Framing type. The choices for this field are:
ESF - Extended Super Frame (24 frames/ESF).
Valid for T1.
D4 - Conventional Super Frame (12 frames/SF).
Valid for T1.
with CRC-4 - Cyclic Redundancy Check, 4 bits.
Valid for E1.
without CRC-4 - CRC not checked.
Valid for E1.
M13 - A DS-3 framing fromat. See C-Bit parity.
Valid for T3.
C-Bit Parity - The synchronous DS-3 C-Bit Parity is a structure
that can be used to multiplex 28 DS-1 signals to
the DS-3 signal level. In C-Bit Parity, the
X-Bit channel is used to transmit failure
conditions from the far end to the near end of a
system.
Valid for T3.
G.832/G.804 - Valid with PLCP cell synchronization only.
Valid for ATM E3.
G.751 - Valid with HEC cell synchronization only.
Valid for ATM E3.
T1DM (DDS) - A.T&T. DDS Framing using D4 and time slot 24.
Not Implemented at this time.
SLIC-96 - Special version of D4 framing. Useds 4-D4
frames but changes some of the framing bits.
Not Implemented at this time.
This field applies only to the T1, E1, T3/DS-3 WanProbes and
DS-3 and E3 ATMProbes.
Parsed from file lanprobe.txt
Company: None
Module: PROBE-MIB
Framing type. The choices for this field are:
ESF - Extended Super Frame (24 frames/ESF).
Valid for T1.
D4 - Conventional Super Frame (12 frames/SF).
Valid for T1.
with CRC-4 - Cyclic Redundancy Check, 4 bits.
Valid for E1.
without CRC-4 - CRC not checked.
Valid for E1.
M13 - A DS-3 framing fromat. See C-Bit parity.
Valid for T3.
C-Bit Parity - The synchronous DS-3 C-Bit Parity is a structure
that can be used to multiplex 28 DS-1 signals to
the DS-3 signal level. In C-Bit Parity, the
X-Bit channel is used to transmit failure
conditions from the far end to the near end of a
system.
Valid for T3.
G.832/G.804 - Valid with PLCP cell synchronization only.
Valid for ATM E3.
G.751 - Valid with HEC cell synchronization only.
Valid for ATM E3.
T1DM (DDS) - A.T&T. DDS Framing using D4 and time slot 24.
Not Implemented at this time.
SLIC-96 - Special version of D4 framing. Useds 4-D4
frames but changes some of the framing bits.
Not Implemented at this time.
This field applies only to the T1, E1, T3/DS-3 WanProbes and
DS-3 and E3 ATMProbes.
Parsed from file PROBE-MIB.mib
Module: PROBE-MIB
Vendor: Hewlett-Packard
Module: PROBE-MIB
[Automatically extracted from oidview.com]
netConfigFramingType OBJECT-TYPE SYNTAX INTEGER { esf(1), d4(2), withCRC4(3), withoutCRC4(4), m13(5), cbitParity(6), g804(7), g751(8), t1dm(9), slic96(10) } ACCESS read-write STATUS mandatory DESCRIPTION "Framing type. The choices for this field are: ESF - Extended Super Frame (24 frames/ESF). Valid for T1. D4 - Conventional Super Frame (12 frames/SF). Valid for T1. with CRC-4 - Cyclic Redundancy Check, 4 bits. Valid for E1. without CRC-4 - CRC not checked. Valid for E1. M13 - A DS-3 framing fromat. See C-Bit parity. Valid for T3. C-Bit Parity - The synchronous DS-3 C-Bit Parity is a structure that can be used to multiplex 28 DS-1 signals to the DS-3 signal level. In C-Bit Parity, the X-Bit channel is used to transmit failure conditions from the far end to the near end of a system. Valid for T3. G.832/G.804 - Valid with PLCP cell synchronization only. Valid for ATM E3. G.751 - Valid with HEC cell synchronization only. Valid for ATM E3. T1DM (DDS) - A.T&T. DDS Framing using D4 and time slot 24. Not Implemented at this time. SLIC-96 - Special version of D4 framing. Useds 4-D4 frames but changes some of the framing bits. Not Implemented at this time. This field applies only to the T1, E1, T3/DS-3 WanProbes and DS-3 and E3 ATMProbes." ::= { netConfigEntry 12 }
