ATM network interface addressing mode. Valid values for this
field are:
HEC - The Header Error Control (DEC) is an 8-bit field and the
fifth byte in the header of an ATM cell. The HEC value
is calculated from the first four bytes of the cell header.
If an error occurs in an ATM cell header, it will be
detected in the HEC field. Cells with HEC errors that can not
be corrected are discarded by the receiving node. The HEC
field can also be used to determine the boundaries of a packet
for cell delineation.
Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.832/G.804
framing.
PLCP - Physical Layer Convergence Protocol. Each cell is preceded
by a 2-byte framing pattern (A1, A2) to enable the receiver to
synchronize to the cells.
Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.751 framing.
This field applies only to ATMProbes
Parsed from file lanprobe.txt
Company: None
Module: PROBE-MIB
ATM network interface addressing mode. Valid values for this
field are:
HEC - The Header Error Control (DEC) is an 8-bit field and the
fifth byte in the header of an ATM cell. The HEC value
is calculated from the first four bytes of the cell header.
If an error occurs in an ATM cell header, it will be
detected in the HEC field. Cells with HEC errors that can not
be corrected are discarded by the receiving node. The HEC
field can also be used to determine the boundaries of a packet
for cell delineation.
Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.832/G.804
framing.
PLCP - Physical Layer Convergence Protocol. Each cell is preceded
by a 2-byte framing pattern (A1, A2) to enable the receiver to
synchronize to the cells.
Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.751 framing.
This field applies only to ATMProbes
Parsed from file PROBE-MIB.mib
Module: PROBE-MIB
Vendor: Hewlett-Packard
Module: PROBE-MIB
[Automatically extracted from oidview.com]
netConfigCellSynchronization OBJECT-TYPE SYNTAX INTEGER { hec(1), plcp(2) } ACCESS read-write STATUS mandatory DESCRIPTION "ATM network interface addressing mode. Valid values for this field are: HEC - The Header Error Control (DEC) is an 8-bit field and the fifth byte in the header of an ATM cell. The HEC value is calculated from the first four bytes of the cell header. If an error occurs in an ATM cell header, it will be detected in the HEC field. Cells with HEC errors that can not be corrected are discarded by the receiving node. The HEC field can also be used to determine the boundaries of a packet for cell delineation. Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.832/G.804 framing. PLCP - Physical Layer Convergence Protocol. Each cell is preceded by a 2-byte framing pattern (A1, A2) to enable the receiver to synchronize to the cells. Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.751 framing. This field applies only to ATMProbes" DEFVAL { 1 } ::= { netConfigEntry 18 }
netConfigCellSynchronization OBJECT-TYPE SYNTAX INTEGER { hec(1), plcp(2) } ACCESS read-write STATUS mandatory DESCRIPTION "ATM network interface addressing mode. Valid values for this field are: HEC - The Header Error Control (DEC) is an 8-bit field and the fifth byte in the header of an ATM cell. The HEC value is calculated from the first four bytes of the cell header. If an error occurs in an ATM cell header, it will be detected in the HEC field. Cells with HEC errors that can not be corrected are discarded by the receiving node. The HEC field can also be used to determine the boundaries of a packet for cell delineation. Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.832/G.804 framing. PLCP - Physical Layer Convergence Protocol. Each cell is preceded by a 2-byte framing pattern (A1, A2) to enable the receiver to synchronize to the cells. Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.751 framing. This field applies only to ATMProbes" DEFVAL { 1 } ::= { netConfigEntry 18 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.4.6.1.1.1 | netConfigIfIndex | 0 | 0 | The value of this object uniquely identifies the physical interface on this device for which this entry contains configuration pa… |
| 1.3.6.1.4.1.11.2.4.6.1.1.2 | netConfigIfSpeed | 0 | 0 | The value of this object indicates the speed of the media. This is equivalent to the MIB-2 object ifSpeed. |
| 1.3.6.1.4.1.11.2.4.6.1.1.3 | netConfigIPAddress | 0 | 0 | The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConf… |
| 1.3.6.1.4.1.11.2.4.6.1.1.4 | netConfigSubnetMask | 0 | 0 | The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netCon… |
| 1.3.6.1.4.1.11.2.4.6.1.1.5 | netConfigRingNumber | 0 | 0 | The value of this object uniquely identifies the physical ring number on which the probe resides. This variable is only meaningfu… |
| 1.3.6.1.4.1.11.2.4.6.1.1.6 | netConfigPortType | 0 | 0 | This object indicates whether or not the port for this row (indicated in netConfigIfIndex) is monitor only or can transmit as wel… |
| 1.3.6.1.4.1.11.2.4.6.1.1.7 | netConfigDefaultGateway | 0 | 0 | The IP Address of the default gateway for this Net interface. |
| 1.3.6.1.4.1.11.2.4.6.1.1.8 | netConfigPhysicalConnector | 0 | 0 | The value of this object indicates the type of physical connector which is currently being used to connect the interface to the n… |
| 1.3.6.1.4.1.11.2.4.6.1.1.9 | netConfigLinkSpeed | 0 | 0 | Indicates the speed of the media (in one direction). For Fast Ethernet auto-negotiation and Token-Ring speed auto-detection, this… |
| 1.3.6.1.4.1.11.2.4.6.1.1.10 | netConfigDuplex | 0 | 0 | Indicates whether the interface supports half or full duplex mode. When LinkSpeed is set to auto-negotiate, this field has no ef… |
| 1.3.6.1.4.1.11.2.4.6.1.1.11 | netConfigLineCode | 0 | 0 | Line coding. The choices for this field are: B8ZS - Binary 8 Zeros Suppress. Used with more recent ESF T1 framing. Comm… |
| 1.3.6.1.4.1.11.2.4.6.1.1.12 | netConfigFramingType | 0 | 0 | Framing type. The choices for this field are: ESF - Extended Super Frame (24 frames/ESF). Valid for T1. D4 -… |
| 1.3.6.1.4.1.11.2.4.6.1.1.13 | netConfigChannelRate | 0 | 0 | Channel Rate. The choices for this field are: 56K - Valid for T1. 64K - Valid for T1/E1. 1536bps - Valid for … |
| 1.3.6.1.4.1.11.2.4.6.1.1.14 | netConfigDataChannel | 0 | 0 | This integer represents the ORed bit fields which can be set to indicate that the probe should monitor the specified channel on t… |
| 1.3.6.1.4.1.11.2.4.6.1.1.15 | netConfigDataSense | 0 | 0 | Indicates whether the bits on the channel(s) being tested are inverted. A Mark is a signal pulse on the line. A Space is a bit … |
| 1.3.6.1.4.1.11.2.4.6.1.1.16 | netConfigLinkLayerType | 0 | 0 | Indicates the type of link layer analysis to be performed on the incoming data. This field applies only to WanProbes and ATMProbes |
| 1.3.6.1.4.1.11.2.4.6.1.1.17 | netConfigNetworkInterface | 0 | 0 | ATM network interface addressing mode. Valid values for this field are: NNI - Network to Network Interface. The Network to Networ… |
| 1.3.6.1.4.1.11.2.4.6.1.1.19 | netConfigReceiverMode | 0 | 0 | Line: When monitoring, the selected challes are presented as the line and equipment signals for decoding and statistics. All cha… |
| 1.3.6.1.4.1.11.2.4.6.1.1.20 | netConfigMaximumFrameSize | 0 | 0 | The size of the buffer to be allocated at the physical layer for the reception of a frame from the network. Any frames which ar… |