Sets the duration, in seconds, of the delay between when
the modem senses loss of carrier and when it attempts to
reestablish a leased line connection. The default setting
of 15 should be appropriate for most installations.
Parsed from file MDM-MIB.mib.txt
Company: None
Module: MDM-MIB
Sets the duration, in seconds, of the delay between when
the modem senses loss of carrier and when it attempts to
reestablish a leased line connection. The default setting
of 15 should be appropriate for most installations.
Parsed from file MDM-MIB.mib
Module: MDM-MIB
Vendor: UTStarcom Incorporated
Module: MDM-MIB
[Automatically extracted from oidview.com]
mdmLiLeasedLineRestDelay OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Sets the duration, in seconds, of the delay between when the modem senses loss of carrier and when it attempts to reestablish a leased line connection. The default setting of 15 should be appropriate for most installations." ::= { mdmLiEntry 11 }
mdmLiLeasedLineRestDelay OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Sets the duration, in seconds, of the delay between when the modem senses loss of carrier and when it attempts to reestablish a leased line connection. The default setting of 15 should be appropriate for most installations." ::= { mdmLiEntry 11 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.429.1.6.2.1.1.1 | mdmLiIndex | 0 | 0 | Index into the Line Interface table. This index is the value from the chassis mib entity relation table that is applicable for a… |
| 1.3.6.1.4.1.429.1.6.2.1.1.2 | mdmLiDialPause | 0 | 0 | Duration in seconds for the pause(') option in the dial command and the pause between command re-executions(> and A>) Default = 2… |
| 1.3.6.1.4.1.429.1.6.2.1.1.3 | mdmLiCarrierRecDelay | 0 | 0 | Duration in 10ths of a second that the remote modem's carrier signal must be present before recognition. Ignored at speeds above… |
| 1.3.6.1.4.1.429.1.6.2.1.1.4 | mdmLiCarrierLoss | 0 | 0 | Duration in 10ths of a second the modem waits after loss of carrier before hanging up. This allows the modem to distinguish betw… |
| 1.3.6.1.4.1.429.1.6.2.1.1.5 | mdmLiToneDialTiming | 0 | 0 | Duration and spacing in milliseconds of dialed Touch Tones. Equates to the modem's S10 register. Default=70. |
| 1.3.6.1.4.1.429.1.6.2.1.1.6 | mdmLiDteRxDataDelay | 0 | 0 | Duration in 10ths of a second that the modem inserts a RX transmission delay between CD and the first recieved character. Intend… |
| 1.3.6.1.4.1.429.1.6.2.1.1.7 | mdmLiTransmiter | 0 | 0 | Enables the modem to transmit data. Corresponds to the modem 'C' register. Default=2. |
| 1.3.6.1.4.1.429.1.6.2.1.1.8 | mdmLiDialMode | 0 | 0 | Determines whether the modem uses pulse or tone for dialing when initiating outgoing calls. Equates to the P and T registers in… |
| 1.3.6.1.4.1.429.1.6.2.1.1.9 | mdmLiGuardTone | 0 | 0 | This object is required for modems answering calls that originate from sites outside of North America. The modem's must be opera… |
| 1.3.6.1.4.1.429.1.6.2.1.1.10 | mdmLiLeasedLine | 0 | 0 | Enables modem to operate in leased line mode. When enabled the local an remote modems make a continuous connection without diali… |
| 1.3.6.1.4.1.429.1.6.2.1.1.12 | mdmLiPulseMakeBreak | 0 | 0 | Determines the ratio of off hook to on hook interval for Pulse dialing. Equates to the modem's &P register. Default=North Americ… |
| 1.3.6.1.4.1.429.1.6.2.1.1.13 | mdmLiAnswerTone | 0 | 0 | Disables the 2100 Hz Answer tone allowing V.42 modems to connect more quickly and/or eliminating problems with older 2400-bps mod… |
| 1.3.6.1.4.1.429.1.6.2.1.1.14 | mdmLiRemoteEscGuardTime | 0 | 0 | Sets the duration in 20 millisecond increments of the guard time that the modem requires preceding and following the remote escap… |
| 1.3.6.1.4.1.429.1.6.2.1.1.15 | mdmLiRemoteEscChar | 0 | 0 | Specifies the decimal value of the character used in the remote access escape code for entering online command mode on this modem… |
| 1.3.6.1.4.1.429.1.6.2.1.1.16 | mdmLiRemAccessLimit | 0 | 0 | Determines the number of attempts to enter remote online command mode that are allowed for any one connection. The default is 0 … |
| 1.3.6.1.4.1.429.1.6.2.1.1.17 | mdmLiRemPassword0 | 0 | 0 | The password that allows a dial-in user to gain view only access to this modems parameters. A maximum of 8 characters is allowed. |
| 1.3.6.1.4.1.429.1.6.2.1.1.18 | mdmLiRemPassword1 | 0 | 0 | The password used by a dial-in user to gain read-write access to this modems configuration. Maximum length is 8 characters. |
| 1.3.6.1.4.1.429.1.6.2.1.1.19 | mdmLiTransmitLevel | 0 | 0 | Specifies the signal level of the modem transmitter in negative db. |
| 1.3.6.1.4.1.429.1.6.2.1.1.20 | mdmLiSrc | 0 | 0 | Specifies either NIC or TDM as the source for the line interface. |