This object is used to enable or disable the automatic busy
out feature for all timeslots on the specified CSU. If
enabled, when a modem is considered idle and that modem is
not sending the idle pattern to the T1 Card on the TDM bus,
the timeslot will be busied out.
Parsed from file UDS1-MIB.mib.txt
Company: None
Module: UDS1-MIB
This object is used to enable or disable the automatic busy
out feature for all timeslots on the specified CSU. If
enabled, when a modem is considered idle and that modem is
not sending the idle pattern to the T1 Card on the TDM bus,
the timeslot will be busied out.
Parsed from file UDS1-MIB.mib
Module: UDS1-MIB
Vendor: UTStarcom Incorporated
Module: UDS1-MIB
[Automatically extracted from oidview.com]
uds1CfgAutoBusyEnable OBJECT-TYPE SYNTAX INTEGER{ disabled(1), enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to enable or disable the automatic busy out feature for all timeslots on the specified CSU. If enabled, when a modem is considered idle and that modem is not sending the idle pattern to the T1 Card on the TDM bus, the timeslot will be busied out." ::= { uds1ConfigEntry 5 }
uds1CfgAutoBusyEnable OBJECT-TYPE SYNTAX INTEGER{ disabled(1), enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to enable or disable the automatic busy out feature for all timeslots on the specified CSU. If enabled, when a modem is considered idle and that modem is not sending the idle pattern to the T1 Card on the TDM bus, the timeslot will be busied out." ::= { uds1ConfigEntry 5 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.429.1.4.1.1.1 | uds1CfgIndex | 0 | 0 | The index value which uniquely identifies the CSU to which this entry is applicable. The value corresponds to ds1CSUIndex in the… |
| 1.3.6.1.4.1.429.1.4.1.1.2 | uds1CfgRespToRemoteLoopbk | 0 | 0 | This object configures the specified CSU to either ignore or respond to remotely initiated loopback requests. |
| 1.3.6.1.4.1.429.1.4.1.1.3 | uds1CfgJitterAttenuation | 0 | 0 | This object is used to select how the jitter attenuation circuit on the CSU is to be used. It can be used to attenuate jitter on… |
| 1.3.6.1.4.1.429.1.4.1.1.4 | uds1CfgXmitLineBuildOut | 0 | 0 | This object is used to configure the amount of attenuation that is to be applied to the transmit signal in order to control cross… |
| 1.3.6.1.4.1.429.1.4.1.1.6 | uds1CfgDialInAdr | 0 | 0 | This object identifies whether or not DNIS digits will be transferred as part of the call setup for the specified T1 line. |
| 1.3.6.1.4.1.429.1.4.1.1.7 | uds1CfgZeroCoding | 0 | 0 | This object defines the type of zero coding used on the specified DS1. It provides some values that are not present in the exper… |
| 1.3.6.1.4.1.429.1.4.1.1.8 | uds1CfgDialInOutTrunkSt | 0 | 0 | This will set the Dial-in/Dial-out trunk start signal type. Default = wink(1). |
| 1.3.6.1.4.1.429.1.4.1.1.9 | uds1CfgDialInAdrAckWinkEn | 0 | 0 | Allows to enable/disable an acknowledgement wink after the dial-in address information has been received. |
| 1.3.6.1.4.1.429.1.4.1.1.10 | uds1CfgDialOutAdrDly | 0 | 0 | Allows an adjustable delay on sending out address information from the T1 NAC to the TELCO. |
| 1.3.6.1.4.1.429.1.4.1.1.11 | uds1CfgStuffByteValue | 0 | 0 | The stuffed byte to send to TELCO for inactive DS0 in Fractional T1. |
| 1.3.6.1.4.1.429.1.4.1.1.12 | uds1CfgDialInOutTrunkType | 0 | 0 | This will set the Dial-In/Dial-out trunk type. Default = eAndMTypeII(1). |
| 1.3.6.1.4.1.429.1.4.1.1.13 | uds1CfgPriSwitchType | 0 | 0 | uds1CfgPriSwitchtype |
| 1.3.6.1.4.1.429.1.4.1.1.14 | uds1CfgIdleByte | 0 | 0 | This sets the idle byte pattern for the T1-PRI ISDN NAC. The setting takes effect at NAC boot time. Default = 0xFE. |
| 1.3.6.1.4.1.429.1.4.1.1.15 | uds1CfgAnlgBlockErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when analog connections are being blocked. Default = 58. |
| 1.3.6.1.4.1.429.1.4.1.1.16 | uds1CfgDgtlBlockErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when digital connections are being blocked. Default = 58. |
| 1.3.6.1.4.1.429.1.4.1.1.17 | uds1CfgNoMdmAvailErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when there are no modems available to accept the requested connect… |
| 1.3.6.1.4.1.429.1.4.1.1.18 | uds1CfgNoIgwsAvailErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when no IGWS connections are available. Default = 58. |
| 1.3.6.1.4.1.429.1.4.1.1.19 | uds1CfgChanBlockErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when connections to a specific B channel are being blocked. Default… |
| 1.3.6.1.4.1.429.1.4.1.1.20 | uds1CfgBlockCallType | 0 | 0 | This object determines if a PRI span line will block calls of a specific type. This object does not apply to a NAC operating in … |
| 1.3.6.1.4.1.429.1.4.1.1.21 | uds1CfgNfasId | 0 | 0 | This defines the NFAS ID associated with a PRI span line. This object does not apply to Rob Bit T1 operation. Default = 0. |
| 1.3.6.1.4.1.429.1.4.1.1.22 | uds1CfgNfasDChannel | 0 | 0 | This determines how a PRI span line will use the DS0 normally assigned as a D channel when NFAS is being used. This object does n… |
| 1.3.6.1.4.1.429.1.4.1.1.23 | uds1CfgShrtHaulDist | 0 | 0 | Variuos distance ranges supported by Short Haul NIC Default=len0thru133Ft. |
| 1.3.6.1.4.1.429.1.4.1.1.24 | uds1CfgCallProceedingRsp | 0 | 0 | This object determines to send CALL_PROCEEDING and CONNECT response, when a SETUP message is received from TELCO. Default = ON. |
| 1.3.6.1.4.1.429.1.4.1.1.25 | uds1CfgAlertingRsp | 0 | 0 | This object determines to send ALERTING response, when a SETUP message is received from TELCO. Default = OFF. |
| 1.3.6.1.4.1.429.1.4.1.1.26 | uds1CfgServiceState | 0 | 0 | This objects configures the service state of the DS1 and will configure the state for power up if saved to NVRAM. Default= inServ… |
| 1.3.6.1.4.1.429.1.4.1.1.27 | uds1CfgIcbKeyword | 0 | 0 | This is the keyword used for DASS2 Incoming Call Barring control. |
| 1.3.6.1.4.1.429.1.4.1.1.28 | uds1CfgOverlapRxMode | 0 | 0 | This object allows dialed digits to arrive in separate messages. Default = disabled(2) |
| 1.3.6.1.4.1.429.1.4.1.1.29 | uds1CfgEandMnoAddrTimer | 0 | 0 | This object is for E&M type II trunks with no DNIS address. If timer is >0, the ch T1 NAC will flush calls upon timer expiration,… |
| 1.3.6.1.4.1.429.1.4.1.1.30 | uds1CfgSeizureWinkDly | 0 | 0 | Allows an adjustable delay on sending out address information from the T1 NAC to the TELCO. Default=18. |