netConfigFramingType OBJECT-TYPE SYNTAX INTEGER { esf(1), d4(2), withCRC4(3), withoutCRC4(4), m13(5), cbitParity(6), g804(7), g751(8), t1dm(9), slic96(10) } ACCESS read-write STATUS mandatory DESCRIPTION "Framing type. The choices for this field are: ESF - Extended Super Frame (24 frames/ESF). Valid for T1. D4 - Conventional Super Frame (12 frames/SF). Valid for T1. with CRC-4 - Cyclic Redundancy Check, 4 bits. Valid for E1. without CRC-4 - CRC not checked. Valid for E1. M13 - A DS-3 framing fromat. See C-Bit parity. Valid for T3. C-Bit Parity - The synchronous DS-3 C-Bit Parity is a structure that can be used to multiplex 28 DS-1 signals to the DS-3 signal level. In C-Bit Parity, the X-Bit channel is used to transmit failure conditions from the far end to the near end of a system. Valid for T3. G.832/G.804 - Valid with PLCP cell synchronization only. Valid for ATM E3. G.751 - Valid with HEC cell synchronization only. Valid for ATM E3. T1DM (DDS) - A.T&T. DDS Framing using D4 and time slot 24. Not Implemented at this time. SLIC-96 - Special version of D4 framing. Useds 4-D4 frames but changes some of the framing bits. Not Implemented at this time. This field applies only to the T1, E1, T3/DS-3 WanProbes and DS-3 and E3 ATMProbes." ::= { netConfigEntry 12 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.11.2.4.6.1.1.1 | netConfigIfIndex | 0 | 0 | The value of this object uniquely identifies the physical interface on this device for which this entry contains configuration pa… |
1.3.6.1.4.1.11.2.4.6.1.1.2 | netConfigIfSpeed | 0 | 0 | The value of this object indicates the speed of the media. This is equivalent to the MIB-2 object ifSpeed. |
1.3.6.1.4.1.11.2.4.6.1.1.3 | netConfigIPAddress | 0 | 0 | The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConf… |
1.3.6.1.4.1.11.2.4.6.1.1.4 | netConfigSubnetMask | 0 | 0 | The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netCon… |
1.3.6.1.4.1.11.2.4.6.1.1.5 | netConfigRingNumber | 0 | 0 | The value of this object uniquely identifies the physical ring number on which the probe resides. This variable is only meaningfu… |
1.3.6.1.4.1.11.2.4.6.1.1.6 | netConfigPortType | 0 | 0 | This object indicates whether or not the port for this row (indicated in netConfigIfIndex) is monitor only or can transmit as wel… |
1.3.6.1.4.1.11.2.4.6.1.1.7 | netConfigDefaultGateway | 0 | 0 | The IP Address of the default gateway for this Net interface. |
1.3.6.1.4.1.11.2.4.6.1.1.8 | netConfigPhysicalConnector | 0 | 0 | The value of this object indicates the type of physical connector which is currently being used to connect the interface to the n… |
1.3.6.1.4.1.11.2.4.6.1.1.9 | netConfigLinkSpeed | 0 | 0 | Indicates the speed of the media (in one direction). For Fast Ethernet auto-negotiation and Token-Ring speed auto-detection, this… |
1.3.6.1.4.1.11.2.4.6.1.1.10 | netConfigDuplex | 0 | 0 | Indicates whether the interface supports half or full duplex mode. When LinkSpeed is set to auto-negotiate, this field has no ef… |
1.3.6.1.4.1.11.2.4.6.1.1.11 | netConfigLineCode | 0 | 0 | Line coding. The choices for this field are: B8ZS - Binary 8 Zeros Suppress. Used with more recent ESF T1 framing. Comm… |
1.3.6.1.4.1.11.2.4.6.1.1.13 | netConfigChannelRate | 0 | 0 | Channel Rate. The choices for this field are: 56K - Valid for T1. 64K - Valid for T1/E1. 1536bps - Valid for … |
1.3.6.1.4.1.11.2.4.6.1.1.14 | netConfigDataChannel | 0 | 0 | This integer represents the ORed bit fields which can be set to indicate that the probe should monitor the specified channel on t… |
1.3.6.1.4.1.11.2.4.6.1.1.15 | netConfigDataSense | 0 | 0 | Indicates whether the bits on the channel(s) being tested are inverted. A Mark is a signal pulse on the line. A Space is a bit … |
1.3.6.1.4.1.11.2.4.6.1.1.16 | netConfigLinkLayerType | 0 | 0 | Indicates the type of link layer analysis to be performed on the incoming data. This field applies only to WanProbes and ATMProbes |
1.3.6.1.4.1.11.2.4.6.1.1.17 | netConfigNetworkInterface | 0 | 0 | ATM network interface addressing mode. Valid values for this field are: NNI - Network to Network Interface. The Network to Networ… |
1.3.6.1.4.1.11.2.4.6.1.1.18 | netConfigCellSynchronization | 0 | 0 | ATM network interface addressing mode. Valid values for this field are: HEC - The Header Error Control (DEC) is an 8-bit field … |
1.3.6.1.4.1.11.2.4.6.1.1.19 | netConfigReceiverMode | 0 | 0 | Line: When monitoring, the selected challes are presented as the line and equipment signals for decoding and statistics. All cha… |
1.3.6.1.4.1.11.2.4.6.1.1.20 | netConfigMaximumFrameSize | 0 | 0 | The size of the buffer to be allocated at the physical layer for the reception of a frame from the network. Any frames which ar… |