This is the error code that will be returned to an ISDN
switch when digital connections are being blocked.
Default
= 58.
Parsed from file UDS1-MIB.mib.txt
Company: None
Module: UDS1-MIB
This is the error code that will be returned to an ISDN
switch when digital connections are being blocked.
Default
= 58.
Parsed from file UDS1-MIB.mib
Module: UDS1-MIB
Vendor: UTStarcom Incorporated
Module: UDS1-MIB
[Automatically extracted from oidview.com]
uds1CfgDgtlBlockErrCode OBJECT-TYPE SYNTAX INTEGER (0..127) ACCESS read-write STATUS mandatory DESCRIPTION "This is the error code that will be returned to an ISDN switch when digital connections are being blocked. Default = 58." ::= { uds1ConfigEntry 16 }
uds1CfgDgtlBlockErrCode OBJECT-TYPE SYNTAX INTEGER (0..127) ACCESS read-write STATUS mandatory DESCRIPTION "This is the error code that will be returned to an ISDN switch when digital connections are being blocked. Default = 58." ::= { uds1ConfigEntry 16 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.429.1.4.1.1.1 | uds1CfgIndex | 0 | 0 | The index value which uniquely identifies the CSU to which this entry is applicable. The value corresponds to ds1CSUIndex in the… |
| 1.3.6.1.4.1.429.1.4.1.1.2 | uds1CfgRespToRemoteLoopbk | 0 | 0 | This object configures the specified CSU to either ignore or respond to remotely initiated loopback requests. |
| 1.3.6.1.4.1.429.1.4.1.1.3 | uds1CfgJitterAttenuation | 0 | 0 | This object is used to select how the jitter attenuation circuit on the CSU is to be used. It can be used to attenuate jitter on… |
| 1.3.6.1.4.1.429.1.4.1.1.4 | uds1CfgXmitLineBuildOut | 0 | 0 | This object is used to configure the amount of attenuation that is to be applied to the transmit signal in order to control cross… |
| 1.3.6.1.4.1.429.1.4.1.1.5 | uds1CfgAutoBusyEnable | 0 | 0 | This object is used to enable or disable the automatic busy out feature for all timeslots on the specified CSU. If enabled, when… |
| 1.3.6.1.4.1.429.1.4.1.1.6 | uds1CfgDialInAdr | 0 | 0 | This object identifies whether or not DNIS digits will be transferred as part of the call setup for the specified T1 line. |
| 1.3.6.1.4.1.429.1.4.1.1.7 | uds1CfgZeroCoding | 0 | 0 | This object defines the type of zero coding used on the specified DS1. It provides some values that are not present in the exper… |
| 1.3.6.1.4.1.429.1.4.1.1.8 | uds1CfgDialInOutTrunkSt | 0 | 0 | This will set the Dial-in/Dial-out trunk start signal type. Default = wink(1). |
| 1.3.6.1.4.1.429.1.4.1.1.9 | uds1CfgDialInAdrAckWinkEn | 0 | 0 | Allows to enable/disable an acknowledgement wink after the dial-in address information has been received. |
| 1.3.6.1.4.1.429.1.4.1.1.10 | uds1CfgDialOutAdrDly | 0 | 0 | Allows an adjustable delay on sending out address information from the T1 NAC to the TELCO. |
| 1.3.6.1.4.1.429.1.4.1.1.11 | uds1CfgStuffByteValue | 0 | 0 | The stuffed byte to send to TELCO for inactive DS0 in Fractional T1. |
| 1.3.6.1.4.1.429.1.4.1.1.12 | uds1CfgDialInOutTrunkType | 0 | 0 | This will set the Dial-In/Dial-out trunk type. Default = eAndMTypeII(1). |
| 1.3.6.1.4.1.429.1.4.1.1.13 | uds1CfgPriSwitchType | 0 | 0 | uds1CfgPriSwitchtype |
| 1.3.6.1.4.1.429.1.4.1.1.14 | uds1CfgIdleByte | 0 | 0 | This sets the idle byte pattern for the T1-PRI ISDN NAC. The setting takes effect at NAC boot time. Default = 0xFE. |
| 1.3.6.1.4.1.429.1.4.1.1.15 | uds1CfgAnlgBlockErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when analog connections are being blocked. Default = 58. |
| 1.3.6.1.4.1.429.1.4.1.1.17 | uds1CfgNoMdmAvailErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when there are no modems available to accept the requested connect… |
| 1.3.6.1.4.1.429.1.4.1.1.18 | uds1CfgNoIgwsAvailErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when no IGWS connections are available. Default = 58. |
| 1.3.6.1.4.1.429.1.4.1.1.19 | uds1CfgChanBlockErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when connections to a specific B channel are being blocked. Default… |
| 1.3.6.1.4.1.429.1.4.1.1.20 | uds1CfgBlockCallType | 0 | 0 | This object determines if a PRI span line will block calls of a specific type. This object does not apply to a NAC operating in … |
| 1.3.6.1.4.1.429.1.4.1.1.21 | uds1CfgNfasId | 0 | 0 | This defines the NFAS ID associated with a PRI span line. This object does not apply to Rob Bit T1 operation. Default = 0. |
| 1.3.6.1.4.1.429.1.4.1.1.22 | uds1CfgNfasDChannel | 0 | 0 | This determines how a PRI span line will use the DS0 normally assigned as a D channel when NFAS is being used. This object does n… |
| 1.3.6.1.4.1.429.1.4.1.1.23 | uds1CfgShrtHaulDist | 0 | 0 | Variuos distance ranges supported by Short Haul NIC Default=len0thru133Ft. |
| 1.3.6.1.4.1.429.1.4.1.1.24 | uds1CfgCallProceedingRsp | 0 | 0 | This object determines to send CALL_PROCEEDING and CONNECT response, when a SETUP message is received from TELCO. Default = ON. |
| 1.3.6.1.4.1.429.1.4.1.1.25 | uds1CfgAlertingRsp | 0 | 0 | This object determines to send ALERTING response, when a SETUP message is received from TELCO. Default = OFF. |
| 1.3.6.1.4.1.429.1.4.1.1.26 | uds1CfgServiceState | 0 | 0 | This objects configures the service state of the DS1 and will configure the state for power up if saved to NVRAM. Default= inServ… |
| 1.3.6.1.4.1.429.1.4.1.1.27 | uds1CfgIcbKeyword | 0 | 0 | This is the keyword used for DASS2 Incoming Call Barring control. |
| 1.3.6.1.4.1.429.1.4.1.1.28 | uds1CfgOverlapRxMode | 0 | 0 | This object allows dialed digits to arrive in separate messages. Default = disabled(2) |
| 1.3.6.1.4.1.429.1.4.1.1.29 | uds1CfgEandMnoAddrTimer | 0 | 0 | This object is for E&M type II trunks with no DNIS address. If timer is >0, the ch T1 NAC will flush calls upon timer expiration,… |
| 1.3.6.1.4.1.429.1.4.1.1.30 | uds1CfgSeizureWinkDly | 0 | 0 | Allows an adjustable delay on sending out address information from the T1 NAC to the TELCO. Default=18. |