E1 data transfer type is only applicable in
Circuit Emulation where unstructured CE packets
entire T1 frame including the F-bit into the AAL1
for data tranfer, whereas, the structured CE
packets the entire E1 frame except the Frame
alignment signal channel.
Parsed from file ac120.my.V07.00.C00.mib.txt
Company: None
Module: ACMIB
E1 data transfer type is only applicable in
Circuit Emulation where unstructured CE packets
entire T1 frame including the F-bit into the AAL1
for data tranfer, whereas, the structured CE
packets the entire E1 frame except the Frame
alignment signal channel.
Parsed from file ACMIB.mib
Module: ACMIB
Vendor: Lucent Technologies
Module: ACMIB
[Automatically extracted from oidview.com]
e1DataTransferType OBJECT-TYPE SYNTAX INTEGER { structured(1), unstructured(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "E1 data transfer type is only applicable in Circuit Emulation where unstructured CE packets entire T1 frame including the F-bit into the AAL1 for data tranfer, whereas, the structured CE packets the entire E1 frame except the Frame alignment signal channel." DEFVAL { structured } ::= { e1PortConfigEntry 11 }
e1DataTransferType OBJECT-TYPE SYNTAX INTEGER { structured(1), unstructured(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "E1 data transfer type is only applicable in Circuit Emulation where unstructured CE packets entire T1 frame including the F-bit into the AAL1 for data tranfer, whereas, the structured CE packets the entire E1 frame except the Frame alignment signal channel." DEFVAL { structured } ::= { e1PortConfigEntry 11 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1751.2.18.2.12.1.1 | e1PortId | 0 | 0 | interface index - slot/port: SSPP |
| 1.3.6.1.4.1.1751.2.18.2.12.1.2 | e1Channelization | 0 | 0 | e1 interface type |
| 1.3.6.1.4.1.1751.2.18.2.12.1.3 | e1LineType | 0 | 0 | E1 interface type. The rate of E1 is 2.048 Mbps |
| 1.3.6.1.4.1.1751.2.18.2.12.1.4 | e1LineCoding | 0 | 0 | e1 interface type |
| 1.3.6.1.4.1.1751.2.18.2.12.1.5 | e1LoopbackConfig | 0 | 0 | This variable represents the loopback configuration of the e1 interface See above diagrams for explanations of loops. |
| 1.3.6.1.4.1.1751.2.18.2.12.1.6 | e1TransmitClockSource | 0 | 0 | e1 timing source |
| 1.3.6.1.4.1.1751.2.18.2.12.1.7 | e1LineNationalBits | 0 | 0 | e1 line country specific code |
| 1.3.6.1.4.1.1751.2.18.2.12.1.8 | e1LineStatus | 0 | 0 | This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alar… |
| 1.3.6.1.4.1.1751.2.18.2.12.1.10 | e1TS16 | 0 | 0 | Time slot 16 is configurable for channel associated signaling (CAS) or data. cas: 'ABCD' signaling will be extracted in time slot … |
| 1.3.6.1.4.1.1751.2.18.2.12.1.12 | e1CRC4 | 0 | 0 | Enable or disable transmission of CRC4 bits on bit 1 of each frame. |
| 1.3.6.1.4.1.1751.2.18.2.12.1.13 | e1OamInterworkingType | 0 | 0 | Specifies whether the interworking is done by trunk conditioning or unframed1s |
| 1.3.6.1.4.1.1751.2.18.2.12.1.14 | e1EnhanceFeatureSet1 | 0 | 0 | To enable/disable a proprietary ab signaling scheme, it applies to all DS0s in the port. No individual DS0 signaling can be config… |
| 1.3.6.1.4.1.1751.2.18.2.12.1.15 | e1ConnGatewayFeature | 0 | 0 | To enable/disable connection gateway (Sapphire) API. |