This persistent variable contains the current T1
Line Build Out configuration for the radio.
For DSX-1 applications, line lengths from 0 to 655 feet
(as measured from the DS-1 connector to the DSX-1
cross connect) are selectable. The five partition
arrangement meets ANSI T1.102-1993 requirements when
using ABAM cable.
The default value for this variable is 'lb-0-133-ft'.
Parsed from file WESTERN-MULTIPLEX-RAD10006-MIB.mib
Module: WESTERN-MULTIPLEX-RAD10006-MIB
Vendor: Western Multiplex
Module: WESTERN-MULTIPLEX-RAD10006-MIB
[Automatically extracted from oidview.com]
cnfgT1LineBuildOut OBJECT-TYPE SYNTAX INTEGER { lb-0-133-ft(1), lb-133-266-ft(2), lb-266-399-ft(3), lb-399-533-ft(4), lb-533-655-ft(5) } ACCESS read-write STATUS mandatory DESCRIPTION "This persistent variable contains the current T1 Line Build Out configuration for the radio. For DSX-1 applications, line lengths from 0 to 655 feet (as measured from the DS-1 connector to the DSX-1 cross connect) are selectable. The five partition arrangement meets ANSI T1.102-1993 requirements when using ABAM cable. The default value for this variable is 'lb-0-133-ft'." ::= { config 2 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3727.20.20.1.1 | cnfgT1LineCode | 0 | 0 | This persistent variable contains the current T1 line encoding/decoding method. 'B8ZS' selects the Bipolar With 8-bit Zero Substi… |
| 1.3.6.1.4.1.3727.20.20.1.3 | cnfgT1NearEndRadioLoopback | 0 | 0 | This non-persistent variable contains the current state of the loopback mode for the radio side of the T1 channel of the radio. 'e… |
| 1.3.6.1.4.1.3727.20.20.1.4 | cnfgT1FarEndRadioLoopback | 0 | 0 | This non-persistent variable contains the current state of the loopback mode for the radio side of the T1 channel of the remote r… |
| 1.3.6.1.4.1.3727.20.20.1.5 | cnfgT1InputAlarm | 0 | 0 | This non-persistent variable contains the configuration setting of the T1 channel input. It allows the SNMP user to control T1 ch… |
| 1.3.6.1.4.1.3727.20.20.1.6 | cnfgAIS | 0 | 0 | This non-persistent variable contains the configuration setting of the AIS output. It allows the SNMP user to control AIS output.… |
| 1.3.6.1.4.1.3727.20.20.1.7 | cnfgOrderwireAddr | 0 | 0 | This persistent variable contains the current number of the two-digit engineering orderwire (EOW) phone number of the handset con… |
| 1.3.6.1.4.1.3727.20.20.1.8 | cnfgLinkSecurityCode | 0 | 0 | This persistent variable contains the current number of the 12-byte security code. It allows the SNMP user to read and set the li… |
| 1.3.6.1.4.1.3727.20.20.1.9 | cnfgLearningFilter | 0 | 0 | This persistent variable configures the learning filter. 'disabled' turns off the learning filter. 'enabled' turns on the learnin… |
| 1.3.6.1.4.1.3727.20.20.1.10 | cnfgFiberOpticInterface | 0 | 0 | This persistent variable configures the fiber interface. 'disabled' turns off the fiber interface. 'enabled' turns on the fiber i… |
| 1.3.6.1.4.1.3727.20.20.1.11 | cnfgEthernetDuplex | 0 | 0 | This persistent variable contains the current configuration of the ethernet communication mode. 'full-duplex' indicates ethernet … |
| 1.3.6.1.4.1.3727.20.20.1.12 | cnfgDataRate | 0 | 0 | This persistent variable contains the current configuration of the data rate. 'full-duplex-45-MB' indicates 45 MB data rate with … |
| 1.3.6.1.4.1.3727.20.20.1.13 | cnfgInterfaceType | 0 | 0 | This persistent variable contains the current configuration of interface type. 't1-100BaseT' indicates 100BaseT and a T1 channel.… |
| 1.3.6.1.4.1.3727.20.20.1.14 | cnfgIDUSWVersion | 0 | 0 | This persistent variable contains the current number of the 4-byte IDU software Version. There is no default value for this varia… |
| 1.3.6.1.4.1.3727.20.20.1.15 | cnfgNMUSWVersion | 0 | 0 | This persistent variable contains the current number of the 4-byte NMU software Version. There is no default value for this varia… |