Turn KG resync on/off
Parsed from file ac120.my.V07.00.C00.mib.txt
Company: None
Module: ACMIB
Turn KG resync on/off
Parsed from file ACMIB.mib
Module: ACMIB
Vendor: Lucent Technologies
Module: ACMIB
[Automatically extracted from oidview.com]
msKgResync OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turn KG resync on/off" DEFVAL { enabled } ::= { msPortConfigEntry 15 }
msKgResync OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turn KG resync on/off" DEFVAL { enabled } ::= { msPortConfigEntry 15 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1751.2.18.2.4.1.1 | msPortId | 0 | 0 | slot/port: SSPP |
| 1.3.6.1.4.1.1751.2.18.2.4.1.2 | msLineCoding | 0 | 0 | Line Coding. |
| 1.3.6.1.4.1.1751.2.18.2.4.1.3 | msBaudRate | 0 | 0 | baud rate is determined by multiplying this number by the msBaudRateMultiplier |
| 1.3.6.1.4.1.1751.2.18.2.4.1.4 | msProtocol | 0 | 0 | protocol type for serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.5 | msEquipmentType | 0 | 0 | Equipment type |
| 1.3.6.1.4.1.1751.2.18.2.4.1.6 | msRs232XmitMode | 0 | 0 | transmit mode for rs232 DTE/DCE serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.7 | msRs232Parity | 0 | 0 | parity for rs232 DTE/DCE serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.8 | msRs232DataBits | 0 | 0 | data bits for rs232 DTE/DCE serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.9 | msRs232StopBits | 0 | 0 | stop bits for rs232 DTE/DCE serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.10 | msTxDataClkSrcForDte | 0 | 0 | Transmit data clock source for DTE, externalTx in is not valid for rs232. This field is ignored if the local side is DCE. |
| 1.3.6.1.4.1.1751.2.18.2.4.1.11 | msTxDataClkSrcForDce | 0 | 0 | Transmit data clock source for DCE localTiming: a local clock source is used. (e.g., from backplane (stratum) loopTiming: from rem… |
| 1.3.6.1.4.1.1751.2.18.2.4.1.12 | msRxDataClkSrcForDce | 0 | 0 | Receive data clock source for DCE localTiming: a local clock source is used. (e.g., from backplane (stratum) loopTiming: from remo… |
| 1.3.6.1.4.1.1751.2.18.2.4.1.13 | msRxClkPolarity | 0 | 0 | Whether or not to reverse the receive clock |
| 1.3.6.1.4.1.1751.2.18.2.4.1.14 | msTxClkPolarity | 0 | 0 | Whether or not to reverse the transmit clock |
| 1.3.6.1.4.1.1751.2.18.2.4.1.16 | msHandshake | 0 | 0 | Multiserial Module handshake: observed : used with AAL1 to monitor RTS/CTS exchange. |
| 1.3.6.1.4.1.1751.2.18.2.4.1.17 | msSpeedAdaption | 0 | 0 | The state of allowing speed adaption |
| 1.3.6.1.4.1.1751.2.18.2.4.1.18 | msBitStuffing | 0 | 0 | When msBitStuffing is enabled, CAC throughput is (1 + 1/7) user throughtput. Otherwise the CAC throughput is the same as the user… |
| 1.3.6.1.4.1.1751.2.18.2.4.1.19 | msLineStatus | 0 | 0 | line status on the port: The msLineStatus is a bit map representation. It can represent multiple failures (alarms) if supported by… |
| 1.3.6.1.4.1.1751.2.18.2.4.1.20 | msRxDataPolarity | 0 | 0 | Whether or not to reverse the receive data |
| 1.3.6.1.4.1.1751.2.18.2.4.1.21 | msTxDataPolarity | 0 | 0 | Whether or not to reverse the transmit data |
| 1.3.6.1.4.1.1751.2.18.2.4.1.22 | msLoopbackConfig | 0 | 0 | This variable represents the loopback configuration of the Serial port. |
| 1.3.6.1.4.1.1751.2.18.2.4.1.23 | msLOSDetection | 0 | 0 | State of detection of LOS by IO card. LOS detection is always enabled when msBitStuffing is enabled. When the interface is not ci… |