Reference record for OID 1.3.6.1.4.1.318.1.1.1.11.2.15

upsAdvStateGalaxyVseriesSpecificFault

Status in source: optional.

Names: upsAdvStateGalaxyVseriesSpecificFault

{
  "smi_kind": "OBJECT-TYPE",
  "definition": [
    "upsAdvStateGalaxyVseriesSpecificFault",
    "OBJECT-TYPE",
    "SYNTAX",
    "DisplayString",
    "ACCESS",
    "read-only",
    "STATUS",
    "optional",
    "DESCRIPTION",
    "\"An ASCII string containing 32 flags representing current active faults on a Galaxy V series UPS. The upsAdvStateAbnormalConditions OID shall be used to report active faults as per its description. Additional fault information shall be provided through the upsAdvStateGalaxyVseriesSpecificFault OID. If the Network Card is unable to determine the values of the flags, this variable is set to 'UNKNOWN'. If this variable is not supported by the connected UPS, this variable is set to 'NOT SUPPORTED'. The flags are numbered from 1 to 32, and read from left to right. The flags are defined as follows: Flag 1: Input voltage is out of tolerance Flag 2: Input frequency is out of tolerance Flag 3: External sync frequency is out of tolerance Flag 4: Output frequency is out of tolerance Flag 5: The static bypass switch needs a technical check but is still fully operational Flag 6: Static bypass switch is inoperable. UPS is prevented from going into static bypass operation Flag 7: PBUS cable 1 may be damaged Flag 8: PBUS cable 2 may be damaged Flag 9: The parallel system is not configured correctly or is not working correctly Flag 10: The UC in the controller box is not working correctly Flag 11: Power module surveillance detected a fault Flag 12: The SLC in the controller box is not working correctly Flag 13: No SBS present Flag 14: No power module(s) present Flag 15: Controller box disabled Flag 16: Display communication lost - disconnected Flag 17: The energy storage surveillance has detected a battery temperature above shutdown limit Flag 18: Modular battery cabinet fuse blown Flag 19: Battery module temperature sensor not working correctly Flag 20: The energy storage surveillance has detected a battery discharge current above shutdown limit Flag 21: Ground fault detected Flag 22: External energy storage monitoring: Minor alarm Flag 23: External energy storage monitoring: Major alarm Flag 24: Temperature of input and/or output transformer is too high Flag 25: Parallel breaker status inconsistency detected Flag 26: UC communication lost - disconnected Flag 27: PMC communication lost - disconnected Flag 28: NMC communication lost - disconnected Flag 29: BMC communication lost - disconnected Flag 30: <Reserved> Flag 31: <Reserved> Flag 32: <Reserved>\"",
    "::=",
    "{",
    "upsAdvState",
    "15",
    "}"
  ],
  "syntax_tree": [
    [
      "row",
      "DisplayString"
    ],
    null,
    [
      "MaxAccessPart",
      "read-only"
    ],
    [
      "Status",
      "optional"
    ],
    [
      "DESCRIPTION",
      "An ASCII string containing 32 flags representing current active faults on a Galaxy V series UPS. The upsAdvStateAbnormalConditions OID shall be used to report active faults as per its description. Additional fault information shall be provided through the upsAdvStateGalaxyVseriesSpecificFault OID. If the Network Card is unable to determine the values of the flags, this variable is set to 'UNKNOWN'. If this variable is not supported by the connected UPS, this variable is set to 'NOT SUPPORTED'. The flags are numbered from 1 to 32, and read from left to right. The flags are defined as follows: Flag 1: Input voltage is out of tolerance Flag 2: Input frequency is out of tolerance Flag 3: External sync frequency is out of tolerance Flag 4: Output frequency is out of tolerance Flag 5: The static bypass switch needs a technical check but is still fully operational Flag 6: Static bypass switch is inoperable. UPS is prevented from going into static bypass operation Flag 7: PBUS cable 1 may be damaged Flag 8: PBUS cable 2 may be damaged Flag 9: The parallel system is not configured correctly or is not working correctly Flag 10: The UC in the controller box is not working correctly Flag 11: Power module surveillance detected a fault Flag 12: The SLC in the controller box is not working correctly Flag 13: No SBS present Flag 14: No power module(s) present Flag 15: Controller box disabled Flag 16: Display communication lost - disconnected Flag 17: The energy storage surveillance has detected a battery temperature above shutdown limit Flag 18: Modular battery cabinet fuse blown Flag 19: Battery module temperature sensor not working correctly Flag 20: The energy storage surveillance has detected a battery discharge current above shutdown limit Flag 21: Ground fault detected Flag 22: External energy storage monitoring: Minor alarm Flag 23: External energy storage monitoring: Major alarm Flag 24: Temperature of input and/or output transformer is too high Flag 25: Parallel breaker status inconsistency detected Flag 26: UC communication lost - disconnected Flag 27: PMC communication lost - disconnected Flag 28: NMC communication lost - disconnected Flag 29: BMC communication lost - disconnected Flag 30: <Reserved> Flag 31: <Reserved> Flag 32: <Reserved>"
    ],
    null,
    null,
    null,
    null
  ]
}

• Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community) · Publisher's source file: PowerNet-MIB

  Vendor MIB copy from the LibreNMS archive.

  Module: PowerNet-MIB

  Published definition

  upsAdvStateGalaxyVseriesSpecificFault OBJECT-TYPE
     SYNTAX DisplayString
     ACCESS read-only
     STATUS optional
     DESCRIPTION
          "An ASCII string containing 32 flags representing
          current active faults on a Galaxy V series UPS.
          The upsAdvStateAbnormalConditions OID shall be used to report
          active faults as per its description. Additional fault information
          shall be provided through the upsAdvStateGalaxyVseriesSpecificFault OID.
          If the Network Card is unable to determine the values of the flags, this
          variable is set to 'UNKNOWN'. If this variable is not
          supported by the connected UPS, this variable is set to
          'NOT SUPPORTED'.
  
          The flags are numbered from 1 to 32, and read from left to
          right. The flags are defined as follows:
  
          Flag  1: Input voltage is out of tolerance
          Flag  2: Input frequency is out of tolerance
          Flag  3: External sync frequency is out of tolerance
          Flag  4: Output frequency is out of tolerance
  
          Flag  5: The static bypass switch needs a technical check but is still fully operational
          Flag  6: Static bypass switch is inoperable. UPS is prevented from going into static bypass operation
          Flag  7: PBUS cable 1 may be damaged
          Flag  8: PBUS cable 2 may be damaged
  
          Flag  9: The parallel system is not configured correctly or is not working correctly
          Flag 10: The UC in the controller box is not working correctly
          Flag 11: Power module surveillance detected a fault
          Flag 12: The SLC in the controller box is not working correctly
  
          Flag 13: No SBS present
          Flag 14: No power module(s) present
          Flag 15: Controller box disabled
          Flag 16: Display communication lost - disconnected
  
          Flag 17: The energy storage surveillance has detected a battery temperature above shutdown limit
          Flag 18: Modular battery cabinet fuse blown
          Flag 19: Battery module temperature sensor not working correctly
          Flag 20: The energy storage surveillance has detected a battery discharge current above shutdown limit
  
          Flag 21: Ground fault detected
          Flag 22: External energy storage monitoring: Minor alarm
          Flag 23: External energy storage monitoring: Major alarm
          Flag 24: Temperature of input and/or output transformer is too high
  
          Flag 25: Parallel breaker status inconsistency detected
          Flag 26: UC communication lost - disconnected
          Flag 27: PMC communication lost - disconnected
          Flag 28: NMC communication lost - disconnected
  
          Flag 29: BMC communication lost - disconnected
          Flag 30: <Reserved>
          Flag 31: <Reserved>
          Flag 32: <Reserved>"
     ::= { upsAdvState 15 }

