State of detection of LOS by IO card.
LOS detection is always enabled when msBitStuffing is enabled.
When the interface is not circuit emulation, the IO card does not report any LOS.
Parsed from file ac120.my.V07.00.C00.mib.txt
Company: None
Module: ACMIB
State of detection of LOS by IO card.
LOS detection is always enabled when msBitStuffing is enabled.
When the interface is not circuit emulation, the IO card does not report any LOS.
Parsed from file ACMIB.mib
Module: ACMIB
Vendor: Lucent Technologies
Module: ACMIB
[Automatically extracted from oidview.com]
msLOSDetection OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "State of detection of LOS by IO card. LOS detection is always enabled when msBitStuffing is enabled. When the interface is not circuit emulation, the IO card does not report any LOS." DEFVAL { disabled } ::= { msPortConfigEntry 23 }
msLOSDetection OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "State of detection of LOS by IO card. LOS detection is always enabled when msBitStuffing is enabled. When the interface is not circuit emulation, the IO card does not report any LOS." DEFVAL { disabled } ::= { msPortConfigEntry 23 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1751.2.18.2.4.1.1 | msPortId | 0 | 0 | slot/port: SSPP |
| 1.3.6.1.4.1.1751.2.18.2.4.1.2 | msLineCoding | 0 | 0 | Line Coding. |
| 1.3.6.1.4.1.1751.2.18.2.4.1.3 | msBaudRate | 0 | 0 | baud rate is determined by multiplying this number by the msBaudRateMultiplier |
| 1.3.6.1.4.1.1751.2.18.2.4.1.4 | msProtocol | 0 | 0 | protocol type for serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.5 | msEquipmentType | 0 | 0 | Equipment type |
| 1.3.6.1.4.1.1751.2.18.2.4.1.6 | msRs232XmitMode | 0 | 0 | transmit mode for rs232 DTE/DCE serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.7 | msRs232Parity | 0 | 0 | parity for rs232 DTE/DCE serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.8 | msRs232DataBits | 0 | 0 | data bits for rs232 DTE/DCE serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.9 | msRs232StopBits | 0 | 0 | stop bits for rs232 DTE/DCE serial port |
| 1.3.6.1.4.1.1751.2.18.2.4.1.10 | msTxDataClkSrcForDte | 0 | 0 | Transmit data clock source for DTE, externalTx in is not valid for rs232. This field is ignored if the local side is DCE. |
| 1.3.6.1.4.1.1751.2.18.2.4.1.11 | msTxDataClkSrcForDce | 0 | 0 | Transmit data clock source for DCE localTiming: a local clock source is used. (e.g., from backplane (stratum) loopTiming: from rem… |
| 1.3.6.1.4.1.1751.2.18.2.4.1.12 | msRxDataClkSrcForDce | 0 | 0 | Receive data clock source for DCE localTiming: a local clock source is used. (e.g., from backplane (stratum) loopTiming: from remo… |
| 1.3.6.1.4.1.1751.2.18.2.4.1.13 | msRxClkPolarity | 0 | 0 | Whether or not to reverse the receive clock |
| 1.3.6.1.4.1.1751.2.18.2.4.1.14 | msTxClkPolarity | 0 | 0 | Whether or not to reverse the transmit clock |
| 1.3.6.1.4.1.1751.2.18.2.4.1.15 | msKgResync | 0 | 0 | Turn KG resync on/off |
| 1.3.6.1.4.1.1751.2.18.2.4.1.16 | msHandshake | 0 | 0 | Multiserial Module handshake: observed : used with AAL1 to monitor RTS/CTS exchange. |
| 1.3.6.1.4.1.1751.2.18.2.4.1.17 | msSpeedAdaption | 0 | 0 | The state of allowing speed adaption |
| 1.3.6.1.4.1.1751.2.18.2.4.1.18 | msBitStuffing | 0 | 0 | When msBitStuffing is enabled, CAC throughput is (1 + 1/7) user throughtput. Otherwise the CAC throughput is the same as the user… |
| 1.3.6.1.4.1.1751.2.18.2.4.1.19 | msLineStatus | 0 | 0 | line status on the port: The msLineStatus is a bit map representation. It can represent multiple failures (alarms) if supported by… |
| 1.3.6.1.4.1.1751.2.18.2.4.1.20 | msRxDataPolarity | 0 | 0 | Whether or not to reverse the receive data |
| 1.3.6.1.4.1.1751.2.18.2.4.1.21 | msTxDataPolarity | 0 | 0 | Whether or not to reverse the transmit data |
| 1.3.6.1.4.1.1751.2.18.2.4.1.22 | msLoopbackConfig | 0 | 0 | This variable represents the loopback configuration of the Serial port. |