Sets the duration in 20 millisecond increments of the guard
time that the modem requires preceding and following the
remote escape sequence.
The default is 200 or 4 seconds.
Parsed from file MDM-MIB.mib.txt
Company: None
Module: MDM-MIB
Sets the duration in 20 millisecond increments of the guard
time that the modem requires preceding and following the
remote escape sequence.
The default is 200 or 4 seconds.
Parsed from file MDM-MIB.mib
Module: MDM-MIB
Vendor: UTStarcom Incorporated
Module: MDM-MIB
[Automatically extracted from oidview.com]
mdmLiRemoteEscGuardTime OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Sets the duration in 20 millisecond increments of the guard time that the modem requires preceding and following the remote escape sequence. The default is 200 or 4 seconds." ::= { mdmLiEntry 14 }
mdmLiRemoteEscGuardTime OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Sets the duration in 20 millisecond increments of the guard time that the modem requires preceding and following the remote escape sequence. The default is 200 or 4 seconds." ::= { mdmLiEntry 14 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.429.1.6.2.1.1.1 | mdmLiIndex | 0 | 0 | Index into the Line Interface table. This index is the value from the chassis mib entity relation table that is applicable for a… |
| 1.3.6.1.4.1.429.1.6.2.1.1.2 | mdmLiDialPause | 0 | 0 | Duration in seconds for the pause(') option in the dial command and the pause between command re-executions(> and A>) Default = 2… |
| 1.3.6.1.4.1.429.1.6.2.1.1.3 | mdmLiCarrierRecDelay | 0 | 0 | Duration in 10ths of a second that the remote modem's carrier signal must be present before recognition. Ignored at speeds above… |
| 1.3.6.1.4.1.429.1.6.2.1.1.4 | mdmLiCarrierLoss | 0 | 0 | Duration in 10ths of a second the modem waits after loss of carrier before hanging up. This allows the modem to distinguish betw… |
| 1.3.6.1.4.1.429.1.6.2.1.1.5 | mdmLiToneDialTiming | 0 | 0 | Duration and spacing in milliseconds of dialed Touch Tones. Equates to the modem's S10 register. Default=70. |
| 1.3.6.1.4.1.429.1.6.2.1.1.6 | mdmLiDteRxDataDelay | 0 | 0 | Duration in 10ths of a second that the modem inserts a RX transmission delay between CD and the first recieved character. Intend… |
| 1.3.6.1.4.1.429.1.6.2.1.1.7 | mdmLiTransmiter | 0 | 0 | Enables the modem to transmit data. Corresponds to the modem 'C' register. Default=2. |
| 1.3.6.1.4.1.429.1.6.2.1.1.8 | mdmLiDialMode | 0 | 0 | Determines whether the modem uses pulse or tone for dialing when initiating outgoing calls. Equates to the P and T registers in… |
| 1.3.6.1.4.1.429.1.6.2.1.1.9 | mdmLiGuardTone | 0 | 0 | This object is required for modems answering calls that originate from sites outside of North America. The modem's must be opera… |
| 1.3.6.1.4.1.429.1.6.2.1.1.10 | mdmLiLeasedLine | 0 | 0 | Enables modem to operate in leased line mode. When enabled the local an remote modems make a continuous connection without diali… |
| 1.3.6.1.4.1.429.1.6.2.1.1.11 | mdmLiLeasedLineRestDelay | 0 | 0 | Sets the duration, in seconds, of the delay between when the modem senses loss of carrier and when it attempts to reestablish a l… |
| 1.3.6.1.4.1.429.1.6.2.1.1.12 | mdmLiPulseMakeBreak | 0 | 0 | Determines the ratio of off hook to on hook interval for Pulse dialing. Equates to the modem's &P register. Default=North Americ… |
| 1.3.6.1.4.1.429.1.6.2.1.1.13 | mdmLiAnswerTone | 0 | 0 | Disables the 2100 Hz Answer tone allowing V.42 modems to connect more quickly and/or eliminating problems with older 2400-bps mod… |
| 1.3.6.1.4.1.429.1.6.2.1.1.15 | mdmLiRemoteEscChar | 0 | 0 | Specifies the decimal value of the character used in the remote access escape code for entering online command mode on this modem… |
| 1.3.6.1.4.1.429.1.6.2.1.1.16 | mdmLiRemAccessLimit | 0 | 0 | Determines the number of attempts to enter remote online command mode that are allowed for any one connection. The default is 0 … |
| 1.3.6.1.4.1.429.1.6.2.1.1.17 | mdmLiRemPassword0 | 0 | 0 | The password that allows a dial-in user to gain view only access to this modems parameters. A maximum of 8 characters is allowed. |
| 1.3.6.1.4.1.429.1.6.2.1.1.18 | mdmLiRemPassword1 | 0 | 0 | The password used by a dial-in user to gain read-write access to this modems configuration. Maximum length is 8 characters. |
| 1.3.6.1.4.1.429.1.6.2.1.1.19 | mdmLiTransmitLevel | 0 | 0 | Specifies the signal level of the modem transmitter in negative db. |
| 1.3.6.1.4.1.429.1.6.2.1.1.20 | mdmLiSrc | 0 | 0 | Specifies either NIC or TDM as the source for the line interface. |