierLost:
Indicates that the modem has disconnected due to
detection of loss of carrier. In TIA-602, the S10
register determines the time that loss of carrier
must be detected before the modem disconnects.
trainingFailed:
Indicates that the modems did not successfully train
and reach data mode on the previous connection.
faxDetected:
A fax was detected on the call."
REFERENCE "V.58 callCleared"
View at oid-info.com
Indicates the reason that the last connection or attempt
failed. The meaning of each reason code is explained below.
unknown:
This code means the failure reason is unknown or
there has been no previous call.
other:
This code used when no other code is applicable.
Additional vendor information may be available
elsewhere.
managementCommand:
A management command terminated the call. These
commands include escaping to command mode, initiating
dialing, restoring lines, and disconnecting.
inactivityTimeout:
The call was terminated because it was inactive for
at the minimum duration specified.
mnpIncompatibility:
The modems are unable to resolve MNP protocol
differences.
protocolError:
An error occured in one of protocol in use. Further
information is required to determine in which
protocol the error occurred, and the exact nature of
the error.
powerLoss:
The modem lost power and disconnected the call.
equipmentFailure:
The modem equipment failed.
dtrDrop:
DTR has been turned off while the modem is to
disconnect on DTR drop. (Ref: V.58 cct108TurnedOff)
noDialTone:
If the modem is to monitor for call progress tones,
but the modem has failed to detect dial tone while
attempting to dial a number.
lineBusy:
Busy signal is detected while busy signal detection
is enabled, or while the 'W' or '@' dial modifier is
used. (Ref: V.58 engagedTone)
noAnswer:
The call was not answered.
voiceDetected:
A voice was detected on the call.
carrierLost:
Indicates that the modem has disconnected due to
detection of loss of carrier. In TIA-602, the S10
register determines the time that loss of carrier
must be detected before the modem disconnects.
trainingFailed:
Indicates that the modems did not successfully train
and reach data mode on the previous connection.
faxDetected:
A fax was detected on the call.
Parsed from file rfc1696.mib.txt
Company: lucent
Module: Modem-MIB
Automatically extracted from RFC1696
mdmCCConnectionFailReason OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), managementCommand(3), inactivityTimeout(4), mnpIncompatibility(5), protocolError(6), powerLoss(10), equipmentFailure(11), dtrDrop(20), noDialTone(30), lineBusy(31), noAnswer(32), voiceDetected(33), carrierLost(40), trainingFailed(41), faxDetected(42) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the reason that the last connection or attempt failed. The meaning of each reason code is explained below. unknown: This code means the failure reason is unknown or there has been no previous call. other: This code used when no other code is applicable. Additional vendor information may be available elsewhere. managementCommand: A management command terminated the call. These commands include escaping to command mode, initiating dialing, restoring lines, and disconnecting. inactivityTimeout: The call was terminated because it was inactive for at the minimum duration specified. mnpIncompatibility: The modems are unable to resolve MNP protocol differences. protocolError: An error occured in one of protocol in use. Further information is required to determine in which protocol the error occurred, and the exact nature of the error. powerLoss: The modem lost power and disconnected the call. equipmentFailure: The modem equipment failed. dtrDrop: DTR has been turned off while the modem is to disconnect on DTR drop. (Ref: V.58 cct108TurnedOff) noDialTone: If the modem is to monitor for call progress tones, but the modem has failed to detect dial tone while attempting to dial a number. lineBusy: Busy signal is detected while busy signal detection is enabled, or while the 'W' or '@' dial modifier is used. (Ref: V.58 engagedTone) noAnswer: The call was not answered. voiceDetected: A voice was detected on the call. carrierLost: Indicates that the modem has disconnected due to detection of loss of carrier. In TIA-602, the S10 register determines the time that loss of carrier must be detected before the modem disconnects. trainingFailed: Indicates that the modems did not successfully train and reach data mode on the previous connection. faxDetected: A fax was detected on the call." REFERENCE "V.58 callCleared" ::= { mdmCallControlEntry 6 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.38.1.7.1.1 | mdmCCRingsBeforeAnswer | 0 | 0 | Determines which ring the modem will wait to answer the phone on. If this value is `0', the modem will not go offhook and answer… |
| 1.3.6.1.2.1.38.1.7.1.2 | mdmCCCallSetUpFailTimer | 0 | 0 | This parameter specifies the amount of time, in seconds, that the modem shall allow between either answering a call (automaticall… |
| 1.3.6.1.2.1.38.1.7.1.3 | mdmCCResultCodeEnable | 0 | 0 | When disabled, the DCE shall issue no 'result codes' of any kind to the DTE either in response to unsolicited events (eg. ring si… |
| 1.3.6.1.2.1.38.1.7.1.4 | mdmCCEscapeAction | 0 | 0 | The modem's action upon successfully recognizing the 'escape to command mode' character sequence. |
| 1.3.6.1.2.1.38.1.7.1.5 | mdmCCCallDuration | 0 | 0 | Present or last completed connection time in seconds. If there have been no previous connections, this value should be -1. |