The value of vRtrMplsLspPreference specifies the preference for
the LSP. This value is used for load balancing between multiple
LSPs that exist between the same ingress and egress routers.
By default, traffic is load balanced among the LSPs, since all
LSPs have the same preference. To prefer one LSP over another,
change the preference value for that LSP. The LSP with the
lowest preference is used.
When the value of vRtrMplsLspPathPreference is set to zero (0),
the value of vRtrMplsLspPreference is applied to that specific
LSP/path.
Parsed from file TIMETRA-MPLS-MIB.mib
Module: TIMETRA-MPLS-MIB
vRtrMplsLspPreference OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of vRtrMplsLspPreference specifies the preference for the LSP. This value is used for load balancing between multiple LSPs that exist between the same ingress and egress routers. By default, traffic is load balanced among the LSPs, since all LSPs have the same preference. To prefer one LSP over another, change the preference value for that LSP. The LSP with the lowest preference is used. When the value of vRtrMplsLspPathPreference is set to zero (0), the value of vRtrMplsLspPreference is applied to that specific LSP/path." DEFVAL { 7 } ::= { vRtrMplsLspEntry 23 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.1 | vRtrMplsLspIndex | 0 | 0 | The unique value which identifies this Labeled Switch Path (LSP) for this virtual router in the Alcatel 7x50 SR system. It is a … |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.2 | vRtrMplsLspRowStatus | 0 | 0 | The row status used for creation, deletion, or control of vRtrMplsLspTable entries. Before the row can be placed into the 'activ… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.3 | vRtrMplsLspLastChange | 0 | 0 | The sysUpTime when this row was last modified. |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.4 | vRtrMplsLspName | 0 | 0 | Administrative name for this Labeled Switch Path. The vRtrMplsLspName must be unique within a virtual router instance. |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.5 | vRtrMplsLspAdminState | 0 | 0 | The desired administrative state for this LSP. |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.6 | vRtrMplsLspOperState | 0 | 0 | The current operational state of this LSP. |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.7 | vRtrMplsLspFromAddr | 0 | 0 | Source IP address of this LSP. If vRtrMplsLspFromAddr has not been explicitly set, the system IP address will be used. |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.8 | vRtrMplsLspToAddr | 0 | 0 | Destination IP address of this LSP. This LSP will not be signaled until vRtrMplsLspToAddr is explicitly set. |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.9 | vRtrMplsLspType | 0 | 0 | The vRtrMplsLspType object is an enumerated value that indicates whether the label value is statically or dynamically assigned o… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.10 | vRtrMplsLspOutSegIndx | 0 | 0 | The vRtrMplsLspOutSegIndx is the index value of the entry in the mplsOutSegmentTable associated with this vRtrMplsLspEntry when v… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.11 | vRtrMplsLspRetryTimer | 0 | 0 | The value of vRtrMplsLspRetryTimer specifies the time in seconds the software will wait before attempting the establish the faile… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.12 | vRtrMplsLspRetryLimit | 0 | 0 | The value of vRtrMplsLspRetryLimit specifies the number of attempts the software should make to reestablish a failed LSP before t… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.13 | vRtrMplsLspMetric | 0 | 0 | The value of vRtrMplsLspMetric specifies the metric for this LSP which is used to select an LSP among a set of LSPs which are des… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.14 | vRtrMplsLspDecrementTtl | 0 | 0 | When the value of vRtrMplsLspDecrementTtl is 'true', the ingress ESR writes the TTL of the IP packet into the label and each tran… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.15 | vRtrMplsLspCspf | 0 | 0 | When the value of vRtrMplsLspCspf is 'true', CSPF computation for constrained-path LSP is enabled. When the value of vRtrMplsLsp… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.16 | vRtrMplsLspFastReroute | 0 | 0 | When the value of vRtrMplsLspFastReroute is 'true', fast reroute is enabled. A pre-computed detour LSP is created from each nod… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.17 | vRtrMplsLspFRHopLimit | 0 | 0 | The value of vRtrMplsLspFRHopLimit specifies the total number of hops a detour LSP can take before merging back onto the main LSP… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.18 | vRtrMplsLspFRBandwidth | 0 | 0 | The value of vRtrMplsLspFRBandwidth specified the amount of bandwidth in mega-bits per second (Mbps) to be reserved for the detou… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.19 | vRtrMplsLspClassOfService | 0 | 0 | The name of the class of service value to be assigned to all packets on the LSP is specified with vRtrMplsLspClassOfService. The … |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.20 | vRtrMplsLspSetupPriority | 0 | 0 | The value of vRtrMplsLspSetupPriority specifies the setup priority to use when insufficient bandwidth is available to setup a LS… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.21 | vRtrMplsLspHoldPriority | 0 | 0 | The value of vRtrMplsLspHoldPriority specifies the hold priority to use when insufficient bandwidth is available to setup a LSP.… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.22 | vRtrMplsLspRecord | 0 | 0 | When the value of vRtrMplsLspRecord is 'true', recording of all the hops that a LSP traverses is enabled. When the value of vRtr… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.24 | vRtrMplsLspBandwidth | 0 | 0 | The value of vRtrMplsLspBandwidth specifies the amount of bandwidth in mega-bits per second (Mbps) to be reserved for the LSP. A … |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.25 | vRtrMplsLspBwProtect | 0 | 0 | When vRtrMplsLspBwProtect has a value of 'true', bandwidth protection is enabled on a LSP. LSPs that reserve bandwidth will be u… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.26 | vRtrMplsLspHopLimit | 0 | 0 | The value of vRtrMplsLspHopLimit specifies the maximum number of hops that a LSP will traverse including the ingress and egress E… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.27 | vRtrMplsLspNegotiatedMTU | 0 | 0 | The value of vRtrMplsLspNegotiatedMTU specifies the size for the Maximum transmission unit (MTU) that is negotiated during LSP es… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.28 | vRtrMplsLspRsvpResvStyle | 0 | 0 | The value of vRtrMplsLspRsvpResvStyle specifies the reservation style for RSVP. The reservation style can be set to 'Shared- Expl… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.29 | vRtrMplsLspRsvpAdspec | 0 | 0 | When the value of vRtrMplsLspRsvpAdspec is 'true', the ADSPEC object will be included in RSVP messages. When the value of vRtrMpl… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.30 | vRtrMplsLspFRMethod | 0 | 0 | The value of vRtrMplsLspFRMethod specifies the fast reroute method used. In the 'One-to-one Backup' method, a backup LSP is esta… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.31 | vRtrMplsLspFRNodeProtect | 0 | 0 | Setting the value of vRtrMplsLspFRNodeProtect to 'true' enables node protection i.e. protection against the failure of a node on… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.32 | vRtrMplsLspAdminGroupInclude | 0 | 0 | The value of vRtrMplsLspAdminGroupInclude is a bit-map that specifies a list of admin groups that should be included when this LS… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.33 | vRtrMplsLspAdminGroupExclude | 0 | 0 | The value of vRtrMplsLspAdminGroupExclude is a bit-map that specifies a list of admin groups that should be excluded when this LS… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.34 | vRtrMplsLspAdaptive | 0 | 0 | Setting the value of vRtrMplsLspAdaptive to 'true' enables make-before-break functionality for the LSP. When the attributes of an… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.35 | vRtrMplsLspInheritance | 0 | 0 | For each writable object in this row that can be configured to inherit its value from the corresponding object in the vRtrMplsGen… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.36 | vRtrMplsLspOptimizeTimer | 0 | 0 | The value of vRtrMplsLspOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.37 | vRtrMplsLspOperFastReroute | 0 | 0 | The value of vRtrMplsLspOperFastReroute specifies whether the operational LSP has fast reroute enabled or disabled. When make-bef… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.38 | vRtrMplsLspFRObject | 0 | 0 | The value of vRtrMplsLspFRObject specifies whether fast reroute, for LSPs using 'Facility Backup', is signalled with or without t… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.39 | vRtrMplsLspHoldTimer | 0 | 0 | The value of vRtrMplsLspHoldTimer specifies the time, in seconds, for which the ingress node holds a bit before programming its d… |
| 1.3.6.1.4.1.6527.3.1.2.6.1.1.40 | vRtrMplsLspCspfTeMetricEnabled | 0 | 0 | The value of vRtrMplsLspCspfTeMetricEnabled specifies whether the TE metric would be used for the purpose of the LSP path comput… |