  Module imports

  {'RFC-1212': ['OBJECT-TYPE'], 'RFC-1215': ['TRAP-TYPE'], 'RFC1155-SMI': ['enterprises', 'IpAddress', 'Gauge', 'TimeTicks'], 'RFC1213-MIB': ['DisplayString'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}

  Related source files and packages:

  • LibreNMS original distribution archiveFile: librenms/librenms/tar.gz/…; 80.2 MiB
  • Archive revision metadata: librenms/librenms (JSON)File: repos/librenms/librenms/commits/master; 36,945 bytes
  
  Source location: PowerNet-MIB::upsAdvStateGalaxyVseriesSpecificFault.
  Source version and references

  Downloaded: 2026-10-24T02:14:13.503326+00:00.

• Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community) · Publisher's source file: Source package: observium-community-latest.tar.gz

  Vendor MIB copy from the Observium Community archive.

  Module: PowerNet-MIB

  Published definition

  upsAdvStateGalaxyVseriesSpecificFault OBJECT-TYPE
     SYNTAX DisplayString
     ACCESS read-only
     STATUS optional
     DESCRIPTION
          "An ASCII string containing 32 flags representing
          current active faults on a Galaxy V series UPS.
          The upsAdvStateAbnormalConditions OID shall be used to report
          active faults as per its description. Additional fault information
          shall be provided through the upsAdvStateGalaxyVseriesSpecificFault OID.
          If the Network Card is unable to determine the values of the flags, this
          variable is set to 'UNKNOWN'. If this variable is not
          supported by the connected UPS, this variable is set to
          'NOT SUPPORTED'.
  
          The flags are numbered from 1 to 32, and read from left to
          right. The flags are defined as follows:
  
          Flag  1: Input voltage is out of tolerance
          Flag  2: Input frequency is out of tolerance
          Flag  3: External sync frequency is out of tolerance
          Flag  4: Output frequency is out of tolerance
  
          Flag  5: The static bypass switch needs a technical check but is still fully operational
          Flag  6: Static bypass switch is inoperable. UPS is prevented from going into static bypass operation
          Flag  7: PBUS cable 1 may be damaged
          Flag  8: PBUS cable 2 may be damaged
  
          Flag  9: The parallel system is not configured correctly or is not working correctly
          Flag 10: The UC in the controller box is not working correctly
          Flag 11: Power module surveillance detected a fault
          Flag 12: The SLC in the controller box is not working correctly
  
          Flag 13: No SBS present
          Flag 14: No power module(s) present
          Flag 15: Controller box disabled
          Flag 16: Display communication lost - disconnected
  
          Flag 17: The energy storage surveillance has detected a battery temperature above shutdown limit
          Flag 18: Modular battery cabinet fuse blown
          Flag 19: Battery module temperature sensor not working correctly
          Flag 20: The energy storage surveillance has detected a battery discharge current above shutdown limit
  
          Flag 21: Ground fault detected
          Flag 22: External energy storage monitoring: Minor alarm
          Flag 23: External energy storage monitoring: Major alarm
          Flag 24: Temperature of input and/or output transformer is too high
  
          Flag 25: Parallel breaker status inconsistency detected
          Flag 26: UC communication lost - disconnected
          Flag 27: PMC communication lost - disconnected
          Flag 28: NMC communication lost - disconnected
  
          Flag 29: BMC communication lost - disconnected
          Flag 30: <Reserved>
          Flag 31: <Reserved>
          Flag 32: <Reserved>"
     ::= { upsAdvState 15 }

  Module imports

  {'RFC-1212': ['OBJECT-TYPE'], 'RFC-1215': ['TRAP-TYPE'], 'RFC1155-SMI': ['enterprises', 'IpAddress', 'Gauge', 'TimeTicks'], 'RFC1213-MIB': ['DisplayString'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}

  Related source files and packages:

  • Observium Community original distribution archivePublisher Last-Modified: Tue, 05 May 2026 13:47:48 GMT; 127.4 MiB
  
  Source location: PowerNet-MIB::upsAdvStateGalaxyVseriesSpecificFault.
  Source version and references

  Downloaded: 2026-10-24T02:14:28.042136+00:00.