This object specifies the delay by which the CTS
signal will transition following a transition in
the RTS signal. The value of this object represents
the number of 10 millisecond increments to delay
before transitioning.
Parsed from file act.mib.txt
Company: cai
Module: ACT-FP-CHANNEL
Vendor: Computer Associates
Module: ACT-CONSTANTS (act.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
(
0..100 )
Automatically extracted from www.mibdepot.com
actFpChannelCTSdelay OBJECT-TYPE SYNTAX INTEGER(0..100) ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the delay by which the CTS signal will transition following a transition in the RTS signal. The value of this object represents the number of 10 millisecond increments to delay before transitioning." ::= { actFpChannelEntry 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.1 | actFpChannelIndex | 0 | 0 | This object represents the unique identifier for a row in the channel table. The value of this object corresponds to an ifIndex … |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.2 | actFpChannelType | 0 | 0 | This object specifies the type of channel (interface, port). The value of this object indicates which set of tables contain addi… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.3 | actFpChannelRate | 0 | 0 | The value of this object represents the rate of the channel. The value this object may assume is dependent upon (a) the type of … |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.4 | actFpChannelStatus | 0 | 0 | This object identifies the current state of the channel. The values and their respective meanings are: disabled - this channel i… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.5 | actFpChannelCTS | 0 | 0 | This object specifies the behavior of the CTS signal. forcedOff(1) means that CTS is always off, forcedOn(2) means that CTS is al… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.7 | actFpChannelDSR | 0 | 0 | This object specifies the behavior of the DSR signal. forcedOff(1) means that DSR is always off, forcedOn(2) means that DSR is al… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.8 | actFpChannelDCD | 0 | 0 | This object specifies the behavior of the DCD (Data Carrier Detect) signal. The value forcedOff(1) means that DCD is always off, … |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.9 | actFpChannelDestinationDlci | 0 | 0 | This object specifies the Frame Relay DLCI that is the logical 'other end' of this channel. |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.10 | actFpChannelDestinationSlot | 0 | 0 | This object indicates one component of the destination address for this channel. In conjunction with the DLCI and the destinatio… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.11 | actFpChannelDestinationChannel | 0 | 0 | This object represents the final component of the destination address for this channel. In conjunction with the DLCI and the De… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.12 | actFpChannelCallTimer | 0 | 0 | This object represents the amount of time, in seconds, in which a call can be established before the unit determines the call can… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.13 | actFpChannelIncomingCallPolicy | 0 | 0 | This object sets the policy for incoming calls on this channel. The value inhibit(1) states that all incoming calls for this cha… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.14 | actFpChannelOutgoingCallPolicy | 0 | 0 | This object specifies the policy for outgoing calls (connections) on this channel. When this object has the value inhibit(1), th… |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.15 | actFpChannelCallConnectionPolicy | 0 | 0 | This object specifies whether or not bandwidth is to be reserved when a call is established. |
| 1.3.6.1.4.1.1186.2.2.1.3.2.1.1.16 | actFpChannelDiscardEligible | 0 | 0 | This object specifies whether or not to consider outgoing data on this channel is to be considered 'throw-away'. When the value … |